EN 14870-1-2011 en Petroleum and natural gas industries - Induction bends fittings and flanges for pipeline transportation systems - Part 1 Induction bends《石油和天然气工业 管道运输系统的感应管弯头 配件.pdf

《EN 14870-1-2011 en Petroleum and natural gas industries - Induction bends fittings and flanges for pipeline transportation systems - Part 1 Induction bends《石油和天然气工业 管道运输系统的感应管弯头 配件.pdf》由会员分享，可在线阅读，更多相关《EN 14870-1-2011 en Petroleum and natural gas industries - Induction bends fittings and flanges for pipeline transportation systems - Part 1 Induction bends《石油和天然气工业 管道运输系统的感应管弯头 配件.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14870-1:2011Petroleum and natural gasindustries Induction bends,fittings and flanges for pipelinetransportation systemsPart 1: Induction bends (ISO 15590-1:2009modified)BS

2、EN 14870-1:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14870-1:2011.It supersedes BS EN 14870-1:2004 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PSE/17, Materials and equipment for petroleum,petrochemic

3、al and natural gas industries.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 71886 1ICS 2

4、3.040.40; 23.040.60; 75.200Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS EN 14870-1:2011EURO

5、PEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14870-1 June 2011 ICS 23.040.40; 23.040.60; 75.200 Supersedes EN 14870-1:2004English Version Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 m

6、odified) Industries du ptrole et du gaz naturel - Coudes dinduction, raccords et brides pour systmes de transport par conduites - Partie 1: Coudes dinduction (ISO 15590-1:2009 modifie) Erdl- und Erdgasindustrie - Im Induktionsverfahren gefertigte Rohrbgen, Fittings und Flansche fr Rohrleitungs-Trans

7、portsysteme - Teil 1: Im Induktionsverfahren gefertigte Rohrbgen This European Standard was approved by CEN on 10 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wi

8、thout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any othe

9、r language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,

10、Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMA

11、LISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14870-1:2011: EBS EN 14870-1:2011EN 14870-1:2011 (E) 2 Contents Page Foreword 4Introd

12、uction .51 Scope 72 Conformance 72.1 Units of measurement .72.2 Rounding 72.3 Compliance to standard 73 Normative references 84 Terms and definitions 105 Symbols and abbreviated terms . 125.1 Symbols . 125.2 Abbreviated terms 126 Designation . 137 Pressure rating and design . 138 Information that sh

13、all be supplied by the purchaser 148.1 General information 148.2 Additional information . 148.3 Information on the mother pipe . 159 Manufacturing . 159.1 Mother pipe 159.2 Qualification test bend . 169.3 Production bending 169.4 Post-bending heat treatment . 169.5 Forming and sizing after bending .

14、 179.6 Strip/plate end welds 179.7 Jointers and girth welds 179.8 End preparation 1810 Testing and inspection . 1810.1 General requirements . 1810.2 Extent of testing and inspection . 1810.3 Chemical composition . 1810.4 Physical testing. 1910.5 Non-destructive testing 2610.6 Dimensions 2810.7 Gaugi

15、ng . 3110.8 Hydrostatic testing . 3111 Inspection document 3112 Marking 31Annex A (normative) Manufacturing procedure specification 33A.1 Introduction . 33A.2 Manufacturing procedure specification . 33Annex B (normative) PSL 2S bends ordered for sour service 35B.1 Introduction . 35B.2 Additional inf

16、ormation that shall be supplied by the purchaser . 35BS EN 14870-1:2011EN 14870-1:2011 (E) 3 B.3 Manufacturing 35B.4 Testing and inspection . 36B.5 Hard spots 38B.6 Inspection . 38B.7 Non-destructive inspection 38Bibliography 40BS EN 14870-1:2011EN 14870-1:2011 (E) 4 Foreword This document (EN 14870

17、-1:2011) has been prepared by Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries ”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publicati

18、on of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC sh

19、all not be held responsible for identifying any or all such patent rights. This document supersedes EN 14870-1:2004. The text of ISO 15590-1:2009 has been adopted by CEN/TC 12 with some modifications. These modifications are indicated by a vertical line in the left margin of the text. Where the expr

20、ession “International Standard” is used, it is understood as “European Standard”. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Repub

21、lic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 14870-1:2011EN 14870-1:2011 (E) 5 Introduction

22、 This International Standard makes reference to line pipe and bends with delivery conditions based on ISO 3183. Following significant revision of ISO 3183 (ISO 3183:2007), ISO 15590-1 has been reviewed and redrafted taking cognizance of the changes to ISO 3183. In addition to general revision, and i

23、n common with ISO 3183:2007, the Technical Committee has introduced additional requirements for special applications as follows: Manufacturing procedure specification (Annex A); PSL 2 bends for sour service (Annex B). The requirements of the annexe(s) apply only when it is (they are) specified on th

24、e purchase order. This International Standard does not provide guidance on when it is necessary to specify the above supplementary requirements. Instead it is the responsibility of the purchaser to specify, based upon the intended use and design requirements, which, if any, of the supplementary requ

25、irements apply for a particular purchase order. Users of ISO 15590 need to be aware that further or differing requirements can be needed for individual applications. This part of ISO 15590 is not intended to inhibit a manufacturer from offering, or the purchaser from accepting, alternative equipment

26、 or engineering solutions for the individual application. This can be particularly applicable where there is innovative or developing technology. Where an alternative is offered, it is the responsibility of the manufacturer to identify any variations from this part of ISO 15590 and provide details.

27、ISO 15590 consists of the following parts, under the general title Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems: Part 1: Induction bends; Part 2: Fittings; Part 3: Flanges. ISO 15590-1:2009, developed within ISO/TC 67/SC2, has been ad

28、opted as EN 14870-1:2011 (ISO 15590-1:2009 modified). The scope of ISO/TC 67/SC2 is pipeline transportation systems for the petroleum and natural gas industries without exclusions. However in CEN, the scopes of CEN/TC 12 and CEN/TC 234 overlapped until 1995. This scope overlap caused problems for th

29、e parallel procedure for the above-mentioned items. The conflict in scope was resolved when both the CEN/Technical Committees and the CEN/BT took the following resolution: Resolution BT 38/1995: Subject: Revised scope of CEN/TC 12 “BT endorses the conclusions of the coordination meeting between CEN/

30、TC 12 “Materials, equipment and offshore structures for petroleum and natural gas industries” and CEN/TC 234 “Gas supply” and modifies the CEN/TC 12 scope, to read: “Standardization of the materials, equipment and offshore structures used in drilling, production, refining and the transport by pipeli

31、nes of petroleum and natural gas, excluding on-land supply systems used by the gas supply industry and those aspects of offshore structures covered by IMO requirement (ISO/TC 8). The standardization is to be achieved wherever possible by the adoption of ISO Standards.” In 2009, CEN/TC 12 changed its

32、 scope to be in coherency with the last CEN/TC 234s scope changes, as follows (resolution CEN/BTC 19/2009): BS EN 14870-1:2011EN 14870-1:2011 (E) 6 Standardisation of the materials, equipment and offshore structures used in the drilling, production, transport by pipelines and processing of liquid an

33、d gaseous hydrocarbons within the petroleum, petrochemical and natural gas industries, excluding on-land supply systems used by the gas supply industry excluding gas infrastructure from the input of gas into the on-shore transmission network up to the inlet connection of gas appliances. (covered by

34、CEN/TC 234) and those aspects of offshore structures covered by IMO requirements (ISO/TC 8). The standardisation is to be achieved wherever possible by the adoption of ISO standards. Resulting from these resolutions, “on-land supply systems used by the gas supply industry excluding gas infrastructur

35、e from the input of gas into the on-shore transmission network up to the inlet connection of gas appliances “ has been excluded from the scope of ISO 15590-1:2009 for the European adoption by CEN/TC 12. BS EN 14870-1:2011EN 14870-1:2011 (E) 7 1 Scope This International Standard specifies the technic

36、al delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623. This International Standard is applicable to induction bends made from seamless and welded pipe of unalloyed or low-

37、alloy steels. NOTE These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183. This International Standard specifies the requirements for the manufacture of two product specification levels (PSLs) of inducti

38、on bend corresponding to product specification levels given for pipe in ISO 3183. This International Standard is not applicable to the selection of the induction bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design req

39、uirements; see also ISO 3183:2007, Introduction. This International Standard is not applicable to pipeline bends made by other manufacturing processes. On-land supply systems used by the gas supply industry excluding gas infrastructure from the input of gas into the on-shore transmission network up

40、to the inlet connection of gas appliances are excluded from the scope of this standard. 2 Conformance 2.1 Units of measurement In this International Standard, data are expressed in both SI units and USC units. For a specific order item, unless otherwise stated, only one system of units shall be used

41、, without combining data expressed in the other system. For data expressed in SI units, a comma is used as the decimal separator and a space is used as the thousands separator. For data expressed in USC units, a dot (on the line) is used as the decimal separator and a space is used as the thousands

42、separator. 2.2 Rounding Unless otherwise stated in this International Standard, to determine conformance with the specified requirements, observed or calculated values shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance wi

43、th ISO 80000-1:2009, Annex B, Rule A. NOTE For the purposes of this provision, the rounding method of ASTM E29-041is equivalent to ISO 80000-1:2009, Annex B, Rule A. 2.3 Compliance to standard A quality management system should be applied to assist compliance with the requirements of this Internatio

44、nal Standard. NOTE ISO/TS 290014gives sector-specific guidance on quality management systems. BS EN 14870-1:2011EN 14870-1:2011 (E) 8 A contract may specify that the manufacturer shall be responsible for complying with all of the applicable requirements of this International Standard. It shall be pe

45、rmissible for the purchaser to make any investigation necessary in order to be assured of compliance by the manufacturer and to reject any material that does not comply. 3 Normative references The following referenced documents are indispensable for the application of this document. For dated refere

46、nces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method EN ISO 6507 (all parts), Metallic materials Vickers hardness test EN ISO 65

47、08 (all parts), Metallic materials Rockwell hardness test EN ISO 6892(all parts), Metallic materials Tensile testing EN ISO 7438, Metallic materials Bend test (ISO 7438:2005) EN ISO 7539-2, Corrosion of metals and alloys Stress corrosion testing Part 2: Preparation and use of bent-beam specimens(ISO

48、 7539-2:1989) ISO 783, Metallic materials Tensile testing at elevated temperature ISO 3183:2007, Petroleum and natural gas industries Steel pipe for pipeline transportation systems ISO 8501-1:2007, Preparation of steel substrates before application of paints and related products Visual assessment of

49、 surface cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings(ISO 8501-1:2007) ISO 9303:1989, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of longitudinal imperfections ISO 9305, Seamless steel tubes for pressure purposes Full peripheral ultra