EN 1729-1-2015 en Furniture - Chairs and tables for educational institutions - Part 1 Functional dimensions (Incorporating corrigendum August 2016)《家具 教育单位的桌椅 第1部分 功能维度》.pdf

《EN 1729-1-2015 en Furniture - Chairs and tables for educational institutions - Part 1 Functional dimensions (Incorporating corrigendum August 2016)《家具 教育单位的桌椅 第1部分 功能维度》.pdf》由会员分享，可在线阅读，更多相关《EN 1729-1-2015 en Furniture - Chairs and tables for educational institutions - Part 1 Functional dimensions (Incorporating corrigendum August 2016)《家具 教育单位的桌椅 第1部分 功能维度》.pdf（74页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 1729-1:2015Furniture Chairs and tablesfor educational institutionsPart 1: Functional dimensionsBS EN 1729-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1729-1:2015.It supersedes BS EN 1729-1:2006 which is withdrawn.The UK

2、participation in its preparation was entrusted to TechnicalCommittee FW/0/4, Educational Furniture.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are respon

3、sible for its correctapplication. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 78949 6ICS 97.140Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Poli

4、cy and Strategy Committee on 31 December 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 1729-1:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1729-1 December 2015 ICS 97.140 Supersedes EN 1729-1:2006English Version Furniture - Chairs and tables for edu

5、cational institutions - Part 1: Functional dimensions Ameublement - Siges et tables pour tablissements denseignement - Partie 1 : Dimensions fonctionnellesMbel - Sthle und Tische fr Bildungseinrichtungen - Teil 1: Funktionsmae This European Standard was approved by CEN on 3 October 2015. CEN members

6、 are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

7、to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

8、 Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lit

9、huania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B

10、-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1729-1:2015 EBS EN 1729-1:2015EN 1729-1:2015 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .

11、5 4 Functional dimensions for chairs and tables 9 5 Marking 10 6 Instructions 10 7 Approval of range . 11 Annex A (normative) Functional dimensions for chairs with slopes between 5 and +7 and associated tables 12 A.1 Functional dimensions and size marks for chairs 12 A.2 Functional dimensions and si

12、ze marks for tables 19 A.3 Legroom . 20 A.4 Requirements for adjustable chairs and tables 20 Annex B (normative) Functional dimensions for high chairs with double-sloped seats and associated tables 22 B.1 Functional dimensions and size marks for chairs 22 B.2 Functional dimensions and size marks for

13、 tables 28 B.3 Legroom . 29 B.4 Requirements for adjustable high chairs with double-sloped seats and tables . 30 Annex C (normative) Functional dimensions for standing-height tables . 31 Annex D (normative) Functional dimensions for tall chairs with slopes between 5 and +7 and associated tables 33 D

14、.1 Functional dimensions and size marks for chairs 33 D.2 Functional dimensions and size marks for tables 39 D.3 Legroom . 41 D.4 Requirements for adjustable tall chairs 42 Annex E (normative) Functional dimensions for stools and associated worksurfaces . 43 E.1 Functional dimensions for stools . 43

15、 E.2 Functional dimensions for corresponding worksurface height 45 Annex F (normative) Determination of Point S, buttock zone, seat height, seat angles, seat depth and armrest height 47 F.1 The school chair measuring device (SCMD) . 47 F.2 Using the SCMD . 49 Annex G (informative) Guidance for the c

16、alculation of the height of adjustable chairs and tables in Annex A, Annex B and Annex D . 56 Annex H (informative) Guidance for the calculation of the height of chairs and tables in Annex B 57 Annex I (informative) Rationale 59 Bibliography . 70 BS EN 1729-1:2015EN 1729-1:2015 (E) 3 European forewo

17、rd This document (EN 1729-1:2015) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 201

18、6 and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Th

19、is document supersedes EN 1729-1:2006. Compared to EN 1729-1:2006, the following modifications have been made: a) addition of an annex for functional dimensions of tall chairs (Annex D); b) addition of an annex for functional dimensions of stools and associated worksurfaces (Annex E); c) key dimensi

20、ons of chairs in Annexes A and D are measured using the school chair measuring device (see Annex F), some of them when the chair is loaded with specified loads; d) a rationale for the functional dimensions of chairs and tables is provided (Annex I). EN 1729 is composed of the following parts: Part 1

21、: Functional dimensions the present document; Part 2: Safety requirements and test methods. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, C

22、zech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United King

23、dom. BS EN 1729-1:2015EN 1729-1:2015 (E) 4 Introduction This part of EN 1729 is based on the principle that chairs and tables, intended for use in educational institutions for general-purpose education, should be designed to encourage good postures. This part of EN 1729 takes selected national stand

24、ards into consideration. It does not specify design, but only those dimensions which promote good posture for either fixed or adjustable furniture. The dimensional requirements of this European Standard permit various interpretations of design; hence customs, educational practices, technical and fin

25、ancial circumstances of individual countries can be satisfied. It includes a rationale for the determination of functional dimensions. The minimum dimensions specified are considered as the absolute minimum. They can be exceeded. The maximum dimensions specified are considered as the absolute maximu

26、m; smaller dimensions can be used. EN 1729-2 specifies safety requirements and test methods. BS EN 1729-1:2015EN 1729-1:2015 (E) 5 1 Scope This European Standard specifies functional dimensions and markings for all chairs, stools and tables, for educational institutions, including fixed and adjustab

27、le chairs and tables. It applies to both un-upholstered and upholstered chairs and stools as well as to both non-swivel and swivel chairs. It applies to furniture for use with laptop computers or portable devices. It does not apply to ranked seating or special purpose workstations. It does not apply

28、 to furniture used by teaching personnel. Annex A (normative) includes single-sloped chairs and associated tables. Annex B (normative) includes double-sloped high chairs and associated tables. Annex C (normative) includes standing-height tables. Annex D (normative) includes tall chairs and associate

29、d tables. Annex E (normative) includes stools and associated worksurfaces. Annex F (normative) includes measurement methods. Annex G (informative) includes guidance on size marks for adjustable chairs and tables. Annex H (informative) includes guidance on calculating heights of double-sloped chairs

30、and associated tables. Annex I (informative) includes a rationale for functional dimensions. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applie

31、s. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1729-2, Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods 3 Terms and definitions For the purposes of this document, the following t

32、erms and definitions apply. 3.1 median plane vertical plane running from front to rear through the centre of the seat, dividing the chair into two equal parts Note 1 to entry: See Figure 1. 3.2 transverse plane vertical plane perpendicular to the median plane passing through the centre of the seat N

33、ote 1 to entry: See Figure 1. BS EN 1729-1:2015EN 1729-1:2015 (E) 6 Key 1 median plane 2 transverse plane Figure 1 Illustration of the median and transverse planes 3.3 most forward point of the backrest (Point S) most forward point in the specified range of the backrest on the median plane Note 1 to

34、 entry: The specified range of the backrest is shown in Table F.2. Note 2 to entry: See Figure A.3, Figure B.3 and Figure D.3. 3.4 adjustable furniture furniture that can be adjusted by the users (pupils), without the need for tools 3.5 multi-size furniture furniture that is adjustable at installati

35、on (not by the users) to change dimensions from one size mark to another 3.6 double-sloped seat seat intended for sitting using either the front part of the seat (leaning forward) or the rear part of the seat (leaning backward), with the feet resting on a footrest or the floor Note 1 to entry: See F

36、igure 5 and Figure B.5. 3.7 inclination of a single-sloped seat and of the front part of a double-sloped seat () angle formed by the front part of the seat and the horizontal Note 1 to entry: See Figure 2, Figure 3, Figure 4 and Figure 5. BS EN 1729-1:2015EN 1729-1:2015 (E) 7 Key 1 front 2 0 (positi

37、ve for forward-sloping seats) Figure 3 Example of a single-sloped seat with a positive seat angle Key 1 front 2 0 3 0 3 0 Figure 5 Example of a double-sloped seat (see Annex B) 3.8 inclination of the rear part of a double-sloped seat () angle formed by the horizontal and the rear part of the seat, d

38、etermined in the median plane Note 1 to entry: See Figure 5. 3.9 stool seating without backrest or armrests and intended for use for short periods Note 1 to entry: See Figure 6. The seat height to the footrest, h8, can be to one size mark and the seat height to the floor, h8, can be to another size

39、mark, as defined in Table E.1. Note 2 to entry: Any upward extension at the back of the stool below the Point S range specified in Table F.2 cannot be considered to be a backrest and the seating can be considered to be a stool (see Figure E.3). Key 1 footrest h8 seat height for stools as specified i

40、n Table E.1 h10 total stool height Figure 6 Stools with and without footrest BS EN 1729-1:2015EN 1729-1:2015 (E) 9 3.10 tall chair chair with the height of seat from the floor higher than the seat height specified in Table A.1 and with a footrest as shown in the figure below Note 1 to entry: See Fig

41、ure 7. Key 1 Point S 2 footrest h8 seat height for tall chair as specified in Table D.1 Figure 7 Tall chair with footrest 3.11 school chair measuring device SCMD measuring device intended for determining Point S, buttock zone and chair dimensions of school chairs Note1 to entry: Details of the SCMD

42、and the method of use are given in Annex F. 4 Functional dimensions for chairs and tables The functional dimensions and corresponding size marks and colour codes for chairs with slopes between 5 and +7 and associated tables shall be as specified in the normative Annex A. The functional dimensions an

43、d corresponding size marks and colour codes for high chairs with double-sloped seats and associated tables shall be as specified in the normative Annex B. The functional dimensions and corresponding size marks and colour codes for standing-height tables shall be as specified in normative Annex C. Th

44、e functional dimensions and corresponding size marks and colour codes for tall chairs shall be as specified in the normative Annex D. Tables suitable for tall chairs cannot be size marked. Tables shall correspond to the height of tall chairs as in Table D.2. BS EN 1729-1:2015EN 1729-1:2015 (E) 10 Th

45、e functional dimensions and corresponding size marks and colour codes for stools shall be as specified in the normative Annex E. Worksurfaces shall correspond to the height of stools as in Table E.3. Adjustable and multi-size furniture shall fulfil the requirements specified in Annex A, Annex B, Ann

46、ex C, Annex D or Annex E. The stature and popliteal height ranges shown in Table A.1, Table A.2, Table B.1, Table B.2, Table C.1 and Table D.1 do not include any allowance for shoes. All chair and table heights include an allowance for shoes. Assessment needs to be carried out according to EN 1729-1

47、 before being tested according to EN 1729-2. 5 Marking Chairs and tables in Annex A shall be marked as 0 to 7. Chairs and tables in Annex B shall be marked as B0 to B7. Standing-height tables in Annex C shall be marked as C0 to C7. Tall chairs in Annex D shall be marked as D0 to D7. Stools in Annex

48、E shall be marked as E0 to E7. The marking of fixed and adjustable chairs and tables shall be legible and indelible and shall include at least the following information: a) size mark or colour code or both, as specified in Annex A, Annex B, Annex C, Annex D or Annex E; b) marking on adjustable furni

49、ture of the size marks covered; c) name and/or trade name and/or mark and address of the manufacturer or his or her authorized representative in full or in abbreviated form, provided the abbreviation enables the manufacturer and/or his or her authorized representative to be identified; d) date of production by stating at least the year and month of production. Tall chairs shall also be marked with a reference where to find information on the table height they are intended to be used with. This information shall be provided on a label d