EN 13618-2016 en Flexible hose assemblies in drinking water installations - Functional requirements and test methods《饮用水设施中的挠性软管组件-功能要求和试验方法》.pdf

《EN 13618-2016 en Flexible hose assemblies in drinking water installations - Functional requirements and test methods《饮用水设施中的挠性软管组件-功能要求和试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 13618-2016 en Flexible hose assemblies in drinking water installations - Functional requirements and test methods《饮用水设施中的挠性软管组件-功能要求和试验方法》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 13618:2016Flexible hose assemblies indrinking water installations Functional requirements andtest methodsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 13618:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13618

2、:2016. Itsupersedes BS EN 13618:2011 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/504, Water supply.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all th

3、e necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 93160 4ICS 23.040.70; 91.140.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This Bri

4、tish Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/Corrigenda issued since publicationDate Text affectedBS EN 13618:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13618 December 2016 ICS 23.040.70; 91.140.60 Supersed

5、es EN 13618:2011English Version Flexible hose assemblies in drinking water installations - Functional requirements and test methods Tuyaux flexibles pour installations deau potable - Exigences fonctionnelles et mthodes dessai Flexible Schlauchverbindungen in Trinkwasser-Installationen - Funktionsanf

6、orderungen und Prfverfahren This European Standard was approved by CEN on 15 August 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li

7、sts and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde

8、r the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Y

9、ugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROP

10、EN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13618:2016 EBS EN 13618:2016EN 13618:2016 (E) 2 Contents Page

11、European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Requirements . 8 4.1 Materials . 8 4.1.1 General 8 4.1.2 Chemical and hygienic requirements 8 4.1.3 Hoses 8 4.1.4 Fittings and sleeves 8 4.1.5 Braiding 8 4.1.6 Sealings . 8 4.2 Functional requirements 8 4.2.1 Gene

12、ral 8 4.2.2 Fittings 9 4.2.3 Hose assemblies 12 5 Designation. 15 6 Marking 15 Annex A (normative) Tests on fittings . 17 A.1 Dimensions and thread control 17 A.2 Ammonium test. 17 A.3 Tightening test 17 A.3.1 Test samples 17 A.3.2 Procedure 17 A.4 Bending test . 18 A.4.1 Test samples 18 A.4.2 Proce

13、dure 18 Annex B (normative) Hose assembly tests . 21 B.1 Flow rate test . 21 B.1.1 Test samples 21 B.1.2 Procedure 21 B.2 Ageing treatment by hot storage 22 B.2.1 Test samples 22 B.2.2 Procedure 22 B.3 Tensile test . 22 B.3.1 Test samples 22 B.3.2 Procedure 22 B.4 Hydrostatic pressure test 22 B.4.1

14、Test samples 22 B.4.2 Procedure 22 B.5 Hydraulic performance and durability test 23 B.5.1 Test samples 23 B.5.2 Test conditions 23 B.5.3 Procedure 23 BS EN 13618:2016EN 13618:2016 (E) 3 B.6 Test of resistance to pressure jumps . 24 B.6.1 Test samples . 24 B.6.2 Test conditions 24 B.6.3 Procedure 24

15、B.7 Temperature cycling test . 24 B.7.1 Test samples . 24 B.7.2 Procedure 25 B.8 Corrosion resistance test . 25 B.8.1 Test samples . 25 B.8.2 Procedure 25 B.9 Bending test 25 B.9.1 Test samples . 25 B.9.2 Procedure 25 B.10 Test of resistance to frost 27 B.10.1 Test samples . 27 B.10.2 Procedure 27 A

16、nnex C (informative) Surveillance testing . 28 Bibliography . 29 BS EN 13618:2016EN 13618:2016 (E) 4 European foreword This document (EN 13618:2016) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given th

17、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be withdrawn at the latest by June 2017. Attention is drawn to the possibility that some of the elements of this document may be the sub

18、ject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13618:2011. EN 13618:2016 includes the following significant technical changes with respect to EN 13618:2011: a) the stress corrosion testing is carried

19、out with ammonium only; b) requirement ad test method for resistance of seat of female fitting are deleted; c) in Table 8, specific minimum flow rates and minimum bore diameters are left open; d) for testing the pressure jumps resistance, detailed specification for DN and applied test pressure are g

20、iven; e) new test methods for corrosion resistance and UV resistance are introduced; f) in Table A.2, the dimensions C are reduced; g) in hydraulic performance and durability test, the number of impulses is reduced; h) the recommended surveillance testing of specific functional requirements is intro

21、duced. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fran

22、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13618:2016EN 13618:2016 (E) 5 1 Scope This European Standard specifies the

23、 requirements and test methods for materials, dimensions and function for flexible hose assemblies for drinking water installations, braided or not, designed for use with drinking water with an allowable maximum operating pressure (PMA) of 1 MPa and maximum operating temperature 70 C to connect sani

24、tary tap ware, heaters and similar appliances. NOTE Flexible hose assemblies intended to be used as integral parts of electrical appliances are covered by EN 61770 1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensabl

25、e for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 248, Sanitary tapware General specification for electrodeposited coatings of Ni-Cr EN 806-2, Specification for ins

26、tallations inside buildings conveying water for human consumption Part 2: Design EN 1254-2, Copper and copper alloys Plumbing fittings Part 2: Fittings with compression ends for use with copper tubes EN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use

27、 with plastics pipes EN 1254-4, Copper and copper alloys Plumbing fittings Part 4: Fittings combining other end connections with capillary or compression ends EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1)

28、 EN ISO 1456, Metallic and other inorganic coatings Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium (ISO 1456) EN ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics

29、materials in pipe form by extrapolation (ISO 9080) EN ISO 15875-2, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 2: Pipes (ISO 15875-2) EN ISO 15876-2, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 2: Pipes (IS

30、O 15876-2) EN ISO 22391-2, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes (ISO 22391-2) EN ISO 30013:2011, Rubber and plastics hoses Methods of exposure to laboratory light sources Determination of changes in colour, a

31、ppearance and other physical properties (ISO 30013:2011) ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ISO 6957, Copper alloys Ammonia test for stress corrosion resistance BS EN 13618:2016EN 13618:2016 (E) 6 3 Terms and defin

32、itions For the purposes of this document, the following terms and definitions apply. 3.1 hose assembly flexible hose with or without braiding and furnished at one or both ends with a fitting or an integrated flange, or adapted to meet the use of appropriate fittings Note 1 to entry: See Figure 1: Ke

33、y 1 internal hose 2 braiding 3 sleeve 4 fitting 5 outer layer (optional) Figure 1 Example of hose assembly components 3.2 internal hose internal part of the hose assembly 3.3 braiding external applied reinforcement intended to achieve the pressure resistance and to protect the internal hose from blu

34、nt impact, rubbing or constriction, usually achieved with stainless steel or synthetic wires 3.4 sleeve component used to fix internal hose mechanically to fittings 3.5 fitting component attached to the end of the flexible hose to facilitate connection to appliances Note 1 to entry: Examples of shap

35、e and designation of the fitting are given in Table 1: BS EN 13618:2016EN 13618:2016 (E) 7 Table 1 Shape and designation of fittings Type Shape Designation 1 Fixed male fitting in accordance with EN ISO 228-1 or ISO 7-1 2 Revolving male fitting in accordance with EN ISO 228-1 or ISO 7-1 3 Straight f

36、emale fitting in accordance with EN ISO 228-1 or ISO 7-1 4 Elbow female fitting in accordance with EN ISO 228-1 5 Compression biconical fitting 6 Fitting with plain and short smooth tube with recess 7 Fitting with plain and short smooth tube without recess 8 Metric male thread fitting 9 Special appl

37、ications BS EN 13618:2016EN 13618:2016 (E) 8 4 Requirements 4.1 Materials 4.1.1 General All materials used shall be chemically compatible with each other and with the water supplied (following the common chemical reaction and/or corrosion knowledge of the materials concerned). 4.1.2 Chemical and hyg

38、ienic requirements All materials coming into contact with water intended for human consumption shall not present a health risk or cause any change in the drinking water in terms of quality, appearance, smell or taste. Products intended for use in drinking water supply systems should comply with nati

39、onal regulations and testing arrangements, where they exist, that ensure fitness for contact with drinking water. 4.1.3 Hoses 4.1.3.1 Internal hoses Internal hoses can be made of elastomeric, thermoplastics and plastics materials. 4.1.3.2 Non-braided hoses Non-braided hoses shall comply with long-te

40、rm stress requirements in accordance with EN ISO 15875-2, EN ISO 15876-2 and EN ISO 22391-2 when evaluated in accordance with EN ISO 9080. 4.1.4 Fittings and sleeves Fittings and sleeves with exception of plain end fittings with and without recess shall be manufactured from corrosion-resistant mater

41、ials. Sleeves and plain end fittings with and without recess shall be made of corrosion-resistant metallic materials only. Aluminium materials are not allowed. 4.1.5 Braiding Braiding shall be made of stainless steel wires or plastics wires/bands. Braiding made of stainless steel can have integrated

42、 plastic wires/bands for colour coding only. In case of braiding made of plastics materials, the hose assembly shall be UV resistant in accordance with 4.2.3.10. 4.1.6 Sealings Sealing materials shall demonstrate the compliance with 4.2. 4.2 Functional requirements 4.2.1 General The separate compone

43、nts and hose assemblies shall comply and be tested to the functional requirements as indicated in Table 2. The surveillance testing for specific functional requirements is recommended. If the surveillance testing is carried out, this should be done in accordance with Annex C. BS EN 13618:2016EN 1361

44、8:2016 (E) 9 Table 2 List of characteristics for separate components and for hose assemblies Characteristic Requirement subclause Test method clause/subclause Fittings and sleeves Dimensions 4.2.2.1 A.1 Stress corrosion 4.2.2.2 A.2 Resistance to tightening torque of fitting 4.2.2.3 A.3 Resistance to

45、 bending 4.2.2.4 A.4 Hose assembly Length of hose assembly 4.2.3.1 4.2.3.1 Flow rate 4.2.3.2 B.1 Tensile stress resistance 4.2.3.4 B.3 Leak tightness under internal hydrostatic pressure 4.2.3.3 B.4 Pressure cycling resistance 4.2.3.5 B.5 Resistance to pressure jumps 4.2.3.6 B.6 Temperature cycling r

46、esistance 4.2.3.7 B.7 Frost resistance 4.2.3.8 B.10 Resistance to corrosion 4.2.3.9 B.8 Flexibility 4.2.3.11 B.9 UV resistance 4.2.3.10 4.2.3.10 4.2.2 Fittings 4.2.2.1 Dimensions Fittings shall comply with the appropriate dimensions as stated in Tables 3, 4 and 5 when checked in accordance with A.1,

47、 and with the relevant functional requirements as stated in EN 1254-2, EN 1254-3 and EN 1254-4. Fittings with push-fit ends and with press end for metallic tubes shall comply with requirements of this standard. BS EN 13618:2016EN 13618:2016 (E) 10 Table 3 Fixed fittings with external thread Threadin

48、g th in accordance with Gauge length in accordance with ISO 7-1 Minimum useful threading length l in accordance with EN ISO 228-1 ISO 7-1 EN ISO 228-1 mm mm R 1/4 G 1/4 B 8,4 6 R 3/8 G 3/8 B 8,8 7 R 1/2 G 1/2 B 11,4 7 R 3/4 G 3/4 B 12,7 8,5 R 1 G 1 B 14,5 9,5 R 5/4 G 5/4 B 16,8 11 Table 4 Female fit

49、tings with nut Threading th in accordance with EN ISO 228-1 Minimum useful threading length l mm G 1/4 4 G 3/8 5 G 1/2 6 G 3/4 7 G 1 8 G 1 1/4 10 BS EN 13618:2016EN 13618:2016 (E) 11 Table 5 Plain end fittings with and without recess External diameter mm Minimum length l mm Wrench size E Inner dia-meter h mm Wall thick- ness t mm d1d2l1l2l3mm 8 0,1 7,7+0,050,17 25 5 10 6,3 0,75 10 0,1 9,7+0,050,17 25 5 11 8 0,8 12 0,1 11,7+0,050,17 25 7 13 10 0,9 15 0,1 14,7+0,050,110 30 7 17 13 1,4 22 0,