EN 14399-1-2005 5898 High-strength structural bolting assemblies for preloading - Part 1 General requirements《预加负荷用高强度结构螺栓组件 第1部分 一般要求》.pdf

《EN 14399-1-2005 5898 High-strength structural bolting assemblies for preloading - Part 1 General requirements《预加负荷用高强度结构螺栓组件 第1部分 一般要求》.pdf》由会员分享，可在线阅读，更多相关《EN 14399-1-2005 5898 High-strength structural bolting assemblies for preloading - Part 1 General requirements《预加负荷用高强度结构螺栓组件 第1部分 一般要求》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58preloading Part 1: General requirementsThe European Standard EN 14399-1:2005 has the status of a Br

2、itish StandardICS 21.060.01High-strength structural bolting assemblies for BRITISH STANDARDBS EN 14399-1:2005BS EN 14399-1:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 7 October 2005 BSI 7 October 2005ISBN 0 580 46543 8National forewor

3、dThis British Standard is the official English language version of EN 14399-1:2005.EN 14339-1:2005 is a candidate “harmonized” European Standard and fully takes into account the requirements of the European Commission mandate M/120, Structural metallic products and ancillaries, given under the EU Co

4、nstruction Products Directive (89/106/EEC), and is intended to lead to CE marking. The date of applicability of EN 14399-1:2005 as a harmonized European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official Journal of the

5、 European Communities.The Commission in consultation with Member States has agreed a transition period for the co-existence of harmonized European Standards and their corresponding national standard(s). It is intended that this period will comprise a period, usually nine months, after the date of av

6、ailability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usually of 12 months, for the implementation of CE marking. In this instance an application has been made to CEN for a two-year extended co-existence period, f

7、rom September 2005 to September 20071). At the end of the co-existence period, the national standard(s) will be declared obsolescent, and will be withdrawn on publication of Eurocode 3.EN 14399-1:2005 is the subject of transitional arrangements agreed under the Commission mandate. In the UK, the cor

8、responding national standards are: BS 4395-1:1969, Specification for high strength friction grip bolts and associated nuts and washers for structural engineering Part 1: General grade; BS 4395-2:1969, Specification for high strength friction grip bolts and associated nuts and washers for structural

9、engineering Part 2: Higher grade bolts and nuts and general trade washers2);and based on the applied-for transition period, it is planned that BS 4395-1:1969 and BS 4395-2:1969 will be declared obsolescent in September 20071), and then, together with BS 449 and BS 5950, will be withdrawn upon public

10、ation of Eurocode 3. BS 4395-1:1969 and BS 4395-2:1969 currently support BS 449 and BS 5950.NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation of withdrawal.1)CEN/TC 185/WG 6 has applied for a two-year extended co-existence period, to “Septemb

11、er 2007”, and for a corrigendum to amend the second “September 2005” date in the Foreword to EN 14399-1:2005 to “September 2007”.2)Together with BS EN 14399-2:2005, BS EN 14399-3:2005, BS EN 14399-4:2005, BS EN 14399-5:2005 and BS EN 14399-6:2005, BS EN 14399-1:2005 supersedes BS 4395-1:1969 and BS

12、4395-2:1969.Summary of pagesThis document comprises a front cover, page i, a blank page, an inside front cover, the EN title page, pages 2 to 22, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued si

13、nce publicationAmd. No. Date CommentsBS EN 14399-1:2005The UK participation in the preparation of EN 14399-1 was entrusted by Technical Committee FME/9, Nuts, bolts and accessories/Steering Committee, to its Subcommittee, FME/9/1, Materials, which has the responsibility to:A list of organizations re

14、presented on this subcommittee can be obtained on request to its secretary.Additional InformationThis part of BS EN 14399 is one of several parts that comprise the BS EN 14399 series of standards. BS EN 14399-1 provides the general requirements to which the other parts, which provide specific requir

15、ements regarding manufacture, materials and testing, relate.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by usi

16、ng the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity fro

17、m legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.i

18、blankEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14399-1March 2005ICS 21.060.01English versionHigh-strength structural bolting assemblies for preloading - Part1: General requirementsBoulonnerie de construction mtallique haute rsistanceapte la prcontrainte - Partie 1: Exigences gnralesGarniture

19、n fr hochfeste planmig vorspannbareSchraubenverbindungen fr den Metallbau - Teil 1:Allgemeine AnforderungenThis European Standard was approved by CEN on 3 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanSt

20、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French,

21、 German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, D

22、enmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPI

23、SCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14399-1:2005: EEN 14399-1:2005 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative re

24、ferences 5 3 Terms and definitions .5 4 Requirements.6 5 Testing for conformity evaluation9 6 Evaluation of conformity.11 7 Documentation of test results16 Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive (89/106/EEC).17 Bibliog

25、raphy 22 EN 14399-1:2005 (E) 3 Foreword This document (EN 14399-1:2005) has been prepared by Technical Committee CEN/TC 185, “Threaded and non-threaded mechanical fasteners and accessories“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national stand

26、ard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the lat-est by September 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Tr

27、ade Association, and supports essential requirements of EC Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document includes a Bibliography According to the CEN/CENELEC Internal Regulations, the national standards organi

28、zations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Esto-nia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, S

29、lovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14399-1:2005 (E) 4 Introduction This document on structural bolting reflects the situation in Europe where two technical solutions exist to achieve the necessary ductility of bolt/nut/washer assemblies. These solutions utilize different syst

30、ems (HR and HV) of bolt/nut/washer assemblies, see Table 1. Both systems are well proved and it is up to the experts responsible for structural bolting whether they use the one or the other system. It is, however, important for the performance of the assembly to avoid mixing up the components of bot

31、h systems. Therefore, the bolts and nuts for both systems are standardized in one single part of this European Standard each and the marking of the components of the same system is uniform. Table 1 Systems of bolt/nut/washer assemblies Bolt/nut/washer assembly System HR Bolt/nut/washer assembly Syst

32、em HV General require-ments EN 14399-1 Bolt/nut assembly EN 14399-3 EN 14399-4 Marking HR HV Property classes 8.8/8 10.9/10 10.9/10 Washer(s) EN 14399-5 or EN 14399-6 EN 14399-5 or EN 14399-6 Marking H H Suitability test for preloading EN 14399-2 EN 14399-2 Preloaded bolted assemblies are very sensi

33、tive to differences in manufacture and lubrication. Therefore it is important that the assembly is supplied by one manufacturer who is always responsible for the function of the assembly. For the same reason it is important that coating of the assembly is under the control of one manufacturer. Besid

34、e the mechanical properties of the components the functionality of the assembly requires that the specified preload can be achieved if the assembly is tightened with a suitable procedure. For this purpose a test method for the suitability of the components for preloading was created which will demon

35、strate whether the function of the assembly is fulfilled. For the time being, the product standards EN 14399-3 to EN 14399-6 are the only European Standards which have regard to the general requirements of EN 14399-1. However, further product standards on fit bolts, countersunk head bolts, and load

36、indicating washers for the use in high strength structural bolting for preloading are under preparation. EN 14399-1:2005 (E) 5 1 Scope This document specifies the general requirements for the components of bolt/nut/washer(s) assemblies for high-strength structural bolting, which are suitable for pre

37、loading, and for the assemblies themselves. Examples for components which fulfil the requirements of this document are specified in EN 14399-3, EN 14399-4, EN 14399-5 and EN 14399-6. NOTE For clauses of this document addressing the provisions of the EU Construction Products Directive, see Annex ZA.

38、2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ENV 1090-1:1996, Execution

39、 of steel structures Part 1: General rules and rules for buildings. EN 10045-1, Metallic materials Charpy impact test Part 1: Test method. EN 10204, Metallic products Types of inspection documents. EN 14399-2, High-strength structural bolting for preloading Part 2: Suitability test for preloading. E

40、N 14399-3, High-strength structural bolting for preloading Part 3: System HR Hexagon bolt and nut assem-blies. EN 14399-4, High-strength structural bolting for preloading Part 4: System HV Hexagon bolt and nut assem-blies. EN 14399-5, High-strength structural bolting for preloading Part 5: Plain was

41、hers. EN 14399-6, High-strength structural bolting for preloading Part 6: Plain chamfered washers. EN 20225, Fasteners Bolts, screws, studs and nuts Symbols and designation of dimensions (ISO 225:1983). EN 20898-2, Mechanical properties of fasteners Part 2: Nuts with specified proof load values Coar

42、se thread (ISO 898-2:1992). EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs (ISO 898-1:1999). EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method (ISO 6507-1:1997). EN ISO 9001, Quality management systems R

43、equirements (ISO 9001:2000). 3 Terms and definitions For the purposes of this document, the terms and definitions given in Guide to the Implementation of Directives Based on the New Approach and Global Approach and ENV 1090-1:1996 and the following apply. 3.1 assembly comprises matching bolt, nut an

44、d necessary washer(s) EN 14399-1:2005 (E) 6 3.2 manufacturing lot quantity of fasteners of a single designation including product grade, property class and size1), manufactured from bar, wire, rod or flat product from a single cast, processed through the same or similar steps at the same time or ove

45、r a continuous time period through the same heat treatment and/or coating process, if any NOTE 1 Same heat treatment or coating process means: for a continuous process, the same treatment cycle without any setting modification; for a discontinuous process, the same treatment cycle for identical cons

46、ecutive loads (batches). NOTE 2 The manufacturing lot may be split into a number of manufacturing batches for processing purposes and then reas-sembled into the same manufacturing lot. NOTE 3 Adapted from ISO 15330. 3.3 assembly lot assemblies supplied together as a set comprising: bolts from a sing

47、le manufacturing lot; nuts from a single manufacturing lot; washers from a single manufacturing lot 3.4 extended assembly lot manufacturing lot of that component that mainly influences the result of the suitability test combined with the other components from the same supplier chosen by a documented

48、 method NOTE The component with the main influence is determined on the basis of test results. 4 Requirements 4.1 Ordering information At the time of order the manufacturer shall obtain the following information: a) the quantities to be delivered, b) the product designation, c) the k-class according

49、 to 4.4.4; if no k-class is specified, k-class K0 applies, d) Others requirements as agreed between the supplier and purchaser (for example: low temperature require-ments), in so far they do not conflict with regulatory requirements. 4.2 Manufacturing process 4.2.1 Dangerous substances Materials used in products shall not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in