EN 14187-1-2017 en Cold applied joint sealants - Test methods - Part 1 Determination of rate of cure.pdf

《EN 14187-1-2017 en Cold applied joint sealants - Test methods - Part 1 Determination of rate of cure.pdf》由会员分享，可在线阅读，更多相关《EN 14187-1-2017 en Cold applied joint sealants - Test methods - Part 1 Determination of rate of cure.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Cold applied joint sealants Test methodsPart 1: Determination of rate of cureBS EN 141871:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14187-1 June 2017 ICS 93.080.20 Supersedes EN 14187-1:2003English Versio

2、n Cold applied joint sealants - Test methods - Part 1: Determination of rate of cure Mastics pour joints appliqus froid - Mthodes dessai - Partie 1: Dtermination du taux de polymrisation Kalt verarbeitbare Fugenmassen - Prfverfahren - Teil 1: Bestimmung des Aushrtungsgrades This European Standard wa

3、s approved by CEN on 17 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat

4、ional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own lang

5、uage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece

6、, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NO

7、RMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14187-1:2017 ENational forewordThis British Standard is the UK implementation of EN 141871:2017. It superse

8、des BS EN 141871:2003, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/510/3, Materials for concrete roads.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include

9、all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 87743 8ICS 93.080.20Compliance with a British Standard cannot confer immunity from legal obligations.This Britis

10、h Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 141871:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14187-1 June 2017 ICS 93.080.20 Supersedes

11、 EN 14187-1:2003English Version Cold applied joint sealants - Test methods - Part 1: Determination of rate of cure Mastics pour joints appliqus froid - Mthodes dessai - Partie 1: Dtermination du taux de polymrisation Kalt verarbeitbare Fugenmassen - Prfverfahren - Teil 1: Bestimmung des Aushrtungsgr

12、ades This European Standard was approved by CEN on 17 April 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical

13、references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

14、a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mace

15、donia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISA

16、TION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14187-1:2017 EBS EN 141871:2017EN 14187-1:2017 (E) 2 Contents Page European f

17、oreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus and materials 4 6 Preparation of test specimens 4 7 Procedure. 5 8 Calculation and expression of results 6 9 Test report . 6 BS EN 141871:2017EN 14187-1:2017 (E) 3 European foreword This document (

18、EN 14187-1:2017) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2017, and c

19、onflicting national standards shall be withdrawn at the latest by December 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This

20、document supersedes EN 14187-1:2003. Apart from editorial changes no major changes have been made in this revision. This European Standard is one of a series of standards as listed below: EN 14187-1, Cold applied joint sealants Test methods Part 1: Determination of rate of cure. EN 14187-2, Cold app

21、lied joint sealants Test methods Part 2: Determination of tack free time. EN 14187-3, Cold applied joint sealants Test methods Part 3: Determination of self-levelling properties. EN 14187-4, Cold applied joint sealants Test methods Part 4: Determination of the change in mass and volume after immersi

22、on in test fuels and liquid chemicals. EN 14187-5, Cold applied joint sealants Test methods Part 5: Determination of the resistance to hydrolysis. EN 14187-6, Cold applied joint sealants Test methods Part 6: Determination of the adhesion/cohesion properties after immersion in test fuels and liquid c

23、hemicals. EN 14187-7, Cold applied joint sealants Test methods Part 7: Determination of the resistance to flame. EN 14187-8, Cold applied joint sealants Test methods Part 8: Determination of the resistance to artificial weathering by UV-irradiation. EN 14187-9, Cold applied joint sealants Test metho

24、ds Part 9: Function testing of joint sealants. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, For

25、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 141871:2017EN 14187-1:2017

26、 (E) 4 1 Scope This European Standard describes the determination of the rate of cure of cold applied joint sealants indicated by the build-up of the tensile modulus during the cure. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and

27、are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13880-12, Hot applied joint sealants Part 12: Test method for the manufacture of concrete test blo

28、cks for bond testing (recipe methods) EN ISO 6927, Buildings and civil engineering works Sealants Vocabulary (ISO 6927) EN ISO 8340, Building construction Sealants Determination of tensile properties at maintained extension (ISO 8340) 3 Terms and definitions For the purposes of this document, the te

29、rms and definitions given in EN ISO 6927 apply. 4 Principle The rate of cure of a cold applied joint sealant is determined as the relation between the tensile modulus at any time during cure and after complete cure of the test specimen. 5 Apparatus and materials 5.1 Concrete supports in accordance w

30、ith EN 13880-12 for the preparation of the test specimens, of dimensions as shown in Figure 1. Two concrete supports shall be used for each test specimen. 5.2 Spacers, (Figure 1) of dimensions 12 mm 12 mm 12,5 mm (Figure 1) for the preparation of test specimens. Two spacers shall be used for each te

31、st specimen. 5.3 Anti-adherent substrate for the preparation of the test specimens, on which the sealant does not adhere. 5.4 Tensile test machine capable of extending the test specimens at a rate of (5,5 0,5) mm/min. 6 Preparation of test specimens 6.1 Assemble two concrete supports (5.1) and two s

32、pacers (see 5.2) in accordance with Figure 1 and set up on the anti-adherent substrate (5.3). For the test six specimens are needed. 6.2 Follow the instructions of the sealant manufacturer whether a primer is to be used. 6.3 Condition the concrete supports, the spacers and the sealant for 4 h at (23

33、 2) C. Fill the volume between the concrete supports and spacers with sealant. 6.4 For multi-component cold applied joint sealants, thoroughly mix appropriate quantities of base component with curing agent following the manufacturers instruction. One-component joint sealants can be applied directly

34、from the pack. BS EN 141871:2017EN 14187-1:2017 (E) 5 The following precautions shall be taken: avoid the formation of air bubbles by filling from the bottom; ensure that no sealant is running out at the bottom; trim the sealant surface so that it is flush with the faces of the support and spacers.

35、Dimensions in millimetres Key 1 concrete support 2 cold applied joint sealant 3 spacers Figure 1 Test specimen 7 Procedure From the six test specimens three are conditioned in accordance with either method A or B of EN ISO 8340 (reference test specimens), see Table 1. Three of the test specimens are

36、 kept at the temperature of (23 2) C and (50 5) % relative humidity, see Table 1. Table 1 Conditioning methods for specimens Test specimens Reference test specimens Conditioning method (23 2) C EN ISO 8340, method A or B (50 5) % r. h Number of test specimens 3 3 BS EN 141871:2017EN 14187-1:2017 (E)

37、 6 After any time when the rate of cure has to be determined and according during the process of cure remove the spacers of the test specimens and place them in the tensile test machine and extend them of 100 % of the original width at a rate of (5,5 0,5) mm/min. Record a force/strain diagram. In th

38、e same way the reference test specimens are tested after completing conditioning method A or B. When method B is used, the reference test specimens will be tested after conditioning for 24 h at (23 2) C and (50 5) % relative humidity. 8 Calculation and expression of results Calculate the rate of cur

39、e, expressed in percentage as relation of the tensile modulus at 100 % extension of the test specimens to the reference test specimens, using the following equation: 12= 100MMMwhere M is the rate of cure, expressed in percent (%); M1is the arithmetic mean of the tensile modulus (100 % extension) of

40、the test specimen tested at any time during cure, expressed in newtons per square millimetre (N/mm2); M2is the arithmetic mean of the tensile modulus (100 % extension) of the reference test specimen after complete cure, expressed in newtons per square millimetre (N/mm2). 9 Test report The test repor

41、t shall include the following information: a) reference to this European Standard; b) name and type of the cold applied joint sealant; c) batch of sealant from which the test specimens were produced; d) rate of cure of the cold applied joint sealant; e) any deviations from the specified test conditi

42、ons; f) date of test. BS EN 141871:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products a

43、re published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefu

44、lly assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out

45、more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copi

46、es can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and c

47、opyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any

48、 portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standar

49、d purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard