EN 3475-809-2009 en Aerospace series - Cables electrical aircraft use - Test methods - Part 809 Resistance unbalance《航空航天系列 飞机用电缆 测试方法 第809部分 抗非平衡性》.pdf

《EN 3475-809-2009 en Aerospace series - Cables electrical aircraft use - Test methods - Part 809 Resistance unbalance《航空航天系列 飞机用电缆 测试方法 第809部分 抗非平衡性》.pdf》由会员分享，可在线阅读，更多相关《EN 3475-809-2009 en Aerospace series - Cables electrical aircraft use - Test methods - Part 809 Resistance unbalance《航空航天系列 飞机用电缆 测试方法 第809部分 抗非平衡性》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN3475-809:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Cables, electrical,aircraft use TestmethodsPart 809: Resistance unbalanceThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommitt

2、ee on 30 April2009 BSI 2009ISBN 978 0 580 62411 7Amendments/corrigenda issued since publicationDate CommentsBS EN 3475-809:2009National forewordThis British Standard is the UK implementation of EN 3475-809:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerosp

3、ace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with

4、a British Standard cannot confer immunityfrom legal obligations.BS EN 3475-809:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3475-809March 2009ICS 49.060English VersionAerospace series - Cables, electrical, aircraft use - Testmethods - Part 809: Resistance unbalanceSrie arospatiale - Cbles l

5、ectriques usagearonautique - Mthodes dessais - Partie 809:Dsquilibre de rsistanceLuft- und Raumfahrt - Elektrische Leitungen frLuftfahrtverwendung - Prfverfahren - Teil 809:WiderstandsunsymmetrieThis European Standard was approved by CEN on 11 July 2008.CEN members are bound to comply with the CEN/C

6、ENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to an

7、y CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN

8、 members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Swede

9、n, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No

10、. EN 3475-809:2009: EBS EN 3475-809:2009EN 3475-809:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Preparation of specimens .4 4 Apparatus .4 5 Method 4 6 Requirement .4 BS EN 3475-809:2009EN 3475-809:2009 (E) 3 Foreword This document (EN 3475-809:2009) has been prepared by

11、 the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of

12、ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by September 2009. Attent

13、ion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of t

14、he following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak

15、ia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3475-809:2009EN 3475-809:2009 (E) 4 1 Scope This standard specifies methods for measuring resistance unbalance for digital data transmission cable. It shall be used together with EN 3475-100. 2 Normative references The following

16、referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3475-100, Aerospace series Cables, electrical, aircraft use

17、Test methods Part 100: General. EN 3475-301, Aerospace series Cables, electrical, aircraft use Test methods Part 301: Ohmic resistance per unit length. 3 Preparation of specimens The measurements may be performed on production drums and/or on the final delivery package. 4 Apparatus Wheatstone bridge

18、s, automatic or semi-automatic equipment may also be used with an accuracy of 0,5 %. 5 Method The conductor resistance unbalance is usually determined at the same time that conductor resistance measurements are made (EN 3475-301). The resistance measure of each conductor of any pair shall be perform

19、ed at or corrected to 20 C temperature. The temperature correction shall be performed as described in test method EN 3475-301. After measurement, the resistance unbalance calculation is: 100baba1=+RRRRDR 100dcdc2=+RRRRDR where ba,RR are the resistance of each conductor of the pair 1; and dc,RR are t

20、he resistance of each conductor of the pair 2 (in case of quad cable). Used expression for DR1and DR2are percent resistance unbalance. 6 Requirement The resistance unbalance obtained shall not exceed the values specified in the product standard. BS EN 3475-809:2009This page has been intentionally le

21、ft blank BS EN3475-809:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at th

22、einternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.W

23、e would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an in

24、dividual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 E

25、mail: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standard

26、sBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Te

27、l:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax:

28、 +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the

29、publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenper

30、mission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: