EN 13160-6-2016 en Leak detection systems - Part 6 Sensors in monitoring wells《检漏系统-第6部分 监测井中传感器》.pdf

《EN 13160-6-2016 en Leak detection systems - Part 6 Sensors in monitoring wells《检漏系统-第6部分 监测井中传感器》.pdf》由会员分享，可在线阅读，更多相关《EN 13160-6-2016 en Leak detection systems - Part 6 Sensors in monitoring wells《检漏系统-第6部分 监测井中传感器》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 13160-6:2016Leak detection systemsPart 6: Sensors in monitoring wellsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 13160-6:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13160-6:2016.The UK participation in it

2、s preparation was entrusted to TechnicalCommittee PVE/393/2, Leak detection devices.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its c

3、orrectapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 86639 5ICS 23.020.01; 23.040.99; 29.260.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStan

4、dards Policy and Strategy Committee on 31 July 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 13160-6:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13160-6 July 2016 ICS 23.020.01; 23.040.99; 29.260.20 English Version Leak detection systems - Part 6:

5、Sensors in monitoring wells Systmes de dtection de fuites - Partie 6: Systmes statiques de dtection de fuites dans les puits pizomtriques Leckanzeigesysteme - Teil 6: Sensoren in berwachungsschchten This European Standard was approved by CEN on 8 April 2016. CEN members are bound to comply with the

6、CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management

7、Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

8、 the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

9、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All r

10、ights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13160-6:2016 EBS EN 13160-6:2016EN 13160-6:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 General 4 5 Monitoring wells 4 6 Disc

11、riminating liquid sensors 6 7 Vapour sensor 7 8 Alarm device . 7 BS EN 13160-6:2016EN 13160-6:2016 (E) 3 European foreword This document (EN 13160-6:2016) has been prepared by Technical Committee CEN/TC 393 “Equipment for storage tanks and for filling stations”, the secretariat of which is held by D

12、IN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn at the latest by January 2017. Attention is drawn to the possibility that so

13、me of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard Leak detection systems consists of 7 parts: Part 1: General principles Part 2: Requirements and test/assessm

14、ent methods for pressure and vacuum kits Part 3: Requirements and test/assessment methods for liquid systems for tanks Part 4: Requirements and test/assessment methods for sensor based leak detection systems Part 5: Requirements and test/assessment methods for in-tank gauge systems and pressurized p

15、ipework systems Part 6: Sensors in monitoring wells Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

16、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

17、 Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13160-6:2016EN 13160-6:2016 (E) 4 1 Scope This European Standard specifies the requirements for leak detection systems class V for use with systems designed for fuels that are flammable, having a flash poi

18、nt up to but not exceeding 100 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the refere

19、nced document (including any amendments) applies. EN 131601:2016, Leak detection systems Part 1: General principles EN 13160-3:2016, Leak detection systems Part 3: Requirements and test/assessment methods for liquid systems for tanks EN 131604:2016, Leak detection systems Part 4: Liquid and/or vapou

20、r sensor systems for use in leakage containments or interstitial spaces EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13160-1:2016 apply. 4 General This type of l

21、eak detection kit is classified according to EN 13160-1:2016 as class V. The general requirements on leak detection systems according to Clause 5 of EN 13160-1:2016 shall be met. 5 Monitoring wells Monitoring wells shall be installed in the ground, with a minimum diameter of 300 mm. Where liquid sen

22、sors are used, the monitoring well shall extend from the ground level to a depth of at least 1,0 m below: a) the lowest normal groundwater level or b) the lowest point of any tank or pipe, whichever is lower. Where vapour sensors are used, the monitoring well shall extend from the ground level to a

23、depth of at least 1,0 m below the lowest point of any tank or pipe. Where there is the risk that the normal groundwater level will fall below the point 1,0 m above the lowest perforation opening of a monitoring well, vapour sensors shall be used. Shall have a casing which is perforated uniformly, bo

24、th vertically and circumferentially, which extends from ground level to the lowest point of the well. The pattern of perforations shall be designed to permit entry of liquid into the well at any height, but shall be small enough to prevent inflow of the surrounding ground material. BS EN 13160-6:201

25、6EN 13160-6:2016 (E) 5 The casing should be constructed with sufficient strength so that the well is not distorted under pressure of the surrounding ground, whether empty or full of liquid. Shall have a top cap sealed to a minimum standard of IP 66 according to EN 60529:1991, to prevent entry into t

26、he well of surface water, liquid spills etc. The cap shall be removable to allow inspection of the contents of the well. Shall have a bottom seal fixed permanently to the casing to prevent the entry of ground material during installation or in service. Sufficient monitoring wells should be installed

27、 around a system and positioned to ensure that any leakage of stored product from any part of the system will reach a monitoring well. Specification for the monitoring well casing: Size: minimum 100 mm inner diameter Wall thickness: minimum 6,0 mm Material: e.g. Polyethylene (PE) or equivalent Slots

28、: 0,4 to 0,6 mm wide 45 to 55 mm long equally spaced around the circumference of the casing 6,8 mm vertical spacing. The casing shall be closed at the bottom. In ground conditions where fine soil is present that would pass through the slots a filter screen should be fitted of such size as to prevent

29、 passage of the ground material. Monitoring wells should not be used where the ground material does not allow adequate permeation of stored product or vapour between the storage system and the monitoring well. Monitoring wells should be surrounded by filler sand or pea shingle to at least 300 mm dia

30、meter. Construction of a monitoring well, see Figure 1. BS EN 13160-6:2016EN 13160-6:2016 (E) 6 Dimensions in millimetres Key 1 lockable well seal (IP 66 according to EN 60529:1991) 2 monitoring well cover 3 unperforated pipe in sealed area 4 groundwater level 5 ground material 6 perforated casing 7

31、 filler sand or pea shingle 8 sealed to prevent contamination from above 9 concrete or bitumen Figure 1 Construction of monitoring wells 6 Discriminating liquid sensors The liquid sensor of category 2 shall meet the requirements according to 4.1.2 and 4.1.4, if applicable and 4.1.5, 4.2.1 and 4.2.2

32、of EN 131604:2016. Shall be capable of differentiating between water and the stored product, and shall not give an alarm condition in the presence only of water. If the liquid sensor requires the presence of groundwater for correct operation, and the level of groundwater falls below the minimum or r

33、ises above the maximum necessary for correct operation, an alarm condition shall result. BS EN 13160-6:2016EN 13160-6:2016 (E) 7 7 Vapour sensor The vapour sensor shall meet the requirements according to 4.1.2 to 4.1.4, if applicable and 4.1.5, 4.2.1 and 4.2.2 of EN 131604:2016. The alarm device sha

34、ll enter an alarm condition in the presence of vapour of the stored product. Vapour sensors used in any location where there is the risk that they could become submerged in water or any other liquid shall sound an alarm on becoming submerged. 8 Alarm device An alarm shall be indicated on detecting t

35、he presence of stored product or on detecting the absence of water, when this is required for correct operation. An alarm device according to EN 13160-3:2016, 4.1.3.5 shall be provided. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for prepari

36、ng British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, g

37、overnment, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and a

38、cross all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Bu

39、ying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations

40、, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standa

41、rdization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display t

42、he standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard

43、 may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard

44、 copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money

45、 by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further informatio

46、n on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards dev

47、elopments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards w

48、hen theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With update

49、s supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowl