EN 6059-501-2010 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 501 Voltage proof test《航空航天系列 电缆安装 保护套管 试验法 第501部分 电压保护测试》.pdf

《EN 6059-501-2010 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 501 Voltage proof test《航空航天系列 电缆安装 保护套管 试验法 第501部分 电压保护测试》.pdf》由会员分享，可在线阅读，更多相关《EN 6059-501-2010 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 501 Voltage proof test《航空航天系列 电缆安装 保护套管 试验法 第501部分 电压保护测试》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN6059-501:2010ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Electrical cables,installation Protection sleeves Test methodsPart 501: Voltage proof testThis British Standardwas published under theauthority of the StandardsPolicy an

2、d StrategyCommittee on 31 May2010. BSI 2010ISBN 978 0 580 62005 8Amendments/corrigenda issued since publicationDate CommentsBS EN 6059-501:2010National forewordThis British Standard is the UK implementation of EN 6059-501:2010.The UK participation in its preparation was entrusted to TechnicalCommitt

3、ee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.

4、Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 6059-501:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-501 April 2010 ICS 49.060 English Version Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 501: Vo

5、ltage proof test Srie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 501 : Tenue en tension Luft- und Raumfahrt - Elektrische Leitungen, Installation - Schutzschluche - Prfverfahren - Teil 501: Spannungsfestigkeit This European Standard was approved by

6、 CEN on 16 January 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand

7、ards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified t

8、o the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,

9、 Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of

10、exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-501:2010: EBS EN 6059-501:2010EN 6059-501:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Dielectric test .43.1 Equipment 43.2 Preparation of specimens .43.3 Test procedure .

11、43.4 Requirement .4Annex A (informative) Schematic drawing of the dielectric equipment 5BS EN 6059-501:2010EN 6059-501:2010 (E) 3 Foreword This document (EN 6059-501:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries an

12、d votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standa

13、rd, either by publication of an identical text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at the latest by October 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

14、CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cypru

15、s, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 6059-501:2010EN 6059-501:2010 (E

16、) 4 1 Scope This standard specifies a method of performing voltage proof tests on finished protection sleeves. It shall be used together with EN 6059-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

17、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General 3 Dielectric test 3.1 Equipment The dielectric equipment is

18、 composed of an electrical generator and a test fixture. The test fixture is composed of a structure containing several rows of metallic ball chains and a metallic mandrel. The negative pole of the electrical generator is connected to the metallic mandrel with a clip. The positive pole is connected

19、to the metallic ball chains and the metallic frame. See a type of equipment in Annex A (informative). 3.2 Preparation of specimens The specimen and the metallic mandrel are 50 cm long. The external diameter of the metallic mandrel shall be as closed as possible to the internal diameter of the protec

20、tion sleeve to test. The specimen is installed on the metallic mandrel which is connected to the negative pole of the generator. The assembly is installed into the chamber so that the ball chains are only in contact with the specimen and not with the mandrel. The not protected part of the metallic m

21、andrel which allows the connection must be kept out of the chamber. 3.3 Test procedure The protection sleeve shall be subject to a voltage test at ambient temperature. The voltage specified by the technical specification with a frequency of 40 Hz to 60 Hz, shall be applied for at least 1 min between

22、 the metallic ball chains and the mandrel. The voltage rise time shall be between 300 V/s and 500 V/s. After 1 min at the value defined in the product standard, the test should be stopped. 3.4 Requirement There shall be no electrical perforation of the sleeve and no evidence of damage. BS EN 6059-50

23、1:2010EN 6059-501:2010 (E) 5 Annex A (informative) Schematic drawing of the dielectric equipment Key 1 Specimen under test: 400 mm 2 Metallic mandrel 3 Metallic ball chains 4 Test fixture 5 Sleeve protection 6 Electrical generator 7 Value kilovolts (kV) Figure A.1 BS EN6059-501:2010BSI GroupHeadquar

24、ters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by

25、Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an ina

26、ccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which

27、ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a deb

28、it/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on

29、 national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 70

30、48 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information rega

31、rding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardiz

32、ation bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the

33、free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: