EN 15146-2006 en Solid softwood panelling and cladding - Machined profiles without tongue and groove《实心软木厚镶板层板 不带舌和槽的机加工形状》.pdf

《EN 15146-2006 en Solid softwood panelling and cladding - Machined profiles without tongue and groove《实心软木厚镶板层板 不带舌和槽的机加工形状》.pdf》由会员分享，可在线阅读，更多相关《EN 15146-2006 en Solid softwood panelling and cladding - Machined profiles without tongue and groove《实心软木厚镶板层板 不带舌和槽的机加工形状》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15146:2006Solid softwood panelling and cladding Machined profiles without tongue and grooveThe European Standard EN 15146:2006 has the status of a British StandardICS 79.080g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g3

2、8g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 15146:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978-0-580-49967-8National forewordThis British Standar

3、d was published by BSI. It is the UK implementation of EN 15146:2006.The UK participation in its preparation was entrusted to Technical Committee B/543, Round and sawn timber.A list of organizations represented on B/543 can be obtained on request to its secretary.This publication does not purport to

4、 include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15146Dec

5、ember 2006ICS 79.080English VersionSolid softwood panelling and cladding - Machined profileswithout tongue and grooveLambris et bardages en bois massif rsineux - Profilsusins sans rainure et languetteInnen- und Auenbekleidungen aus massivem Nadelholz -Profilholz ohne Nut und FederThis European Stand

6、ard was approved by CEN on 5 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning su

7、ch nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language an

8、d notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth

9、erlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in

10、 any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15146:2006: EEN 15146:2006 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Symbols and abbreviations 6 5 Requirements.6 5.1 General6 5.2 Appearance and fini

11、shing.6 5.2.1 General6 5.2.2 Grading classes .7 5.2.3 Free grade.11 5.3 Moisture content11 5.4 Geometrical characteristics11 5.4.1 General11 5.4.2 Profiles11 5.4.3 Dimensions and tolerances 12 5.4.4 Machining .14 5.5 Technical specifications .14 6 Sampling.15 7 Designation 15 Annex A (normative) Sam

12、pling16 Annex B (informative) Principles for the classification of the free grade .17 Bibliography 18 EN 15146:2006 (E) 3 Foreword This document (EN 15146:2006) has been prepared by Technical Committee CEN/TC 175 “Round and sawn timber”, the secretariat of which is held by AFNOR. This European Stand

13、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. This standard is one of a series of standards concerning solid wood panell

14、ing and cladding and wood flooring (including parquet). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germa

15、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 15146:2006 (E) 4 Introduction This standard describes characteristics of solid softwood panelling

16、and cladding based on individual elements. EN 15146:2006 (E) 5 1 Scope This European Standard defines the characteristics of solid wood panelling and cladding without tongue and groove on edges, machined from the following most common European species of softwood: spruce/fir, pine, larch, European D

17、ouglas fir and maritime pine. Products are intended for interior or exterior use. Coatings and finishings are not dealt with in this European Standard. NOTE products sold in the European Economic Area will have to comply with EN 14915. 2 Normative references The following referenced documents are in

18、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 350-2, Durability of wood and wood-based products - Natural durability of solid wood -

19、Part 2: Guide to natural durability and treatability of selected wood species of importance in Europe EN 844-3:1995, Round and sawn timber - Terminology - Part 3: General terms relating to sawn timber EN 844-4:1997, Round and sawn timber - Terminology - Part 4: Terms relating to moisture content EN

20、844-5:1997, Round and sawn timber - Terminology - Part 5: Terms relating to dimensions of round timber EN 844-6:1997, Round and sawn timber - Terminology - Part 6: Terms relating to dimensions of sawn timber EN 844-7:1997, Round and sawn timber - Terminology - Part 7: Terms relating to anatomical st

21、ructure of timber EN 844-8:1997, Round and sawn timber - Terminology - Part 8: Terms relating to features of round timber EN 844-9:1997, Round and sawn timber - Terminology - Part 9: Terms relating to features of sawn timber EN 844-10:1998, Round and sawn timber - Terminology - Part 10: Terms relati

22、ng to stain and fungal attack EN 844-11:1998, Round and sawn timber - Terminology - Part 11: Terms relating to degrade by insects EN 844-12:2000, Round and sawn timber - Terminology - Part 12: Additional terms and general index EN 1309-1:1997, Round and sawn timber- Method of measurement of dimensio

23、ns Part 1: Sawn timber EN 1310:1997, Round and sawn timber - Method of measurement of features EN 13183-1, Moisture content of a piece of sawn timber Part 1: Determination by oven dry method EN 13183-2, Moisture content of a piece of sawn timber Part 2: Estimation by electrical resistance method EN

24、13556, Round and sawn timber Nomenclature of timbers used in Europe EN 13647, Wood and parquet flooring and wood panelling and cladding Determination of geometrical characteristics EN 13756:2002, Wood flooring Terminology EN 15146:2006 (E) 6 3 Terms and definitions For the purposes of this European

25、Standard, the terms and definitions given in EN 13756:2002, EN 844-3:1995, EN 844:1997 parts 4 through 9, EN 844:1998 parts 10 and 11, EN 844-12:2000, EN 1309-1:1997 and the following apply. 3.1 panelling and cladding without tongue and groove boards of solid wood without “tongue and groove” which h

26、ave been machined on the face and two edges. NOTE The back is either machined or hit and/or missed, depending on the product. For special purposes (for instance, acoustic) the edges may have fastening slots. The ends of the boards may be end matched 3.2 end matching any profile for connection at the

27、 end of the panelling or cladding including tongue and/or groove 3.3 panelling elements of solid wood mainly for interior use 3.4 cladding elements of solid wood mainly for exterior use 3.5 face visible surface of an element NOTE Includes edges and chamfer. 4 Symbols and abbreviations Symbols and ab

28、breviations used in this European Standard are given in Figure 1 and in Table 3 and Table 4. 5 Requirements 5.1 General The softwood species shall be selected with regard to the appearance expected, the suitability for the intended purpose and the general characteristics of the species itself. All r

29、equirements apply at the time of production unless the manufacturer states otherwise. 5.2 Appearance and finishing 5.2.1 General Grading applies to the face only, unless otherwise specified. Machining requirements are covered in 5.4.4 and apply to all grades of all species. Natural variation within

30、a single species is generally accepted as a common feature of wood and is not considered for classification of appearance, with the exception of free grade. Measuring features shall be in accordance with EN 1310. Concerning knots the general method in EN 1310:1997, 4.1.1, applies. The boards may be

31、finished with surface coating. The grading shall be done before coating. EN 15146:2006 (E) 7 5.2.2 Grading classes Grading and the features for spruce (Picea spp.) / fir (Abies spp.), pine (Pinus spp.), larch (Larix spp.) and European Douglas Fir (Pseudotsuga menziesii) are given in Table 1. Grading

32、 and the features for Maritima Pine (pinus pinaster) are given in Table 2. For free class, see clause 5.2.3. Table 1 Grading classes of the wood species - Spruces (Picea spp.), fir (Abiea spp.), pine (Pinus spp.), larch (Larix spp.), and European Douglas fir (Pseudotsuga menziesii) Features a b cGra

33、de A Grade B Knots permitted: - black pin knots up to 5 mm if not in clusters; - sound intergrown knots up to 10 % of the width plus 30 mm; - partially intergrown knots, barkringed knots, splay knots and dead knots (not loose); - spruce/fir, and larch: up to 10 % of the width plus15 mm; - pine, and

34、Douglas Fir: up to 10 % of the width plus 30 mm; - occasional small missing and damaged arris knots up to 20 % of the largest acceptable knot size provided coverage is not affected; - knot-plugs of the same wood species, up to the largest allowed knot size. not permitted: - loose knots, knot-holes a

35、nd unsound knots permitted: - black pin knots up to 5 mm; - sound intergrown knots, partially intergrown knots, barkringed knots, splay knots, and dead knots up to 10 % of the width plus 50 mm; - occasional loose knots, knot-holes and unsound knots up to 15 mm; - knot plugs of the same wood species.

36、 (continued) EN 15146:2006 (E) 8 Table 1 Continued Features a b cGrade A Grade B Chipped Grain (machined damaged spots) permitted with knots: up to 20 % of the permitted maximum knot size; with other spots up to 20 % of the maximum knot size (one per m) permitted with knots: up to 40 % of the permit

37、ted maximum knot size; with other spots up to 40 % of the maximum knot size. Compression wood Permitted but see “Deformation” Deformation permitted if correct fastening is possible Stick marks Not permitted permitted Resin pockets permitted: - occasionally up to the size of 2 mm x 25 mm or equal in

38、mm - 1 resin pocket up to the size of 5 mm x 50 mm or equal in mm per 1,5 m in length permitted: - up to the size of 2 mm x 35 mm or equal in mm unlimited - 3 resin pockets up to the width of 6 mm and a total length of 150 mm or equal in mm and per 1,5 m in length Fissures (shakes) permitted: - hair

39、 fissures (barely visible); - end shakes not longer than width of the boards. end shakes: Boards with tongue and groove: Occasionally if not longer than half of the width of the boards not permitted: - fissures (shakes) going through with the exception of end shakes; - fissures extending from face t

40、o edge; - ring shakes; - fissures on the reverse side, continuing for the full length of the board permitted: - face shakes going through (maximum 1 mm wide) up to 300 mm in length; - end shakes not longer than twice the width. end shakes: Boards with tongue and groove: occasionally permitted for th

41、e other boards, it is not permitted: - ring shakes. (continued) EN 15146:2006 (E) 9 Table 1 Concluded Features a b cGrade A Grade B Pith permitted at 1/3 of length not more than 5 mm in width. permitted Colour face side: without any discolouration (discolouration on the reverse side is permitted). p

42、ermitted: slight discolouration as red and blue stain (discolouration on the reverse side is permitted). Fungal attack not permitted not permitted (exception: discolouration - see ”colour“) Insect damages not permitted Wane not permitted on face, permitted on the back side not longer than the width

43、of the board. not permitted on face, permitted on back side up to 1/4 of the length. Ingrown bark permitted: occasional up to the size of 5 mm x 50 mm or equal in mm. permitted aNot more than 5 % of the quantity of the consignment is allowed to be in the next lower grade. Pieces not achieving the re

44、quirements of the B grade must fulfil the principles of panelling and cladding end use. b The classification for appearance does not take into account features which may impair the element when installed. c The face compromises the whole visible surface of the strip when assembled. Therefore extendi

45、ng to the edges and in particular, the chamfers. NOTE For defects not mentioned, assessment should be based on the defined features they most closely resemble. EN 15146:2006 (E) 10 Table 2 Grading classes - Maritime Pine (Pinus pinaster) Features a b cGrade 0 (SN) dGrade A (PN) dGrade B (NO) dKnots

46、permitted: (not considered) knots 2 mm if not grouped together not permitted: other knots and loose knots knot plugs permitted: sound and intergrown knots even slightly checked with a diameter 35 mm but not grouped together black knots (except loose knots) or those having a lack of material on the f

47、ace of a diameter 15 mm knot plugs of the same wood species, up to the largest allowed knot size not permitted: loose knots, unsound knots, knots over limits permitted permitted: knots without limitation in diameter knot plugs of the same wood species not permitted: loose knots, unsound knots Chippe

48、d grain (damage spots) not permitted permitted: with knots up to 20 % of the knot area with other knots up to 20 % of the permitted maximum knot size (one per meter) permitted: with knots up to 40 % of the knot area with other spots up to 40 % of the maximum knot size Compression wood permitted Defo

49、rmation permitted if the correct fastening is possible Resin pockets permitted: l 10 mm permitted: l 70 mm permitted: if not throughout l: no limitation Fissures (Shakes) not permitted permitted: occasional Pith permitted: l 10 mm permitted: l 70 mm permitted: if not throughout l: no limitation Colour face side: without any discolouration (discolouration on the reverse side is permitted) Fungal attack not permitted Insects damages a Not more than 5 % of the quantity of the consignment is allowed to be in the next lower gr