EN 546-3-2006 en Aluminium and aluminium alloys - Foil - Part 3 Tolerances on dimensions《铝和铝合金 箔 第3部分 尺寸公差》.pdf

《EN 546-3-2006 en Aluminium and aluminium alloys - Foil - Part 3 Tolerances on dimensions《铝和铝合金 箔 第3部分 尺寸公差》.pdf》由会员分享，可在线阅读，更多相关《EN 546-3-2006 en Aluminium and aluminium alloys - Foil - Part 3 Tolerances on dimensions《铝和铝合金 箔 第3部分 尺寸公差》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 546-3:2006Aluminium and aluminium alloys Foil Part 3: Tolerances on dimensionsThe European Standard EN 546-3:2006 has the status of a British StandardICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55

2、g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 546-3:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50134 0National forewordThis British Standard was pub

3、lished by BSI. It is the UK implementation of EN 546-3:2006. It supersedes BS EN 546-3:1997 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on NFE/35 can be obtained on request

4、to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPE

5、AN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 546-3December 2006ICS 77.150.10 Supersedes EN 546-3:1996 English VersionAluminium and aluminium alloys - Foil - Part 3: Tolerances ondimensionsAluminium et alliages daluminium - Feuille mince - Partie 3: Tolrances sur dimensionsAluminium und Aluminiumlegie

6、rungen - Folien - Teil 3:GrenzabmaeThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-

7、date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the

8、responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ire

9、land, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36

10、 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 546-3:2006: EEN 546-3:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Tolerances on dimensions for single-rolled foil.4 3.1 Gauge4 3.2 Widt

11、h .6 4 Tolerances on dimensions for double-rolled foil .6 4.1 Gauge6 4.2 Width .7 Bibliography 8 Tables Table 1 Tolerances on average evaluation of gauge for single rolled foil .5 Table 2 Density.6 Table 3 Tolerance on width for single-rolled foil 6 Table 4 Tolerances on mean measurement of gauge fo

12、r double-rolled foil 7 EN 546-3:2006 (E) 3 Foreword This document (EN 546-3:2006) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by public

13、ation of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. This document supersedes EN 546-3:1996. Within its program of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 6 “Foil and finstock“

14、 to revise EN 546-3:1996. The following modifications have been made: subclause 3.1.1: the following text “ at 90 % confidence limits“ has been deleted; subclause 3.1.2: title is changed; subclause 4.1.1: the following text “ at 90 % confidence limits“ has been deleted; subclause 4.1.2: title is cha

15、nged. EN 546 comprises the following parts under the general title “Aluminium and aluminium alloys- Foil“: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions Part 4: Special property requirements Attention is drawn to the possibili

16、ty that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under r

17、easonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,

18、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 546-3:2006 (E) 4 1 Scope This document sp

19、ecifies the tolerances on dimensions for single and double-rolled aluminium and aluminium alloy foil supplied in accordance with EN 546-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

20、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. Not Applicable 3 Tolerances on dimensions for single-rolled foil 3.1 Gauge 3.1.1 Single gauge measurement The tolerance on gauge for a single measurement for single-rolled foil shall be 6

21、 %. Gauge can be measured with any of the usual precision instruments capable of assessing foil thickness but, in the event of a dispute, the weighing method shall be used as a referee procedure. Description of the weighing method: for the test sample, cut an area A of approximately 1 dm2either squa

22、re or circular. Degrease the sample if necessary in a suitable solvent and weigh on a laboratory balance with an accuracy of equal to or better than 1 mg. The dimensions of the sample (sides of square or diameter of circle) shall be measured with an accuracy of equal to or better than 0,1 mm. Gauge

23、shall be calculated by use of the formula: DAME=10where: E is the gauge in micrometres; M is the mass in milligrams; D is the density as defined in Table 2, in grams per cubic centimetre; A is the area in square decimetres. EN 546-3:2006 (E) 5 3.1.2 Average gauge evaluation The tolerance on gauge fo

24、r an average evaluation is specified in Table 1. Table 1 Tolerances on average evaluation of gauge for single rolled foil Lot size Tolerance kg % 3 000 6 3 000 to 10 000 5 10 000 4 Mean gauge may be obtained by either : a) Calculation : calculation of average evaluation by this method requires an ac

25、curate knowledge of length and net mass of the reels. The average evaluation shall be calculated by the formula : DWLPE=6m10where: Emis the average evaluation in micrometers; P is the net mass in kilograms; L is the length in metres; W is the width in millimetres; D is the density as defined in Tabl

26、e 2, in grams per cubic centimetres. EN 546-3:2006 (E) 6 Table 2 Density Material Density g/cm3EN AW-1050A 2,70 EN AW-1200 2,71 EN AW-3003 2,73 EN AW-3005 2,73 EN AW-3103 2,73 EN AW-8006 2,74 EN AW-8008 2,74 EN AW-8011A 2,71 EN AW-8014 2,73 EN AW-8021B 2,72 EN AW-8079 2,71 EN AW-8111 2,71 b) averagi

27、ng spot measurements. The method shall be agreed between purchaser and supplier. 3.2 Width The tolerance on width for single-rolled foil is specified in Table 3. Table 3 Tolerance on width for single-rolled foil Dimensions in millimetres Width ToleranceSymmetrical Only plus Only minus 1 000 1 20+02-

28、 1 000 2 40+04- Unless otherwise specified in the order, the type of tolerance is at the discretion of the supplier. 4 Tolerances on dimensions for double-rolled foil 4.1 Gauge 4.1.1 Single gauge measurement The tolerance on gauge for a single measurement for double-rolled foil shall be 8 %. The met

29、hod of single gauge measurement shall be as given in 3.1.1. 4.1.2 Average gauge evaluation The tolerance on gauge for an average evaluation for double-rolled foil is specified in Table 4. EN 546-3:2006 (E) 7 Table 4 Tolerances on mean measurement of gauge for double-rolled foil Lot size Tolerance kg

30、 % 3 000 8 3 000 to 10 000 6 10 000 4 The method of average gauge evaluation shall be as specified in 3.1.2. 4.2 Width The tolerance on width for double-rolled foil shall be as specified in Table 3 for single-rolled foil. EN 546-3:2006 (E) 8 Bibliography 1 EN 546-1, Aluminium and aluminium alloys Fo

31、il Part 1: Technical conditions for inspection and delivery blankBS EN 546-3:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati

32、onal level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would

33、 be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an indivi

34、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. E

35、mail: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI pr

36、ovides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Te

37、l: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20

38、 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications

39、. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocop

40、ying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.