EN 3339-2006 en Aerospace series - Aluminium alloy AL-P7010- - T76 - Die forgings - a less than or equal to 200 mm《航天航空系列 AL-P7010-T76型铝合金 模锻件 a≤200mm》.pdf

《EN 3339-2006 en Aerospace series - Aluminium alloy AL-P7010- - T76 - Die forgings - a less than or equal to 200 mm《航天航空系列 AL-P7010-T76型铝合金 模锻件 a≤200mm》.pdf》由会员分享，可在线阅读，更多相关《EN 3339-2006 en Aerospace series - Aluminium alloy AL-P7010- - T76 - Die forgings - a less than or equal to 200 mm《航天航空系列 AL-P7010-T76型铝合金 模锻件 a≤200mm》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3339:2006Aerospace series Aluminium alloy AL-P7010- T76 Die forgings a u 200 mmThe European Standard EN 3339:2006 has the status of a British StandardICS 49.025.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55

2、g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3339:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978-0-580-49943-2National forewordThis British Standard was publi

3、shed by BSI. It is the UK implementation of EN 3339:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Subcommittee ACE/61/-/24, Light alloys.A list of organizations represented on ACE/61/-/24 can be obtained on req

4、uest to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsE

5、UROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3339 December 2006 ICS 49.025.20 English Version Aerospace series - Aluminium alloy AL-P7010- - T76 - Die forgings - a 200 mm Srie arospatiale - Alliage daluminium AL-P7010- - T76 - Pices matrices - a 200 mm Luft- und Raumfahrt - Aluminiumlegierung

6、 AL-P7010- - T76 - Gesenkschmiedestcke - a 200 mm This European Standard was approved by CEN on 5 October 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alt

7、eration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tran

8、slation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,

9、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management C

10、entre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3339:2006: E2 Foreword This document (EN 3339:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - S

11、tandardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard s

12、hall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. Attention is drawn to the possibility that some of the elements of this documen

13、t may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Aus

14、tria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3339:20063 Intr

15、oduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-2. 1 Scope This standard specifies the requirements relating to: Alum

16、inium alloy AL-P7010- T76 Die forgings a 200 mm for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refere

17、nced document (including any amendments) applies. EN 2082-3, Aerospace series Aluminium alloy forging stock and forgings Technical specification Part 3: Pre-production and production forgings. EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of

18、 EN standards and their use. EN 4287, Aerospace series Aluminium alloy AL-P7010 Forging stock. EN 4500-2, Aerospace series Metallic materials Rules for drafting and presentation of material standards Part 2: Specific rules for aluminium, aluminium alloys and magnesium alloys. 1)EN 4527, Aerospace se

19、ries Aluminium and aluminium alloy products Test methods Determining susceptibility to stress-corrosion cracking. 1)1) Published as ASD Prestandard at the date of publication of this standard. EN 3339:20064 1 Material designation Aluminium alloy AL-P7010- Others Element Si Fe Cu Mn Mg Cr Ni Zn Zr Ti

20、 Each Total Al min. 1,5 2,1 5,7 0,10 2 Chemical composition % max. 0,12 0,15 2,0 0,10 2,6 0,05 0,05 6,7 0,16 0,06 0,05 0,15 Base 3 Method of melting 4.1 Form Die forgings 4.2 Method of production Forged from forging stock EN 4287 4.3 Limit dimension(s) mm a 200 5 Technical specification EN 2082-3 De

21、livery condition T76 6.1 Heat treatment 470 C 480 C / WQ 80 C a + 110 C 120 C / 8 h t 24 h b + 170 C 180 C / 6 h t 16 h b6.2 Delivery condition code U Use condition T76 7 Heat treatment Delivery condition Characteristics 8.1 Test sample(s) See EN 2082-3. 8.2 Test piece(s) See EN 2082-3. 8.3 Heat tre

22、atment Use condition 9 Dimensions concerned mm 80 80 a 100 100 a 120 120 a 160 160 a 200 10 Thickness of cladding on each face % 11 Direction of test piece L LT ST L LT ST L LT ST L LT ST L LT ST 12 Temperature C Ambient Ambient Ambient Ambient Ambient 13 Proof stress Rp0,2MPa 470 460 450 440 435 43

23、5 435 430 430 430 425 425 415 400 39014 Strength RmMPa 530 520 510 500 495 490 495 490 485 490 485 480 470 460 45015 Elongation A % 8 6 3,5 8 6 3,5 8 6 3,5 6 5 3,5 5 4 3 16 T Reduction of area Z % 17 Hardness 18 Shear strength RcMPa 19 Bending k 20 Impact strength 21 Temperature C 22 Time h 23 Stres

24、s aMPa 24 Elongation a % 25 Rupture stress RMPa 26 C Elongation at rupture A % 27 Notes (see line 98) a, bEN 3339:20065 32 Electrical conductivity See EN 2082-3. 3Measurement on the surface of the sample from which tensile specimens are taken. 7 22,0 MS/m Acceptable 21,0 MS/m 22,0 MS/m Acceptable if

25、 Rp0,2 L Rp0,2 L min. c+ 70 MPa or if stress corrosion test is acceptable 21,0 MS/m Not acceptable 39 Stress corrosion 1 EN 4527 2 The “capability clause“ applies or as per line 32 3 a 25 mm 4 ST 6 = 175 MPa 7 t 20 d 40 See EN 2082-3.Fracture toughness (K1C) 7 Dimensions (mm) L-T MPa m T-L MPa m S-L

26、 MPa m a 100 25 24 22 100 a 150 25 22 21 150 a 200 25 21 20 44 External defects See EN 2082-3.51 Macrostructure EN 2082-3.61 Internal defects See EN 2082-3.82 Batch uniformity EN 2082-3.7 Electrical conductivity See EN 2082-3. or 155 (Typical value) Hardness HB 20 per product 30 per batch 95 Marking

27、 inspection See EN 2082-3. 96 Dimensional inspection See EN 2082-3. 98 Notes aThe use of quench additives or higher quenchant temperature shall be subject to agreement between manufacturer and purchaser. bArtificial ageing may be carried out using the following alternative single stage method: heati

28、ng to a temperature of 170 C 180 C at a rate not exceeding 20 C / h and soaking at this temperature for 6 h t 16 h. cIf L specimen cannot be cut, LT specimen shall be used by agreement between manufacturer and purchaser. 99 Typical use EN 3339:20066 100 Product qualification Qualification programme

29、to be agreed between manufacturer and purchaser. EN 3339:2006blankBS EN 3339:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati

30、onal level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would

31、 be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an indivi

32、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. E

33、mail: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI pr

34、ovides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Te

35、l: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20

36、 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications

37、. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocop

38、ying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.