EN 14070-2003 en Safety of machine tools - Transfer and special-purpose machines (Incorporates Amendment A1 2009 Incorporating corrigendum February 2010)《机床安全 传送装置和专用机械 包含修改件A1-200.pdf

《EN 14070-2003 en Safety of machine tools - Transfer and special-purpose machines (Incorporates Amendment A1 2009 Incorporating corrigendum February 2010)《机床安全 传送装置和专用机械 包含修改件A1-200.pdf》由会员分享，可在线阅读，更多相关《EN 14070-2003 en Safety of machine tools - Transfer and special-purpose machines (Incorporates Amendment A1 2009 Incorporating corrigendum February 2010)《机床安全 传送装置和专用机械 包含修改件A1-200.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 14070:2003Safety of machine tools Transfer and special-purpose machinesICS 25.080.01g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g4

2、7g36g58+A1:2009Incorporating corrigendum February 2010BS EN 14070:2003+A1:2009ISBN 978 0 580 70550 2Amendments/corrigenda issued since publicationDate Comments 31 December 2009 Implementation of CEN amendment A1:200931 August 2010 Implementation of CEN corrigendum February 2010. Reference to EN 954-

3、1 updated in Clause 2 and 5.2National forewordThis British Standard is the UK implementation ofEN 14070:2003+A1:2009, incorporating corrigendum February 2010. It supersedes BS EN 14070:2003 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by

4、 tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.NOTE The quality of some figures is not to the usual EN standard. Replacement drawings are not available at present.The UK participation in its preparati

5、on was entrusted to Technical Committee MTE/1, Machine tools.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Co

6、mpliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authorityof the Standards Policy and Strategy Committee on5 January 2005 BSI 2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14070:2003+A1 February 2009 ICS 25.080.01

7、 Supersedes EN 14070:2003English Version Safety of machine tools - Transfer and special-purpose machines Scurit des machines-outils - Machines transfert et machines spciales Sicherheit von Werkzeugmaschinen - Transfer- und Einzweck- oder Sondermaschinen This European Standard was approved by CEN on

8、24 July 2003 and includes Amendment 1 approved by CEN on 29 December 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog

9、raphical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

10、 a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irela

11、nd, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17

12、, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14070:2003+A1:2009: EIncorporating corrigendum February 20102 Contents page Foreword 3 0 Introduction 4 1 Scope 4 2 Normative references 5 3 Terms and definitio

13、ns .7 4 List of significant hazards 8 5 Safety requirements and/or protective measures . 13 6 Verification of safety requirements and/or protective measures 25 7 Information for use . 25 Annex A (normative) Guards on transfer and special purpose machines - Impact test method . 28 Annex B (informativ

14、e) Equipment for impact test . 32 B.1 Gun device . 32 B.2 Running the equipment 32 Annex C (informative) Illustrative figures used as examples 33 Annex D (normative) Noise emission measurement . 38 Annex ZA (informative) ! Relationship between this European Standard and the Essential Requirements of

15、 EU Directive 98/37/EC, amended by Directive 98/79/EC“ 40 Annex ZB (informative) ! Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 41 Bibliography . 42 BS EN 14070:2003+A1:2009EN 14070:2003+A1:2009 (E)3 Foreword This document (EN 14070:2003+A1:2

16、009) has been prepared by Technical Committee CEN/TC 143 “Machine tools - Safety”, the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflic

17、ting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-12-29. This document supersedes EN 14070:2003. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document ha

18、s been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential safety requirements of the Machinery Directive to determine safety for new transfer and special purpose machines. !For relationship with EC Directive(s), see inform

19、ative Annexes ZA and ZB, which are integral parts of this document.“ Annexes A and D are normative. Annexes B and C are informative. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to

20、implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer

21、land and United Kingdom. BS EN 14070:2003+A1:2009EN 14070:2003+A1:2009 (E)4 0 Introduction This European Standard is a type C standard as stated in 6.3.2 of EN 1070:1998. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of thi

22、s type C standard take precedence. Transfer and special purpose machines present a wide range of hazards due to the variety of processes and configurations with possible obstructions to vision on these machines, in particular, those hazardous events which result from contact with: Moving tools espec

23、ially when being rapidly rotated in spindles; Fast moving machine parts; Fast moving workpieces; Power operated mechanisms for workpiece handling, load or unload. The figures in annex C (informative) are examples only and are not intended to illustrate the only interpretation of the text. A list of

24、standards related to EN 14070 is given in the bibliography. 1 Scope 1.1 This standard specifies the technical safety requirements and protective measures to be adopted by persons undertaking the design, construction and supply (including information which must be provided for installation and disman

25、tling, with arrangements for transport and maintenance) of transfer and special purpose machines (see 3.1). These machines are designed to process only a pre-specified metal or analogous material workpiece, or limited family of similar workpieces by means of a predetermined sequence of machining ope

26、rations and process parameters. 1.2 This standard takes account of intended use, including reasonably foreseeable misuse, maintenance, cleaning, and setting operations. It specifies access arrangements to machining positions and manual load/unload stations (see 3.4). It presumes access to the machin

27、e from all directions. It describes means to reduce risks to operators and other exposed persons. 1.3 This standard also applies to transport devices for workpiece load/unload when they form an integral part of the machine. 1.4 This standard deals with significant hazards relevant to transfer and sp

28、ecial purpose machines when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). The safety requirements and/or protective measures to prevent or minimise those hazards identified in Table 1 and procedures for verification of these requirements or measures

29、are found in clause 5. Safety requirements and/or measures are not specified for: Fire and Explosion 1.5 Where machines employ processes which are covered by other standards (e.g. grinding, turning, forming, EDM, laser processing), the requirements of those standards should be applied (see Bibliogra

30、phy). 1.6 This standard applies to machines which are manufactured after publication of this standard by CEN. BS EN 14070:2003+A1:2009EN 14070:2003+A1:2009 (E)5 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normativ

31、e references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated referen

32、ces the latest edition of the publication referred to applies (including amendments). EN 292-1:1991, Safety of machinery - Basic concepts, general principles for design Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of machinery - Basic concepts, general principles for design Part 2:

33、Technical principles and specifications. EN 292-2:1991/A1:1995, Safety of machinery - Basic concepts, general principles for design Part 2: Technical principles and specifications; Amendment A1. EN 294:1992, Safety of machinery Safety distances to prevent danger zones being reached by the upper limb

34、s. EN 349, Safety of machinery Minimum gaps to avoid crushing of parts of the human body. EN 574, Safety of machinery Two-hand control devices Functional aspects Principles for design. EN 614-1, Safety of machinery - Ergonomic design principles Part 1: Terminology and general principles. EN 614-2, S

35、afety of machinery - Ergonomic design principles Part 2: Interactions between the design of machinery and work tasks. EN 626-1, Safety of machinery Reduction of risks to health from hazardous substances emitted by machinery Part 1 - Principles and specifications for machinery manufacturers. EN 811:1

36、996, Safety of machinery - Safety distances to prevent danger zones being reached by the lower limbs. EN 894-1, Safety of machinery - Ergonomic requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actuators. EN 894-

37、2, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays. EN 894-3:2000, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators. EN 953:1997, Safety of machinery Guards General req

38、uirements for the design and construction of fixed and movable guards. EN 954-1:1996, Safety of machinery - Safety-related parts of control systems Part l: General principles for design. EN 982:1996, Safety of machinery - Safety requirements for fluid power systems and their components Hydraulics. E

39、N 983:1996, Safety of machinery - Safety requirements for fluid power systems and their components Pneumatics. EN 999, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts of the human body. BS EN 14070:2003+A1:2009EN 14070:2003+A1:2009 (E)6 EN 1005-1, S

40、afety of machinery Human physical performance Part 1: Terms and definitions. EN 1005-2, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery. EN 1005-3, Safety of machinery Human physical performance Part 3: Recommended force limits for

41、 machinery operation. EN 1037:1995, Safety of machinery Prevention of unexpected start-up. EN 1050:1996, Safety of machinery - Principles for risk assessment. EN 1070:1998, Safety of machinery Terminology. EN 1088:1995, Safety of machinery - Interlocking devices associated with guards Principles for

42、 design and selection. EN 17601, Safety of machinery - Pressure sensitive protective devices Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors. EN 1837, Safety of machinery Integral lighting of machines. EN ISO 3744, Acoustics Determinatio

43、n of sound power levels of noise sources using sound pressure Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994). EN ISO 3746:1995, Acoustics Determination of sound power levels of noise sources using sound pressure Survey method using an enveloping measurement s

44、urface over a reflecting plane (ISO 3746:1995). EN ISO 4871, Acoustics Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996). EN ISO 7250, Basic human body measurements for technological design (ISO 7250:1996). EN ISO 9614-1, Acoustics Determination of soun

45、d power levels of noise sources using sound intensity Part 1: Measurement at discrete points (ISO 9614-1:1993). EN ISO 11202:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Survey method i

46、n situ (ISO 11202:1995). EN ISO 11204:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Method requiring environmental corrections (ISO 11204:1995). EN ISO 11688-1, Acoustics Recommended pra

47、ctice for the design of lownoise machinery and equipment Part 1: Planning (ISO/TR 11688-1:1995). EN ISO 11688-2, Acoustics Recommended practice for the design of lownoise machinery and equipment Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998). EN 60204-1:1997, Safety of

48、 machinery - Electrical equipment of machines Part 1: General requirements (IEC 60204-1:1997). EN 60825-1:1994/A1, Safety of laser products Part 1: Equipment classification, requirements and users guide; Amendment A1 (IEC 60825-1:1993/A1:1997) / Note: Endorsement notice EN 61000-62, Electromagnetic

49、compatibility (EMC) Part 6-2: Generic standards - Immunity for industrial environments (IEC 61000-6-2:1999, modified). BS EN 14070:2003+A1:2009EN 14070:2003+A1:2009 (E)7 EN 61000-6-4, Electromagnetic compatibility (EMC) Part 6-4: Generic standards - Emission standard for industrial environments (IEC 61000-6-4:1997, modified). EN 61310-3, Safety of machinery Indication, marking and actuation Part 3: Requirements for the location and operation of actuators (I