EN 14691-2005 752 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Compatibility by heat conditionin.pdf

《EN 14691-2005 752 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Compatibility by heat conditionin.pdf》由会员分享，可在线阅读，更多相关《EN 14691-2005 752 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Compatibility by heat conditionin.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 14691:2005Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Compatibility by heat conditioningThe European Standard EN 14691:2005 has the status of a British StandardICS 91.100.50g49g50g3g38g50g51g60g44g

2、49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or netw

3、orking permitted without license from IHS-,-,-BS EN 14691:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2005 BSI 31 October 2005ISBN 0 580 46613 2National forewordThis British Standard is the official English language version

4、 of EN 14691:2005.The UK participation in its preparation was entrusted by Technical Committee B/546, Flexible sheets for waterproofing and water vapour control, to Subcommittee B/546/9, Bridge deck waterproofing, which has the responsibility to: aid enquirers to understand the text; present to the

5、responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this subcommittee can be obtaine

6、d on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of th

7、e BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a cotnract. Users are respondible for its correct applicatin.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of

8、pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright date displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsCopyright E

9、uropean Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14691May 2005ICS 91.100.50English versionFlexible sheets for waterproofing - Waterproofing

10、of concretebridge decks and other concrete surfaces trafficable by vehicles- Compatibility by heat conditioningFeuilles souples dtanchit - Etanchit de ponts etautres surfaces en bton circulables par les vhicules -Dtermination de la compatibilit au conditionnementthermiqueAbdichtungsbahnen - Abdichtu

11、ngen fr Betonbrcken undandere Verkehrsflchen auf Beton - Bestimmung derVertrglichkeit nach WrmelagerungThis European Standard was approved by CEN on 17 April 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard

12、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, Germa

13、n). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark

14、, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES

15、KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14691:2005: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for

16、 ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14691:2005 (E) 2 Contents page Foreword 3 Introduction . 4 1 Scope. 5 2 Normative references. 5 3 Terms and definitions 5 4 Test methods 5 4.1 Principle 5 4.2 Apparatus 5 4.3 Preparation of the test specimen 6 4.4 Procedu

17、re 6 4.5 Expression of results . 6 4.6 Test report. 6 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14691:2005 (E) 3 Foreword This document (EN 14691:2005) has been prepared

18、 by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2005, and conflicting nati

19、onal standards shall be withdrawn at the latest by November 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra

20、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resal

21、eNo reproduction or networking permitted without license from IHS-,-,-EN 14691:2005 (E) 4 Introduction The purpose of the test is to determine the compatibility of the waterproofing system in the installed condition by determination of the shear strength properties before and after accelerated heat

22、conditioning. Waterproofing systems are required to maintain performance over extended periods of time once installed on a concrete structure. Many flexible sheets used in the waterproofing of concrete bridge decks are based on materials that are subject to oxidation, migration, diffusion, and absor

23、ption of components within the system itself and/or those to which the system is adhered. These physico-chemical effects occur over time, however increased temperature will accelerate these effects. The use of an accelerated heat-conditioning test will allow the evaluation of the change in a specifi

24、c mechanical property, shear strength, over a significantly shorter time period than allowing the waterproofing system to age under normal ambient conditions. The use of the shear resistance test will allow the determination of any change in properties together with an indication of any migrational

25、or interfacial long term incompatibility between the adherents. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14691:2005 (E) 5 1 Scope This European Standard specifies a tes

26、t method for the evaluation of the compatibility of the waterproofing system applied to a concrete surface and covered with an asphalt layer. The complete system is exposed to an accelerated heat conditioning followed by a determination of the shear strength properties before and after heat conditio

27、ning. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13375:2004, Flexi

28、ble sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Specimen preparation EN 13416:2001, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling EN 13653, Flexible sheets for

29、 waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of shear strength prEN 14695:2003, Flexible sheets for waterproofing Reinforced bitumen sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficabl

30、e by vehicles Definitions and characteristics 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 13416:2001, EN 13375:2004, prEN 14695:2003, and the following apply. heat conditioning process whereby the test specimen is held at an elevated temp

31、erature for a specified period of time 4 Test methods 4.1 Principle To detect by a change of the shear resistance if any changes occur in properties of test specimens when they are subjected to accelerated heat conditioning. This is achieved by testing a set of test specimens that have been heat con

32、ditioned and comparing the results with a reference set of test specimens that have not been heat conditioned. 4.2 Apparatus a) Oven, with circulating air (without fresh supply), capable of maintaining (50 2) C. b) Loading and support device, capable of meeting the requirements set out in EN 13653.

33、Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 14691:2005 (E) 6 4.3 Preparation of the test specimen Prepare the test specimens (Type 3) in accordance with EN 13375 for the t

34、est method according to EN 13653, and cool to room temperature. Four test specimens are used for the heat conditioning, and four reference test specimens are used for comparison. 4.4 Procedure 4.4.1 Condition the four reference test specimens at (23 2) C for at least 24 h prior to them being tested

35、in accordance with EN 13653. 4.4.2 Place the remaining four test specimens horizontally in an air-circulating oven in such a way as to allow free movement of air over and around the test specimen. Maintain the temperature in the oven at (50 2) C. Ensure that the test specimens are not stacked on top

36、 of each other. 4.4.3 Remove the test specimens from the oven after a period of 91 days, and allow to condition at (23 2) C for 24 h prior to being tested for shear strength in accordance with EN 13653. 4.4.4 Before and after the test for shear strength, visually inspect the test specimens for evide

37、nce of migration and separation of component layers. NOTE Migration and separation can take the form of a build up of a semi liquid layer at the interfaces of the waterproofing systems. 4.5 Expression of results The results shall be expressed in accordance with EN 13653. Compatibility C (%) is expre

38、ssed by: 10010maxmax0max =CC where max o= mean value of shear strength of reference test specimens max C=mean value of shear strength of conditioned specimens NOTE There is no precision data currently available for this test method. 4.6 Test report The test report shall include at least the followin

39、g information: a) all details necessary to identify the product tested; b) reference to this European Standard and any deviation from it; c) information about preparation of test specimens in accordance with 4.3; d) information about the procedure in accordance with 4.4; e) test result with the forc

40、e displacement plot and failure mode for each individual shear test according to 4.4 and compatibility in accordance with 4.5; f) visual inspection of the condition of the conditioned test specimen as compared with the control; g) dates of delivery and preparation of specimens; h) date of tests. Cop

41、yright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-blankCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networki

42、ng permitted without license from IHS-,-,-BS EN 14691:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incor

43、porated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

44、finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service c

45、alled PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Stand

46、ards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of

47、information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111.

48、 Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the B