EN 14187-3-2017 en Cold applied joint sealants - Test methods - Part 3 Determination of self-levelling properties《冷用接缝密封胶-试验方法-第3部分 测定自动找平特性》.pdf

《EN 14187-3-2017 en Cold applied joint sealants - Test methods - Part 3 Determination of self-levelling properties《冷用接缝密封胶-试验方法-第3部分 测定自动找平特性》.pdf》由会员分享，可在线阅读，更多相关《EN 14187-3-2017 en Cold applied joint sealants - Test methods - Part 3 Determination of self-levelling properties《冷用接缝密封胶-试验方法-第3部分 测定自动找平特性》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 14187-3:2017Cold applied joint sealants Test methodsPart 3: Determination of self-levellingpropertiesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 14187-3:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14187-3

2、:2017. It supersedes BS EN 14187-3:2003 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/510/3, Materials for concrete roads.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not pu

3、rport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 87737 7 ICS 93.080.20 Compliance with a British Standard cannot confer immunity from legal obli

4、gations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 14187-3:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14187-3 March 2017 ICS 93.0

5、80.20 Supersedes EN 14187-3:2003English Version Cold applied joint sealants - Test methods - Part 3: Determination of self-levelling properties Mastics pour joints appliqus froid - Mthodes dessai - Partie 3 : Dtermination des proprits dautonivellement Kalt verarbeitbare Fugenmassen - Prfverfahren -

6、Teil 3: Bestimmung der selbstverlaufenden EigenschaftenThis European Standard was approved by CEN on 6 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without a

7、ny alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langu

8、age made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark

9、, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMM

10、ITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14187-3:2017 EBS EN 14187

11、-3:2017EN 14187-3:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus and materials 4 6 Conditioning 5 7 Procedure. 5 7.1 General 5 7.2 Determination of self-levelling properties using a horizontal mould at (5 2) C

12、 . 5 7.3 Determination of self-levelling properties using a mould inclined at 2,5 % slope at (23 2) C . 6 8 Test report . 6 BS EN 14187-3:2017EN 14187-3:2017 (E) 3 European foreword This document (EN 14187-3:2017) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat

13、of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September 2017. Attention is drawn t

14、o the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14187-3:2003. Apart from editorial changes no major changes have been made in this revision.

15、This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants Test methods Part 1: Determination of rate of cure. EN 14187-2, Cold applied joint sealants Test methods Part 2: Determination of tack free time. EN 14187-3, Cold applied joint sealants Te

16、st methods Part 3: Determination of self-levelling properties. EN 14187-4, Cold applied joint sealants Test methods Part 4: Determination of the change in mass and volume after immersion in test fuels and liquid chemicals. EN 14187-5, Cold applied joint sealants Test methods Part 5: Determination of

17、 the resistance to hydrolysis. EN 14187-6, Cold applied joint sealants Test methods Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid chemicals. EN 14187-7, Cold applied joint sealants Test methods Part 7: Determination of the resistance to flame. EN

18、14187-8, Cold applied joint sealants Test methods Part 8: Determination of the resistance to artificial weathering by UV-irradiation. EN 14187-9, Cold applied joint sealants Test methods Part 9: Function testing of joint sealants. According to the CEN-CENELEC Internal Regulations, the national stand

19、ards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

20、xembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14187-3:2017EN 14187-3:2017 (E) 4 1 Scope This European Standard describes a test method for determination of the self-levelling properties of

21、 cold applied normal and fuel resistant joint sealants for concrete pavements to be used in roads, airfields and other trafficked areas. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dat

22、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 6927, Buildings and civil engineering works - Sealants - Vocabulary (ISO 6927) 3 Terms and definitions For the purposes of this document, th

23、e terms and definitions given in EN ISO 6927 apply. 4 Principle The self-levelling properties of cold applied joint sealants are determined by pouring into moulds in horizontal and inclined positions. 5 Apparatus and materials 5.1 Mixing baker from polyethylene with a content of 250 ml. 5.2 Flat bla

24、ded spatula. 5.3 Mould (Figure 1) consisting of a channel with both ends closed and internal dimensions of (20 1) mm wide, (25 1) mm deep and (300 1) mm long. The channel shall be made of 1 mm to 2 mm thick aluminium, steel or plastic. 5.4 Wedge shaped pieces for positioning the mould in a horizonta

25、l position using a spirit level and at a (2,5 0,1) % slope with the level plane. 5.5 Micrometer, capable of measurement to 100 m, fitted with a ratchet. Other means of measuring this difference in depth are acceptable providing they are of equal accuracy. BS EN 14187-3:2017EN 14187-3:2017 (E) 5 Dime

26、nsions in millimetres Figure 1 Mould for the test of the self-levelling properties 6 Conditioning Condition the mixing baker (5.1), moulds (5.3), flat bladed spatula (5.2) and supplies of sealant samples in a refrigerated environment at (5 2) C for the test in the horizontal plane and at (23 2) C fo

27、r the test in inclined position for a period of 16 to 24 h. 7 Procedure 7.1 General For multi-component cold applied joint sealants, thoroughly mix appropriate quantities of base component with curing agent in the mixing baker following the manufacturers instruction within 2 min. One-component seala

28、nts can be applied directly from the pack. 7.2 Determination of self-levelling properties using a horizontal mould at (5 2) C 7.2.1 Pour the sealant into the mould in one continuous pour for 30 s along the axis of the mould at a height between 70 mm and 100 mm. Allow the material to flow freely to w

29、ithin 5 mm of the top of the mould. 7.2.2 Transfer the mould (see 5.3) immediately after filling, without vibration, to the refrigerated environment at (5 2) C and position in a horizontal plane using the spirit level (5.3) and leave to cure 48 h at (5 2) C. 7.2.3 Transfer the mould (5.3) to the mic

30、rometer (5.5). Set the probe in the channel at a convenient height above the sealant and zero the test equipment. Measure the depth of the sealant surface below the zero datum midway between the sides of the channel to an accuracy of 0,2 mm at the centre point of the mould and at points 25 mm, 50 mm

31、, 75 mm, 100 mm and 125 mm on either side of the centre point. BS EN 14187-3:2017EN 14187-3:2017 (E) 6 7.2.4 Subtract the highest reading from the lowest reading and record the difference to the nearest 0,5 mm. 7.3 Determination of self-levelling properties using a mould inclined at 2,5 % slope at (

32、23 2) C 7.3.1 Position the mould conditioned at (23 2) C horizontally using the spirit level (5.3). Apply the sealant to the mould as described in 7.2, but in this case overfill the mould and strike off the surplus material level to the mould edges using the flat bladed spatula. 7.3.2 Transfer the m

33、ould (5.3) immediately after filling and with a minimum of vibration in the environment capable of maintaining the test specimen at a temperature of (23 2) C and (50 5) % relative humidity and position at the (2,5 0,1) % slope. Leave to cure for 24 h at (23 2) C and (50 5) % relative humidity. 7.3.3

34、 As described in 7.2.3 measure the depth below an arbitrary datum at two points 20 mm from either end of the mould, each measurement midway between the channel sides. 7.3.4 Subtract the highest reading from the lowest reading and record the difference to the nearest 0,5 mm. 8 Test report The test re

35、port shall include the following information: a) reference to this European Standard; b) name and type of the cold applied joint sealant; c) batch of sealant from which the test specimens were produced; d) test results; e) any deviations from the specified test conditions; f) date of test. This page

36、 deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British St

37、andards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined

38、 through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our web

39、site at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need internatio

40、nal and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that

41、owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. Yo

42、u may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a

43、 sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Stand

44、ards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if y

45、ou wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are

46、 designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily

47、 so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members.

48、 You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intra

49、net. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to ben