EN 6059-202-2016 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 202 Dimensions and mass《航空航天系列-安装保护轴套电缆试验方法-第202部分 尺寸和质量》.pdf

《EN 6059-202-2016 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 202 Dimensions and mass《航空航天系列-安装保护轴套电缆试验方法-第202部分 尺寸和质量》.pdf》由会员分享，可在线阅读，更多相关《EN 6059-202-2016 en Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 202 Dimensions and mass《航空航天系列-安装保护轴套电缆试验方法-第202部分 尺寸和质量》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 6059-202:2016Aerospace series Electricalcables, installation Protection sleeves TestmethodsPart 202: Dimensions and massBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 6059-202:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implemen

2、tation of EN 6059-202:2016.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to

3、 include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 95149 7 ICS 49.060 Compliance with a British Standard cannot confer immunity from legal obligations.Thi

4、s British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 6059-202:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-202 December 2016 ICS 49.060 E

5、nglish Version Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 202: Dimensions and mass Srie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 202: Dimensions et masse Luft- und Raumfahrt - Elektrische Leitung

6、en, Installation - Schutzschluche - Prfverfahren - Teil 202: Mae und Masse This European Standard was approved by CEN on 23 October 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nationa

7、l standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A versio

8、n in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Cze

9、ch Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. E

10、UROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6059-202:2016

11、 EBS EN 6059-202:2016EN 6059-202:2016 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Equipment . 4 4 Procedures 4 5 Requirements . 5 BS EN 6059-202:2016EN 6059-202:2016 (E) 3 European foreword This document (EN 6059-202:2016) has been prepared by the Aerospace and Defen

12、ce Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presen

13、tation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be withdrawn at the latest by June 2017. Attention is drawn to the possibility th

14、at some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound t

15、o implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R

16、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6059-202:2016EN 6059-202:2016 (E) 4 1 Scope This European Standard specifies a method for the examination of dimensions and mass of protection sleeve for electrical cable and cable bundles. It shall be used

17、together with EN 6059-100. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

18、cument (including any amendments) applies. EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General EN 6059-401, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 401: Expansion range 1)3 Equipment The followi

19、ng equipment shall be required for these tests: For the examination of the mass an instrument with an electronic scale shall be used with an accuracy of at least 0,05 g. For the examination of the delivered diameter a mandrel with the specified delivered diameter and a minimum length of 350 mm shall

20、 be used. For detailed dimensions e.g. diameter of fibres, thickness of sheet when applicable (e.g. metal foils) a micrometre with an accuracy of at least 0,05 mm shall be used. For textile fabrics (woven, knitted, braided, and non-woven mats) a disk micrometre of the non-rotating spindle type shall

21、 be used and the measure must be taken on the flat fabric. The disk shall have a diameter of 20 mm 1,0 mm. 4 Procedures 4.1 Dimensions Measurement of the delivered diameter: The length of the sleeve shall be measured before and after application of the sleeve to the mandrel. If the delivered diamete

22、r is the maximum diameter or the minimum diameter, the length of the sleeve shall be measured on the mandrel in the test conditions mentioned in EN 6059-401. If the delivered diameter is between the maximum diameter and the minimum diameter, the sleeve shall be slid over the mandrel. The sleeve shal

23、l contact the mandrel at all places by use of tape which is wrapped around the sleeve. Measurement other dimensions (if applicable): All other dimensions shall be measured in the delivered condition (not mounted on a mandrel). 1) Published as ASD-STAN Prestandard at the date of publication of this s

24、tandard by AeroSpace and Defence industries Association of Europe - Standardization (ASD-STAN) (www.asd-stan.org) BS EN 6059-202:2016EN 6059-202:2016 (E) 5 4.2 Mass The examination of the mass shall be conducted on a specimen at least 0,5 m long, expressed in g/m. 5 Requirements 5.1 Dimensions The m

25、aximum difference between the measured lengths of the specimen (before and after application on the mandrel) shall comply with the product standard. Other dimensions (if applicable) shall comply with the product standard. 5.2 Mass The mass of the specimen shall comply with the product standard. This

26、 page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are publish

27、ed by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assemb

28、led in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about

29、 British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can als

30、o be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted

31、 by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion o

32、f the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchase

33、d in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for perso

34、nal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need mor

35、e than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.Subscriptions

36、Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its

37、 available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service

38、 exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to hos

39、t standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by am

40、endment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orde

41、rs): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20