EN 13635-2001 en Irrigation Techniques - Localised Irrigation Systems - Terminology and Data to Be Supplied by the Manufacturer《灌溉技术 局部灌溉系统 术语和制造商提供的数据》.pdf

《EN 13635-2001 en Irrigation Techniques - Localised Irrigation Systems - Terminology and Data to Be Supplied by the Manufacturer《灌溉技术 局部灌溉系统 术语和制造商提供的数据》.pdf》由会员分享，可在线阅读，更多相关《EN 13635-2001 en Irrigation Techniques - Localised Irrigation Systems - Terminology and Data to Be Supplied by the Manufacturer《灌溉技术 局部灌溉系统 术语和制造商提供的数据》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Irrigation techniques - Localised irrigation systems - Terminology and data to be supplied by the manufacturer The European Standard EN 13635:2001 has the status of a British Standard ICs 01.040.65; 65.060.35 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS

2、EN 13635:2001 BS EN 13635:ZOOl National foreword This British Standard is the official English language version of EN 13635:ZOOl. The UK participation in its preparation was entrusted to Technical Committee AGEISO, Irrigation and drainage equipment, which has the responsibility to: - - aid enquirers

3、 to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on thi

4、s committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, o

5、r by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer

6、immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 September 2001 Summary of pages This document comprises a f

7、ront cover, an inside front cover, the EN title page, pages 2 to 16, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. IDate I Comments 0 BSI 21 September 2001 ISBN O 580

8、38171 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13635 August 2001 ICs 01.040.65; 65.060.35 English version Irrigation techniques - Localised irrigation systems - Terminology and data to be supplied by the manufacturer Techniques dirrigation - Installations avec irrigation localise - Ter

9、minologie et informations fournir par le fabricant Bewsserungsverfahren - Lokale Bewsserungssysteme - Terminologie und Angaben des Herstellers This European Standard was approved by CEN on 29 June 2001. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the con

10、ditions for giving this European Standard the status of a national standard without any alteration. Upto-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three o

11、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria.

12、 Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland. Italy, Luxembourg, Netherlands. Noway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMKTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FOR NORMUNG COMITE EUROPEEN DE NORMALISATION Management Cen

13、tre: rue de Stassart, 36 6-10% Brussels 0 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13635:2001 E EN 13635:ZOOl (E) Contents Foreword 3 Introduction . 4 1 2 3 3.1 3.1 . 1 3.1.2 3.1.3 3.1.4 3.2 3.2.1 3.2.2 3.2.3 3.3 3.3.1

14、3.3.2 3.3.3 3.3.4 3.4 3.4.1 3.4.2 3.5 3.6 3.7 3.7.1 3.7.2 Scope 5 Tenns and definitions 5 Localised irrigation installation components and minimum data to be supplied by the ma nufact u rer 9 Emitting devices . 9 Emitter . 9 Emitting pipes 10 Porous tubes and porous tapes . IO Microsprinklers and sp

15、rayers . 11 Filtration systems 11 Hydrocyclones . 11 Sand filters 11 Screen and disc filters . 12 Chemigation equipment 12 Fertilisation tanks 12 Venturi injectors . 12 Hydraulic injectors . 13 Electric injectors 13 Direct action . 13 Indirect action . 13 Pipes 13 Valves 14 Automatic control systems

16、 . 14 Irrigation controllers 14 Irrigation net managers . 15 Flow and pressure regulators . 13 Bibliography 16 2 . Foreword This European Standard has been prepared by Technical Committee CENTTC 334 “Irrigation techniques“, the secretariat of which is held by AFNOR. Within its programme of work CENT

17、TC 334 charged CENEC 334NVG 5 “Localised irrigation“ to prepare the following standard : EN 13635, Irrigation techniques - Localised irrigation systems - Terminology and data to be supplied by the manufacturer. This standard is related to others that will be drawn up for each system component (techn

18、ical characteristics and test methods). This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2002, and conflicting national standards shall be withdrawn at the latest by February 2002. Accordi

19、ng to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal,

20、Spain, Sweden, Switzerland and the United Kingdom. 3 EN 13635:2001 (E) Introduction The growing use of localised irrigation systems in farming and gardening has drawn attention to the need for a model on which to base the characteristics of these systems. This document is intended to enhance underst

21、anding between localised irrigation users and facility assemblers. 4 EN 13635:2001 (E) 1 Scope This European Standard specifies the technical and functional characteristics that shall be indicated by manufacturers of localised irrigation systems for user information to aid them in their choice of fa

22、cilities and materials. This standard is related to others that will be drawn up for each system component (technical characteristics and test methods). This European standard defines localised irrigation systems, characterising the various components which comprise them. 2 Terms and definitions For

23、 the purposes of this European Standard, the following terms and definitions apply: 2.1 localized irrigation method of irrigation whereby plants are watered by small amounts of water at low pressure applied to the soil, below or at the ground surface, without wetting the entire soil surface. It embr

24、aces several methods such as drip and microsprinkler irrigation 2.1 .I drip irrigation the application of water as drips or tiny streams through outlets 2.1.2 microsprinkler irrigation method of irrigation whereby water is applied in the form of a spray, mist or stream 2.2 chemigation application of

25、 chemicals together with irrigation water through an inducing system usually located in the head control 2.3 localised irrigation system unit generally comprised of components required for microirrigation, including: a) irrigation control head formed by: - main filters ; - devices for inducing chemi

26、cals ; - measuring equipment ; - controller. b) distribution and application networks ; c) sector valves and filters, pressure and flow regulators ; d) emitting devices. 5 EN 13635:2001 (E) 2.4 control head series of devices, usually located upstream of the installation, which perform one or several

27、 of the following operations: control and measure the water applied, add chemicals to the irrigation water, filter irrigation water, regulate pressure and volume, implement the established irrigation programme 2.5 lateral pipeline to which emitters are connected or integrated (when exuding systems a

28、re used, emitters are connected to the porous tube or the tape itself). 2.6 cubmain pipeline that supplies water to the laterals 2.7 irrigation subunit or irrigation block unit composed of a submain and its laterals, which operate simultaneously and have independent flow control 2.8 distribution net

29、work the water delivery pipelines that supply water from the head control to the subunits 2.9 irrigation sector a group of subunits that always operate simultaneously 2.10 irrigation area the total surface which is watered by a single control head 2.1 I emitting device device which emits water in a

30、localized area on or below the soil surface Depending on the sensitivity of their flow to pressure variation, emitting devices are classified as: 2.11.1 regulated emitting device emitting device of relatively constant emission rate at varying water pressures at the device inlet, within the limits sp

31、ecified by the manufacturer 2.1 1.2 unregulated emitting device emitting device whose emission rate varies according to the variation in water pressure at the inlet of the device Depending on the type of emitting device and the type of connection, emitters may be classed as: 2.11.3 in-line emitter e

32、mitter is inserted for installation between two lengths of pipe (irrigation lateral) 2.1 1.4 on-line emitter emitter is fixed directly or indirectly (e.g., by means of tubing) in the wall of the irrigation lateral 2.1 1.5 integrated emitter emitter which is inserted into the pipe during the manufact

33、uring process 6 EN 13635:2001 (E) 2.11.6 emitting pipe continuous pipe, hose or tubing with perforations or other hydraulic devices formed or integrated into the pipe during production and intended to emit water in the form of drops or continuous flow 2.1 1.7 drip tape collapsible emitting pipe 2.1

34、1.8 porous tube and porous tape flexible and porous lateral which emits a continuous flow of water all along its length 2.11.9 microsprin kler emitter which applies water in the form of a jet and has rotating arms 2.1 1 .IO sprayer or jet emitter which applies water in the form of spray, mist or str

35、eam and has no rotational movement Depending on the number of outlets, emitting devices may be classed as: 2.11 .I1 single emitter emitter which has one or more outlets, but only one flow regulating device, and which therefore has only one nominal emission rate for all of its outlets 2.11.12 multipl

36、e emitter emitter in which the output flow is divided and directed to several distinctly different locations each one with its own flow regulating device and therefore its own nominal emission rate Depending on their self-cleaning capability, emitting devices may be distinguished as: 2.11.13 self-cl

37、eaning emitter emitter which is able to clean unfiltered particles from its body without clogging it 2.12 nominal emission rate, q, unregulated emitting devices emission rate, in litres per hour, of the emitter at nominal pressure and at a water temperature of 23 OC, as specified by the manufacturer

38、 2.1 3 nominal emission rate, qn, regulated emitting devices emission rate, in litres per hour, of the emitter operating in the range of regulation and at a water temperature of 23 OC, as specified by the manufacturer 2.14 nominal emission rate, q., multiple emitter emission rate of each outlet 2.1

39、5 nominal emission rate, q, porous tube and porous tape emission rate, in litres per hour and per metre, of the emitting device at nominal pressure and at a water temperature of 23 OC, as specified by the manufacturer 7 EN 13635:2001 (E) 2.16 emission rate variation calculated using the following ex

40、pression: where q, is the nominal emission rate (specified by the manufacturer) ; - q is the mean emission rate at nominal pressure. 2.17 pressures 2.17.1 nominal test pressure, pn reference operating pressure at the inlet of an emitting device, given by the manufacturer 2.17.2 range of working pres

41、sures range of water pressures at the inlet of the emitting device, between and including the minimum working pressure, pmin ., and the maximum working pressure, p, . recommended by the manufacturer to ensure proper operation 2.17.3 range of regulation range of water pressures at the inlet of the re

42、gulated emitting device, in which each emitting unit discharges water within the range of emission rates specified by the manufacturer 2.18 manufacturers coefficient of variation coefficient calculated using the following formula: S cv (%)=xlOO 4 where s is the standard deviation of the discharge of

43、 the emitters in the sample, at the nominal test pressure ; - q is the mean discharge of emitters in the sample, at same pressure and temperature. NOTE In case of multiple-outlet emitters, each outlet is considered as an independent emitter. 2.19 filtration system device used to eliminate materials

44、suspended in the irrigation water, to prevent clogging or damage to the automation and control devices 2.19.1 h yd roc yc lo n e device in which suspended particles of density higher than water, are separated from the water by a centrifugal force resulting from the flow of water forced into a rotati

45、onal movement by any of several means 8 EN 13635:2001 (E) 2.19.2 sand filter medium depth filter in which the filtering medium consists of sand 2.19.3 screen filter filtration device in which the filtering medium is a mesh. 2.19.4 disc filter filtration device in which the filtering medium is compos

46、ed of discs with rough grooved or textured faces arranged one on top of the other to form a stack 3 Localised irrigation installation components and minimum data to be supplied by the manufacturer 3.1 Emitting devices 3.1.1 Emitter Model and manufacturer ; material ; nominal emission rate (I/h) ; no

47、minal emission rate variation ; manufacturers coefficient of variation ; nominal pressure (kPa or bar)l); range of working pressures ; range of regulation ; characteristic equation: q = Kp“ where q K p x is the emission rate (Vh) ; is the emitter discharge coefficient ; is the inlet pressure in the

48、emitter (kPa) ; is the emitter exponent : j) minimum recommended filtration ; k) dimension of the connection to the lateral. 1 kPa : 0,Ol bar 9 EN 13635:2001 (E) 3.1.2 Emitting pipes Model and manufacturer ; material ; indications for correct position as appropriate ; nominal emission rate (Vh) ; no

49、minal emission rate variation ; manufacturers coefficient of variation ; nominal pressure (kPa or bar) ; range of working pressures : range of regulation ; characteristic equation: q = Kp“ where 4 is the emission rate (Vh); K p is the emitter discharge coefficient ; is the inlet pressure in the emitter (kPa) ; X is the emitter exponent. k) minimum recommended filtration : I) internal diameter ; m) wall thickness ; n) spacing between emitting units. 3.1.3 a) Model and manufacturer ; b) material; Porous tubes and porous tapes c) nominal emission rate (1.h-l.m-l or 1.h-I per