EN 6094-2016 en Aerospace series - Washer spring countersunk《航空航天系列-垫圈 弹簧 钻孔装埋》.pdf

《EN 6094-2016 en Aerospace series - Washer spring countersunk《航空航天系列-垫圈 弹簧 钻孔装埋》.pdf》由会员分享，可在线阅读，更多相关《EN 6094-2016 en Aerospace series - Washer spring countersunk《航空航天系列-垫圈 弹簧 钻孔装埋》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 6094:2016Aerospace series Washer,spring, countersunkBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 6094:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 6094:2016.The UK participation in its preparation was entru

2、sted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correcta

3、pplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 92620 4ICS 49.030.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Com

4、mittee on 30 September 2016.Amendments issued since publicationDate Text affectedBS EN 6094:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6094 August 2016 ICS 49.030.50 English Version Aerospace series - Washer, spring, countersunk Srie arospatiale - Rondelle, ressort, fraise Luft- und Ra

5、umfahrt - Federsenkscheibe This European Standard was approved by CEN on 11 March 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date list

6、s and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

7、the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yug

8、oslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPE

9、N DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6094:2016 EBS EN 6094:2016EN 6094:2016 (E) 2 Contents Page Euro

10、pean foreword 3 1 Scope 4 2 Normative references 4 3 Requirements 5 4 Designation 6 5 Marking . 7 6 Technical specification 7 7 Example of installation 7 Bibliography . 8 BS EN 6094:2016EN 6094:2016 (E) 3 European foreword This document (EN 6094:2016) has been prepared by the Aerospace and Defence I

11、ndustries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentati

12、on to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by February 2017. Attention is drawn to the possibilit

13、y that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bou

14、nd to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

15、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6094:2016EN 6094:2016 (E) 4 1 Scope This European Standard specifies the dimensions, tolerances, required characteristics and mass of a countersunk spring washer for use in fuselage interior equipment an

16、d structural applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

17、cument (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2516, Aerospace series Passivation of corrosion resistant steels and decontamination of nickel base alloys EN 2540, Aerospace series Steel FE-PM3902 (X7CrNiAl17-7) air melted, solution treated and p

18、recipitation hardened Sheet and strip, a 6 mm, 1240 MPa Rm 1450 MPa1)EN 6088, Aerospace series Stud1)EN 6092, Aerospace series Receptacle, floating, double lug1)EN 6093, Aerospace series Receptacle, floating, single lug1)EN 6095, Aerospace series Rotary fasteners Structural and non-structural applic

19、ations Technical specification1)EN 6105, Aerospace series Stud with shoulder1)EN 10088-2, Stainless steels Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimen

20、sions without individual tolerance indications SAE AMS 2700, Passivation of corrosion resistant steels2)1)Published as ASD Prestandard at the date of publication of this standard. 2)Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. BS EN 609

21、4:2016EN 6094:2016 (E) 5 3 Requirements 3.1 Configuration, dimensions, tolerances and mass The configuration, dimensions, tolerances and mass shall conform with Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres. Tolerances not specified shall be in accordance with ISO 2768

22、-1. All dimensions and tolerances apply after surface treatment. All burrs to be removed / sharp edges to be broken. Figure 1 Configuration Table 1 Dimensions and mass Size code A null 0,14 B null 0,25 C (Ref.) D null 0,25 E (Ref.) H (Ref.) T null 0,06 Mass (Ref.) kg/1 000 pieces 16 10,16 6,40 10,57

23、 15,88 1,4 2,1 0,64 0,83 18 10,20 10,20 18,00 1,3 1,6 0,30 0,49 19 10,87 11,14 19,05 1,8 2,19 0,41 0,86 BS EN 6094:2016EN 6094:2016 (E) 6 3.2 Material and surface treatment See Table 2. Table 2 Material and surface treatment Size code Material Tensile strength MPa Surface treatment 16 Corrosion resi

24、stant steel 1.4310 per EN10088-2 1 100 1 300 Passivated per AMS 2700 or EN 2516 18 Steel FE-PM3902 (X7CrNiAl17-7) per EN2540 or equivalent 1 160 min. 19 Corrosion resistant steel 1.4310 per EN10088-2 1 100 1 300 3.3 Static values The washer shall be capable to withstand the loads given in Table 3 wi

25、thout permanent deformation. Load direction is outlined in Figure 2. NOTE Size code 19 must not be used in combination with quick release fastener system EN 6088, EN 6092, EN 6093 and EN 6105. Table 3 Static values Size code Minimum pre-load N 16 3 000 18 19 2 000 3.4 Operating temperature This wash

26、er shall be used in the temperature range of 55 C to 150 C. 4 Designation EXAMPLE NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. BS EN 6094:2016EN 6094:2016 (E) 7 5 Marking EN 2424, style G. 6 Technical specification EN 6095. 7 Example of inst

27、allation See Figure 2 and Table 4. Key 1 Pre-load 2 Washer EN 6094 (installed condition) 3 Stud EN 6088 or EN 6105 4 Panel Figure 2 Example of installation Table 4 Installation hole sizes Size code null Z 16 10,8 null 0,1 18 10,5 null 0,1 19 11,4 null 0,1 BS EN 6094:2016EN 6094:2016 (E) 8 Bibliograp

28、hy 1 EN 6089, Aerospace series Washer, retaining, for usage with stud EN 60883)2 EN 6090, Aerospace series Washer, retaining3)3 EN 6091, Aerospace series Circlip3)3)Published as ASD Prestandard at the date of publication of this standard. This page deliberately left blankBSI is the national body res

29、ponsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together b

30、usiness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organization

31、s of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or

32、 Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Devel

33、opment Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the

34、international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, o

35、r publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company us

36、e only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standa

37、rd purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network

38、, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. Fo

39、r further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touc

40、h with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy

41、 of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as y

42、ou wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to be

43、nefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20