EN 1439-2008 en LPG equipment and accessories - Procedure for checking LPG cylinders before during and after filling《化石油气(LPG)设备和附件 LPG钢瓶罐装前 罐装中以及灌装后的检验程序[代替 CEN EN 14763 CEN EN 14.pdf

《EN 1439-2008 en LPG equipment and accessories - Procedure for checking LPG cylinders before during and after filling《化石油气(LPG)设备和附件 LPG钢瓶罐装前 罐装中以及灌装后的检验程序[代替 CEN EN 14763 CEN EN 14.pdf》由会员分享，可在线阅读，更多相关《EN 1439-2008 en LPG equipment and accessories - Procedure for checking LPG cylinders before during and after filling《化石油气(LPG)设备和附件 LPG钢瓶罐装前 罐装中以及灌装后的检验程序[代替 CEN EN 14763 CEN EN 14.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 1439:2008LPG equipment and accessories Procedure for checking LPG cylinders before, during and after fillingICS 23.020.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37

2、g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 1439:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2008ISBN 978 0 580 58613 2National forewordThis British Standard is the UK implementation of EN 1439:2008. It supersed

3、es BS EN 1439:2005, BS EN 14763:2005, BS EN 14794:2005 and BS EN 14913:2005, which are withdrawn. The UK participation in its preparation was entrusted to Technical Committee PVE/19, LPG containers and their associated fittings.A list of organizations represented on this committee can be obtained on

4、 request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Com

5、mentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1439February 2008ICS 23.020.30 Supersedes EN 1439:2005, EN 14763:2005, EN14794:2005, EN 14913:2005 English VersionLPG equipment and accessories - Procedure for checking LPGcylinders before, during and after fillingEquipements pour GPL et leurs a

6、ccessoires - Procdure devrification des bouteilles transportables et rechargeablespour GPL avant, pendant et aprs le remplissageFlssiggas-Gerte und Ausrstungsteile - Kontrollverfahrenfr ortsbewegliche, wiederbefllbare Flaschen frFlssiggas (LPG) vor, whrend und nach dem FllenThis European Standard wa

7、s approved by CEN on 6 January 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati

8、onalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and not

9、ified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malt

10、a, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploita

11、tion in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1439:2008: EEN 1439:2008 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Segregation of cylinders prior to filling 7 4.1 General7 4.2 Cylinders suita

12、ble for filling .7 4.3 Cylinders for periodic inspection.8 4.4 Cylinders requiring further assessment .8 5 Reassessment of cylinders 8 6 Filling conditions .8 6.1 Safe filling quantity8 6.2 Safe filling mixture and quality.8 6.3 Accuracy of filling equipment 9 6.4 Filling methods 9 7 Post filling ch

13、ecks .9 7.1 Check of filled amount 9 7.2 Action necessary for over / under-filled cylinders.9 7.3 Final checks .9 Annex A (normative) Specific requirements for welded and brazed steel LPG cylinders 10 Annex B (normative) Specific requirements for welded steel LPG cylinders in accordance with EN 1414

14、0 or equivalent standard .12 B.1 General12 B.2 Procedure for establishing rejection criteria carbon steel cylinders.12 B.3 Rejection criteria for stainless steel cylinders .14 Annex C (normative) Specific requirements for welded aluminium LPG cylinders.17 Annex D (normative) Specific requirements fo

15、r composite LPG cylinders19 D.1 Establishment of rejection criteria.19 D.1.1 General19 D.1.2 Procedure .19 D.2 Examples of rejection criteria.20 Annex E (normative) Safe filling conditions.26 Annex F (informative) Flow diagram of the checks before, during and after filling.27 Annex G (informative) I

16、nspection procedure for a particular design of protected cylinder .28 G.1 Scope and cylinder description .28 G.2 Cylinders suitable for filling .28 G.3 Cylinders for periodic inspection.28 G.4 Cylinders requiring further assessment .28 G.5 Reassessment of cylinders 28 Bibliography 31 BS EN 1439:2008

17、EN 1439:2008 (E) 3 Foreword This document (EN 1439:2008) has been prepared by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories”, the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication o

18、f an identical text or by endorsement, at the latest by August 2008, and conflicting national standards shall be withdrawn at the latest by August 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not

19、be held responsible for identifying any or all such patent rights. This European Standard has been submitted for reference into the RID (Regulations concerning the International Carriage of Dangerous Goods by Rail) and/or in the technical annexes of the ADR (European Agreement concerning the interna

20、tional carriage of Dangerous goods by Road). Therefore the standards listed in the normative references and covering basic requirements of the RID/ADR not addressed within the present standard are normative only when the standards themselves are referred to in the RID and/or in the technical annexes

21、 of the ADR. The main changes between this version of the standard and the 2005 version is that this version combines EN 1439:2005, EN 14763:2005, EN 14794:2005 and EN 14913:2005 into a single standard. This European Standard supersedes EN 1439:2005, EN 14763:2005, EN 14794:2005 and EN 14913:2005. A

22、ccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

23、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 1439:2008EN 1439:2008 (E) 4 Introduction This European Standard calls for the use of substances and procedures that can be injurious to he

24、alth if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this European Standard that the execution of its provisions is entrusted to appr

25、opriately qualified and experienced people. Where judgements are called for, it has been assumed that they are made by competent persons who have been trained specifically for the tasks. This standard is a combination of EN 1439:2005, with EN 14763:2005, EN 14794:2005 and EN 14913:2005. BS EN 1439:2

26、008EN 1439:2008 (E) 5 1 Scope This European Standard specifies the procedures to be adopted when checking transportable refillable LPG cylinders before, during and after filling. This European Standard applies to transportable refillable LPG cylinders of water capacity from 0,5 l up to and including

27、 150 l. This European Standard does not apply to cylinders permanently installed in vehicles, or to plant and filling equipment. This standard is applicable to the following: welded and brazed steel LPG cylinders with a specified minimum wall thickness (see EN 1442 and EN 12807 or an equivalent stan

28、dard); welded steel LPG cylinders without specified minimum wall thickness (see EN 14140 or an equivalent standard); welded aluminium LPG cylinders (see EN 13110 or an equivalent standard); composite LPG cylinders (see EN 14427 or an equivalent standard). Specific requirements for different types of

29、 cylinders are detailed in Annex A, Annex B, Annex C and Annex D. NOTE Rejection limits for a particular type of protected cylinder are given in Annex G. This standard is intended to be applied to cylinders complying with RID/ADR (including pi marked cylinders) and also to existing non RID/ADR cylin

30、der populations. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1440,

31、LPG equipment and accessories Periodic inspection of transportable refillable LPG cylinders EN 10028-7, Flat products made of steels for pressure purposes Part 7: Stainless steels EN 12816, Transportable refillable steel and aluminium LPG cylinders Disposal EN 13952, LPG cylinders - Filling procedur

32、es EN 14140, Transportable refillable welded steel cylinders for Liquefied Petroleum Gas (LPG) Alternative design and construction EN 14427:2004, Transportable refillable fully wrapped composite cylinders for Liquefied Petroleum Gases (LPG) - Design and Construction EN 14894, LPG Equipment and acces

33、sories - Cylinder and drum marking BS EN 1439:2008EN 1439:2008 (E) 6 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 LPG (liquefied petroleum gas) mixture of predominantly butane or propane with traces of other hydrocarbon gases clas

34、sified in accordance with UN number 1965, hydrocarbon gases mixture, liquefied, NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN numbers 1011 and 1978 may also be designated LPG. 3.2 competent person person who by a combination of training, experience and supervision, is

35、able to make objective judgements on the subject 3.3 competent body person or corporate body defined by the national authority, which by combination of appropriate qualification, training, experience and resources is able to make objective judgements on the subject 3.4 cylinder transportable, refill

36、able pressure receptacle with a water capacity from 0,5 l up to and including 150 l 3.5 protected cylinder metallic cylinder fully covered with a protection against impact and external corrosion so that the cylinder wall cannot be seen NOTE This is not a composite cylinder; see EN 14427 and Figure G

37、.1 3.6 casing permanently attached sleeve covering part of or the whole of the pressure containing envelope of a composite cylinder, usually incorporating a foot ring and a shroud NOTE Permanently attached means that casing cannot be removed during service without destruction, or by using special to

38、ols. 3.7 filling ratio ratio of the mass of gas introduced into a cylinder to the mass of water at 15 C that would fill the same cylinder fitted ready for use NOTE See Annex E for filling ratios. 3.8 reference temperature temperature used for the calculation of safe filling quantity NOTE See Annex E

39、 for reference temperatures. 3.9 filled to a level filled to a fixed level using a fixed liquid level device BS EN 1439:2008EN 1439:2008 (E) 7 3.10 filled by volume filled with a fixed volume of LPG 3.11 filled by mass filled with LPG using a weighing machine 3.12 filling plant establishment where f

40、illing and checking of LPG cylinders takes place 3.13 reconditioning major repairs to cylinders, which can include hot work, welding or de-denting carried out by specialists away from potential sources of flammable air/gas mixture 3.14 periodic inspection activities carried out at defined intervals,

41、 such as examining, measuring, testing or gauging the characteristics of a cylinder, comparing these with specified requirements as defined in EN 1440 and marking to attest conformity 3.15 tare mass sum of the mass of the empty cylinder, the mass of the valve including a dip tube where fitted, and t

42、he mass of all other parts that are permanently attached to the cylinder when it is being filled, e.g. fixed valve guard 4 Segregation of cylinders prior to filling 4.1 General Cylinders shall be checked and segregated into the categories specified in 4.2 to 4.4. A flow diagram of the checks before,

43、 during and after filling is given in Annex F. 4.2 Cylinders suitable for filling The cylinder shall be deemed suitable for filling if the following conditions apply: a) design code/specification is identifiable; b) tare indication and water capacity are known or marked; c) allowed quantity and iden

44、tification of the product (butane, propane or mixtures thereof, the properties of which were considered for the design of the cylinder) are indicated; d) cylinder is within the test date as determined from the marked manufacture date or periodic inspection date; e) cylinder does not have defects as

45、described in 4.4. For metallic cylinders, the inspection of the foot-ring for corrosion or damage shall determine the need for a more thorough external visual examination of the cylinder base; f) cylinder is fitted with a pressure relief valve, if required by the manufacturing standard. BS EN 1439:2

46、008EN 1439:2008 (E) 8 4.3 Cylinders for periodic inspection A cylinder shall be set aside for periodic inspection in accordance with EN 1440 when either of the following conditions apply: a) cylinder is out of test date; b) cylinder cannot be confirmed to be within test date. 4.4 Cylinders requiring

47、 further assessment A cylinder shall be set aside for further assessment (see Clause 5), if: a) tare indication of a cylinder, filled by mass, is not known or illegible; b) cylinder is judged to have unacceptable physical damage, corrosion or other defects; NOTE Defects and rejection limits are desc

48、ribed in Annex A, Annex B, Annex C, Annex D and Annex G. c) valve or pressure relief valve (if fitted) is damaged or has been previously identified as leaking. 5 Reassessment of cylinders Cylinders that have been set aside (see 4.4) shall be examined by a competent person who shall decide whether th

49、ey are suitable for filling or shall be sent for reconditioning where permitted by the appropriate annex or disposal in accordance with EN 12816 (where applicable). Cylinders that are intended to be filled by mass and where the indication of tare weight is missing or illegible shall be reassessed and have the indication of the tare weight applied in accordance with EN 14894. Leaking cylinders and cylinders with damaged or leaking valves shall be safely vented. Cylinders leaking through the body shall be disposed of in accordance with EN 12816 (where a