EN 1941-1996 en Self Adhesive Tapes - Measurement of Elongation at Break《自胶粘带 断裂时伸长度的测量》.pdf

《EN 1941-1996 en Self Adhesive Tapes - Measurement of Elongation at Break《自胶粘带 断裂时伸长度的测量》.pdf》由会员分享，可在线阅读，更多相关《EN 1941-1996 en Self Adhesive Tapes - Measurement of Elongation at Break《自胶粘带 断裂时伸长度的测量》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 BSI BS*EN*L941 96 W 1624669 0567732 282 D BRITISH STANDARD Self adhesive tapes - Measurement of elongation at break * m * The European Standard EN 1941 : 1996 has the status of a British Standard ICs 83.180 BS EN 1941 : 1996 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW i ,

2、 I r - BSI BS*EN*1941 96 m 1624669 0567733 119 Amd. No. Date BS EN 1941 : 1996 Text affected Committees responsible for this British Standard The preparation of this British Standxd was entrusted to Technical Committee PKWB, Distribution packaging, tramport, packaging and unit loads, upon which the

3、following bodies were represented This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Board, was published under the authority of the Sandards Board and comes into effect on 15 October 1996 O BSI 1996 British Adhesives and Sealants Association

4、 British Apparel and Textile Confederation British Carton Association British Coatings Federation Ltd. British Fibreboard Packaging Association British Glass Manufacturers Confederation British industnal Truck Association British Plastics Federation British Retail Consortium British Rubber Manufactu

5、rers Association Ltd. British Tensional Srapping Association Ltd. British Timber Merchants Association British Wood Preserving and Damp-proofing Chamber of Shipping Chemical Industries Association China Clay Association Cranfield Logistics Department of Transport Engineering Equipment and Materials

6、Users Federation of the Electronics Industry Flexible IBC Association Food and Drink Federation independent Pallet Repair Committee institute of Grocery Distribution Metal Packaging Manufacturers Association Ministry of Defence National Association of Pallet Distributors Power Fastenings Association

7、 pira International Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Storage Equipment Manufacturers Association Timber Packaging and Pallet Confederation amber Research and Development United Kingdom Softwood Sawmillers Association Association Ltd. Association Associa ti on

8、The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Adhesive Tape Manufacturers Association British Footwear Manufacturers Federation British Steel industry (Wire Section) Packaging Distributors Association Pressure Sensitive Manufacturers As

9、sociation The following BSI references relate to the work on this standard: Committee reference PKW/3 Draft for comment 92/4244 DC ISBN O 680 26228 6 BSI BS*EN*L4L b 1624bb 05b7734 055 BS EN 1941 : 1996 Contents page Committees responsible Inside front cover National foreword ii Foreword 2 Text of E

10、N 1941 3 * * u O BSI 1996 i BSI BS*EN*l4L b m Lb24bb9 0567735 T91 m BS EN 1941 : 1996 National foreword This British Standard has been prepared by Technical Committee PKWB and is the English language version of EN 1941 : 1996 Self adhes.ive tupe-s - Mmurement of elongation at break published by the

11、European Committee for Standardization ICEN). Compliance with a British Standard does not of itself confer immunity from legal obligations. ii O BSI 1996 BSI BS*EN*iL941 b Lb24bb9 05b773b 928 m EuRopEAN STANDARD EN 1941 NORME EuR0PEE;”E EUROP- NOFW February 199 ICs 83.180 Descriptors: Adhesive tapes

12、, tension tapes, elongation at break English version Self adhesive tapes - Measurement of elongation at break Rubans autuadha - Mesure de lallongement ia rupture Klebebnder - Messung der Reidehnung This European Standard was approved by CEN on 1!29641-14. CEN members are bound to comply with the CEN

13、/CENELEC Internal Regdations which stipulate the conditions for giving this European Standard the status of a national stanard without any alteration. Upto-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any

14、 CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officiai versions. CE

15、N members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Gemx Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. European Committee for Standardhtion Comit Europen de Normalisation Europisches K

16、omitee fur Normung Central Secretariat: rue de Stassart 36, B-1060 Brussels O 1996 All rights of reproduction and communication in any form and by any means reserved in all counh-ies to CEN and its members. Ref, No. EN 1941 : 1996 E Foreword This European Standard has been prepared by khnical Commit

17、tee CENK 253, Self adhesive tapes, of which the secretariat is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 1996, and confiicting national standards shall be withdrawn at

18、the latest by August 1996, According to the CEN/CENELEC Internai Regulations, the following countries are bound to implement this European Smdard Austria, Belgium, Denmark, Finkuid, France, Germany, Greece, Iceland, Irehd, Italy, Luxembourg, Netherlands, Norway, Portugai, Spain, Sweden, Switzerland

19、and the United Kingdom. Contents Foreword 1 Scope 2 Denition 3 principle 4 4P- 6 6 Procedure 7 Expression of results 8 Test report Test sample and test pieces page 2 3 3 3 3 3 3 3 3 O BSI 1996 1 scope This standard specifies a method to measure the elongation of a self adhesive tape when it is subje

20、cted to a tensile force sufcient to cause it to break. The elongation at break of the adhesive tape is of value as an indication of its uniformity and quality, as well as a rough indication of its ability to conform to curved and irregular surfaces. It is usually determined at the same time as the b

21、reakang strength. The maximum width of adhesive tape tested by this method is 25 m. For adhesive tapes of this width or less, the elongation at break measured corresponds to that as supplied commerciaiiy, with factory-cut edges. For adhesive tapes wider than 25 mm, this test method provides for the

22、tape to be cut down to 25 mm with a wellsharpened instrument. In such cases, because of the better cutting of the edges, the results can be higher than would be found on commercial adhesive tape. 2 Denition For the purposes of this standard, the following definition applies: elongation at break The

23、increase in length of the adhesive tape at the time of breaking as a percentage of the 0righ-d length. 3 Principle The method consists of holding the adhesive tape vertically by the two clamps of a tensile testing machine. The elongation test is carried out una the adhesive tape breaks. 4 Apparatus

24、Tm testing machine, with the following characteristcs: - the force shall be indicated with a maximum error - the speed of the moveable clamp shall be 300 mm/min f 30 mm/h, - the scale shall be such that the re- obtained are between 15 % and 85 % of the complete scale; - the clamps shall be serrated

25、to prevent slipping or tearing of the adhesive tape; - if a pendulum machine is used, ensure that the pendulum can swing freely. of 2 04 5 Wst sample and test pieces Condition the sample roll for 24 hours at 23 “C f 2 “C and 50 % f 5 % relative humidity Discard the 3 outer turns of adhesive tape fro

26、m the roll. We from each roll 5 test pieces. Each test piece shall be 200 mm long and the same width as the adhesive tape. For widths greater than 25 mm, a test piece 25 mm wide shall be cut longitudinally from the adhesive tape. Use a sharp knife to obtain clean-cut edges. 6 Procedure 6.1 The test

27、shall be carried out at the standard conditions of 23 “C * 2 “C and 50 % f 5 % relative humidity 6.2 Remove the test pieces radially from the roil at an approxjmate speed of 300 mms, then condition for a further 2 h in the standard test conditions in order to remove all srain and distortion due to u

28、nwinding. 6.3 Set the clamps 100 mm apart. Clamp the test piece finnly so that the longitudinal axis is vertical and in lhe with the direction of the applied force. Check that the clamps move in the .same plane and parallel to the applied force and that the speed of separation is 300 mm/min 30 mmmin

29、. Reject ali test pieces which break within 5 mm of the clamps and carry out sufficient further tests to obtain 5 test pieces which break in the correct manner. Measure the distance between the clamps at break. 7 Expression of results Record the results as the percentage increase in the length of ad

30、hesive tape between the clamps when the adhesive tape breaks. Express the results as a percentage to the nearest whole number. Arrange the five readings in ascending numerical order. We the central value (median) as the elongation at break of the adhesive tape under test Because the resuits obtained

31、 with different tensie testing machines (pendulum or electronic) may not be directly comparable, the type of machine used shall be included in the test report. 8 !kst report The test report shail include the following information: a) a reference to this European Standard; b) ai information necessary

32、 to identify the test sample; c) the type of tensile testing machine used; d) the date of the test; e) the result obtained; f) any operation not specified in this European Standard which can influence the results. O BSI 1996 BSI BS*EN*L4L 96 Lb24bb9 05b7739 637 = BS EN 1941 : 1996 BSI 389 Chiswick H

33、igh Road London w4 4AL BSI - British Standards Institution 3SI is the independent national body responsible for preparing British Standards. It n-esents the UK view on standards in Europe and at the international level. It is ncorporated by Royal Charter. ?ontract requirements i British Standard doe

34、s not purport to include all the necessary provisions of a :ontract. Users of British Standards are responsible for their correct application. Eevisions 3ritisl-1 Standards are updated by amendment or revision. Users of British Standards ;houid make sure that they possess the latest amendments or ed

35、itions. t is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this 3ritish Standard would inform the Secretary of the responsible technical committee, he identity of which can be found on the in

36、side front cover. Tel 0181 996 9000; Fax: 1181 996 7400. 3SI offers members an individual updating service ded PLUS which ensures that rubscribers automatically receive the latest editions of standards. Buying standards 3rders for ail BSI, international and foreign standards publications should be t

37、ddressed to Customer Services, Sales Department at Chiswick Tel: 0181 996 7000; Fax: 0181 996 7001. in response to orders for international standards, it is BSI policy to supply the BSI unplementatjon of those that have been published as British Standards, unless Dthenvise requested. nformation on s

38、tandards BSI provides a wide range of information on national, European and intedonal standards through its Library, the Standardline Database, the BSI hformation Technology Service (SITS) and its Technical Help to Exporters Service. Contact the information Department at Chiswick Tel: 0181 996 7111;

39、 Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standasds. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001. Copyr

40、ight Copyright subsists in ali BSI publications. BSI also holds the copyright, in the UK, of the publications of the intrnational standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in

41、 any form or by any means - electronic, photocopying, recordmg or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are t

42、o be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL ISBN O 680 26228 6 PKWB