EN 716-2-2017 en Furniture - Children-s cots and folding cots for domestic use - Part 2 Test methods.pdf

《EN 716-2-2017 en Furniture - Children-s cots and folding cots for domestic use - Part 2 Test methods.pdf》由会员分享，可在线阅读，更多相关《EN 716-2-2017 en Furniture - Children-s cots and folding cots for domestic use - Part 2 Test methods.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、Furniture Childrens cots and folding cots for domestic usePart 2: Test methodsBS EN 7162:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 716-2 June 2017 ICS 97.140; 97.190 Supersedes EN 716-2:2008+A1:2013Englis

2、h Version Furniture - Childrens cots and folding cots for domestic use - Part 2: Test methods Mbel - Kinderbetten und Reisekinderbetten fr den Wohnbereich - Teil 2: Prfverfahren This European Standard was approved by CEN on 21 February 2016. CEN members are bound to comply with the CEN/CENELEC Inter

3、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

4、CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official ver

5、sions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

6、 Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of

7、exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 716-2:2017 ENational forewordThis British Standard is the UK implementation of EN 7162:2017. It supersedes BS EN 7162:2008+A1:2013, which is withdrawn.The UK participation in its preparation was entrus

8、ted to Technical Committee CW/1, Safety of child use and child care products.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correc

9、t application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 90924 5ICS 97.140; 97.190Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and St

10、rategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 7162:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 716-2 June 2017 ICS 97.140; 97.190 Supersedes EN 716-2:2008+A1:2013English Version Furniture - Childrens cots and fol

11、ding cots for domestic use - Part 2: Test methods Mbel - Kinderbetten und Reisekinderbetten fr den Wohnbereich - Teil 2: Prfverfahren This European Standard was approved by CEN on 21 February 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditio

12、ns for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in

13、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standard

14、s bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia

15、, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means re

16、served worldwide for CEN national Members. Ref. No. EN 716-2:2017 EBS EN 7162:2017EN 716-2:2017 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 General test conditions . 5 3.1 Preliminary preparation 5 3.2 Test equipment 5 3.3 Application of forces 6 3.4 Tolerances . 6

17、 3.5 Test sequence . 6 3.6 Prevention of movement during test . 6 4 Test apparatus 6 4.1 Measuring probes . 6 4.2 Bottom impactor . 7 4.3 Test mattress 8 4.4 Side impactor 8 4.5 Loading pad . 9 4.6 Stops . 9 4.7 Floor surface . 9 4.8 Test chain and mass . 9 4.9 Small parts cylinder . 9 4.10 Test mas

18、s . 10 4.11 Bite tester 10 4.12 Retaining block . 11 4.13 Foothold template 11 4.14 Head probes . 12 4.14.1 Small head probe 12 4.14.2 Large head probe . 12 4.15 Template for V-shaped openings 13 4.16 Test dummy 14 5 Test procedures 14 5.1 Assembly and inspection . 14 5.2 Stability - test . 14 5.3 F

19、ootholds . 15 5.3.1 Determination of a foothold . 15 5.3.2 Tests for footholds . 16 5.3.3 Measurement of distance between footholds and/or top of cot sides and ends . 19 5.4 Measurements . 20 5.4.1 Holes, gaps and openings inside the cot 20 5.4.2 Holes, gaps and openings on the outside of the cot .

20、21 5.5 Small parts 23 5.5.1 General . 23 5.5.2 Torque test . 23 5.5.3 Tension test 24 5.6 Bite test 24 5.7 Tests for cot base and mattress base 24 BS EN 7162:2017EN 716-2:2017 (E) 3 5.7.1 Folding test of the mattress base and cot base 24 5.7.2 Strength of cot base and mattress base (impact test) . 2

21、5 5.8 Strength of sides and ends . 26 5.8.1 Static load test of slats (bending test) . 26 5.8.2 Strength of sides or side slats (impact test) 26 5.8.3 Strength of corners (impact test) 27 5.8.4 Strength of mesh and flexible sides and ends (static load test) . 28 5.9 Strength of frame and fastenings

22、28 5.9.1 Vertical static load test . 28 5.9.2 Durability test 29 5.10 Snag points 30 5.11 Locking systems 30 5.11.1 Durability. 30 5.11.2 Strength 30 5.12 Stability test 30 6 Test report 31 Annex A (informative) Adeviations . 32 Bibliography . 33 BS EN 7162:2017EN 716-2:2017 (E) 4 European foreword

23、This document (EN 716-2:2017) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 201

24、7, and conflicting national standards shall be withdrawn at the latest by December 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent right

25、s. This document supersedes EN 716-2:2008+A1:2013. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. Compared to EN 716-2:2008+A1:2013, the following modifications have been made: introduction of the elements of the amend

26、ment; modification of the wrong references to clauses; clarification of 4.3, “Test mattress”; modification of 5.7.1, “Folding test of the mattress base and cot base”. EN 716, Furniture Childrens cots and folding cots for domestic use, is composed with the following parts: Part 1: Safety requirements

27、; Part 2: Test methods. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic o

28、f Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 7162:2017EN 716-2:2017 (E) 5 1 Scope This Europea

29、n Standard specifies test methods for assessing the safety of childrens cots and folding cots for domestic use. It applies to childrens cots and folding cots with an internal length greater than 900 mm but not more than 1 400 mm. 2 Normative references The following documents, in whole or in part, a

30、re normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 2439:2008, Flexible cellular polymeric material

31、s Determination of hardness (indentation technique) (ISO 2439:2008) ISO 7619-2, Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 2: IRHD pocket meter method 3 General test conditions 3.1 Preliminary preparation The tests are designed to be applied to a cot that is fully

32、 assembled and ready for use. The test unit shall be stored in indoor ambient conditions for at least one week immediately prior to testing. Any deviation from this procedure shall be stated in the test report. Before testing, any fabrics intended to be removable shall be cleaned or washed twice in

33、accordance with the manufacturers instructions. If no instructions are supplied, the manner of washing/cleaning shall be stated in the test report. The tests shall be carried out under indoor ambient conditions, but if during a test the atmospheric temperature is outside the range 15 C to 25 C, the

34、maximum and/or minimum temperature shall be recorded in the test report. The cot shall be tested as delivered. If the cot is a knock down type, it shall be assembled according to the manufacturers instructions supplied with the cot. If the cot can be assembled, combined or adjusted in different ways

35、, the most adverse combination shall be used for each test. Knock-down fittings shall be tightened before testing. Further re-tightening shall not take place unless this is specifically required by the manufacturer. In the case of designs not catered for in the test procedures, the tests shall be ca

36、rried out as far as possible as described, and a list made of the deviations from the test procedures. 3.2 Test equipment Unless otherwise specified, the tests may be applied by any suitable device because results are dependent only upon correctly applied forces and loads and not upon the apparatus.

37、 The equipment shall not inhibit the deformation of the cot during testing. It shall be able to move so that it can follow the deformation of the cot during testing, so that the loads are always applied at the specified point and in the specified direction. All loading pads shall be capable of pivot

38、ing in relation to the direction of the applied force. The pivot point shall be as close as practically possible to the load surface. BS EN 7162:2017EN 716-2:2017 (E) 6 3.3 Application of forces The forces in the static load tests shall be applied sufficiently slowly enough to ensure that negligible

39、 dynamic force is applied. The forces in durability tests shall be applied at a rate to ensure that excessive heating does not occur. 3.4 Tolerances Unless otherwise stated, the following tolerances apply: Forces: 5 % of the nominal force; Masses: 0,5 % of the nominal mass; Dimensions: 1,0 mm of the

40、 nominal dimension; Angles: 2 of the nominal angle; Positioning of loading pads: 5 mm; Duration of forces: (2 1) s for durability tests (10 2) s for static load tests, including tension, torque and bite tests. The tests are described in terms of the application of forces. Masses can, however, be use

41、d. The relationship 10 N = 1 kg shall be used for this purpose. 3.5 Test sequence The tests shall be carried out in the order laid down in this standard and on the same cot. 3.6 Prevention of movement during test If the cot tends to slide or roll during the tests specified in Clause 5, it shall be r

42、estrained by stops (4.6). 4 Test apparatus 4.1 Measuring probes Probes made of plastics or other hard, smooth material mounted on a force-measuring device. There shall be one probe with a diameter of 7 mm (0,1/+0 mm), see Figure 1 a). There shall be five probes with an angle of 30 0,5 with diameters

43、 of 25 mm (0/+0,1 mm), 45 mm (0/+0,1 mm), 60 mm (0/+0,1 mm), 65 mm (0/+0,1 mm) and 85 mm (0/+0,1 mm) with conical ends, see Figure 1 b). There shall be four cylindrical probes with diameters of 5 mm (0,1/+0 mm), 7 mm (0,1/+0 mm), 12 mm (0/+0,1 mm) and 18 mm (0/+0,1 mm) with hemispherical ends, see F

44、igure 1 c). BS EN 7162:2017EN 716-2:2017 (E) 7 Dimensions in millimetres a) 7 mm probe b) Conical probes c) Cylindrical probes Key 1 5 mm (0,1/+0 mm), 7 mm (0,1/+0 mm), 12 mm (0/+0,1 mm), 18 mm (0/+0,1 mm) Figure 1 Measuring probes 4.2 Bottom impactor An impactor with a total mass of 10 kg of hardwo

45、od or equivalent material with a hemispherical end and with dimensions in accordance with Figure 2. The impactor shall be guided so that it is kept vertical and always falls on the impact point. Dimensions in millimetres Figure 2 Bottom impactor BS EN 7162:2017EN 716-2:2017 (E) 8 4.3 Test mattress A

46、 polyurethane foam sheet with a thickness of 60 mm, a bulk density of 35 kg/m3 10 % or an indentation hardness index of (170 40) N in accordance with EN ISO 2439:2008, A.40 and being at least 400 mm 800 mm in area but not larger than the mattress base of the cot under test. The test mattress shall h

47、ave a light soft cotton cover with a mass not greater than 120 g/m2. 4.4 Side impactor A pendulum with a cylindrical head made of steel (Figure 3). The head of the pendulum shall be surrounded by a 10 mm thick layer of rubber of hardness 76 IRHD to 78 IRHD in accordance with ISO 7619-2. The total ma

48、ss shall be 2 kg. Dimensions in millimetres Key 1 pivot point 2 centre of gravity 3 rubber 76 to 78 IRHD Figure 3 Side impactor BS EN 7162:2017EN 716-2:2017 (E) 9 4.5 Loading pad A rigid cylindrical object, 100 mm in diameter, having a smooth hard surface and rounded edge with radius of 12 mm. 4.6 S

49、tops Stops which prevent the article from sliding but not tilting, not higher than 12 mm except in cases where the design of the item necessitates the use of higher stops, in which case the lowest that will prevent the item from sliding shall be used. 4.7 Floor surface Rigid, horizontal and flat surface. 4.8 Test chain and mass Ball chain with a ball diameter of (3,2 0,2) mm and a distance between ball centres of (4,0 0,2) mm (Figure 4), fixed to a 2,5 kg spherical weig