EN 3475-806-2002 en Aerospace Series - Cables Electrical Aircraft Use - Test Methods - Part 806 Attenuation《航空航天系列 飞机用电缆 测试方法 第806部分 衰减》.pdf

《EN 3475-806-2002 en Aerospace Series - Cables Electrical Aircraft Use - Test Methods - Part 806 Attenuation《航空航天系列 飞机用电缆 测试方法 第806部分 衰减》.pdf》由会员分享，可在线阅读，更多相关《EN 3475-806-2002 en Aerospace Series - Cables Electrical Aircraft Use - Test Methods - Part 806 Attenuation《航空航天系列 飞机用电缆 测试方法 第806部分 衰减》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Cables, electrical, aircraft use Test methods Part 806: Attenuation The European Standard EN 3475-8062002 has the status of a British Standard ICs 49.060 BS EN 3475-80612002 BS EN 3475-806:2002 National foreword This British Standard is the official English language version of The UKparticipation in

2、 its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee, ACE/6/2, Aerospace - Cables, which has the responsibility to: EN 3475-80612002. This British Standard, having been prepared under the direction of the Engineering Se

3、ctor Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 25 June 2002 - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK i

4、nterests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cros s-r e ferenc es The British Standards which implement international or European publi

5、cations referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary prov

6、isions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5

7、and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd.No. I Date I Comments O BSI 25 June 2002 ISBN O 580 39908 7 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3475-806 June 2002 ICs 49.060 Engl

8、ish version Aerospace series - Cables, electrical, aircraft use - Test methods - Part 806: Attenuation Srie arospatiale - Cbles lectriques usage aronautique - Mthodes dessais - Partie 806: Affaiblissement Luft- und Raumfahrt - Elektrischen Leitungen fr Luftfahrt Verwendung - Prfverfahren - Teil 806:

9、 Dmpfung This European Standard was approved by CEN on 20 January 2002 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographi

10、cal references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN me

11、mber into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway

12、, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and by any means reserved worldwide

13、 for CEN national Members. Ref. No. EN 3475-806:2002 E EN 3475-80612002 (E) Foreword This document (EN 3475-806:2002) has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this Standar

14、d has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

15、by December 2002, and conflicting national standards shall be withdrawn at the latest by December 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, D

16、enmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 3475-80612002 (E) - / a/ b F 1 Scope Indicator This standard specifies methods for measuring the attenuation of a cable. It sha

17、ll be used together with EN 3475-100. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated reference

18、s, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3475-100 Aerospace series - Cables, electrical, aircraft u

19、se - Test methods - Part 100: General 3 Preparation of specimens Connectors shall be fitted on each end of the test specimens (coaxial cables) or the test specimens shall be stripped (balanced cables) and connected to the measuring device. 4 Methods 4.1 Insertion method Measurement of attenuation is

20、 carried out by transmission in harmonic mode at the frequencies indicated in the product standard, inserting a cable sample in a suitable circuit and by compensating the attenuation caused by this cable by means of a calibrated attenuator. The sample shall be of a length i such that it produces, un

21、less otherwise stipulated in the product standard, an attenuation equivalent to at least 3 dB. Figure 1 shows a basic arrangement. The generator is adjusted to the measuring frequency F and its output level is held constant throughout measurement. The indicator consists either of a measurement recei

22、ver or a detector followed by a d.c. or low frequency voltmeter if the generator is modulated. I Fixled Adaptor attenuator Figure 1 3 EN 3475-80612002 (E) The adaptor devices shown in figure 1 are intended to ensure correct connection between the measuring line and the cable to be tested. Since the

23、measuring line is a coaxial cable, these devices shall not be used if the cable to be tested has a coaxial structure of the same rated characteristic impedance as the line: these are impedance transformers in the case of coaxial cables with different rated characteristic impedance: these are balance

24、d transformers in the case of symmetrical cables (pairs). First note the output level on the indicator which corresponds to a value NI on the calibrated variable attenuator. Then connect the test sample between a and b and readjust the variable attenuator so as to obtain the same indicator level as

25、in the previous operation; if N2 is the new value shown on the variable attenuator, attenuation is: in decibels per metre at 20 “C NI -N2 a= L1+ 0,002 (t - 20) where tis the temperature, in degrees Celsius, of the test specimens. 4.2 The attenuation constant shall be determined from the ratio of the

26、 input and output voltage or power. Both quantities may be measured in turn by a single measuring receiver or simultaneously with a network analyser or two channel powermeters. In the case of a balanced cable, the measurement shall be carried out in a balanced condition. If the measuring test equipm

27、ent is an unbalanced one, both ends of the pair shall be connected to the test equipment by means of baluns. The baluns shall be selected to match the test equipment to the cable nominal impedance at the test frequency. Comparison of input and output voltage or power (insertion loss 2 3 db) Layout T

28、he test equipment shall be assembled generally in accordance with one of the two circuit arrangements shown in figure 2 or figure 3. a b I I X+ 8 9 Figure 2 - Layout of test circuit for comparison -Test set up A Where: 1 : generator 2 : attenuator 6 dB 5 : testspecimen 6 : insertion unit 8 : termina

29、ting load 9 : network analyser 10 : matching baluns (measurement on a balanced cable with an unbalanced measuring test equipment) 4 EN 3475-80612002 (E) a b I 5 6 8 Figure 3 - Layout of test circuit for comparison -Test set up B Where: 1 : generator 2 : attenuator 6 dB 5 : testspecimen 6 : insertion

30、 unit 7 : measuring receiver 8 : terminating load 9 : network analyser 10 : matching baluns (measurement on a balanced cable with an unbalanced measuring test equipment) Procedure For test set up A, the test circuit shall be calibrated at the test frequency with the test ports connected together. Th

31、e test specimen shall then be inserted into the circuit and the ratio of the input and output voltage or power shall be recorded, reading a in decibels. Expression of results The attenuation constant shall be determined as follows: a Testset upA a = , in decibels per metre at 20 “C L I + 0,002 (f -

32、20) , in decibels per metre at 20 “C al - a2 Testset upB a = L I + 0,002 (f-20) Where: a is the test circuit A reading in decibels al is the circuit B reading without the test specimen in decibels a2 is the circuit B reading with the test specimen in decibels L is the length of the test specimen in

33、metres t is the temperature of the test specimen in degrees Celsius 5 The values obtained shall not exceed the values specified in the product standard. Req u i remen t 5 BS EN 3475-80612002 B SI 389 Chiswick High Road London w4 4AL BSI -British Standards Institution BSI is the independent national

34、body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the la

35、test amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which

36、 can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and for

37、eign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI impl

38、ementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic i

39、nformation services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discount

40、s on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.

41、bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and P

42、atents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course ofimplementing the standard, ofneces

43、sary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.