EN 13086-2000 en Lead and Lead Alloys - Lead Oxides《铅及铅合金 氧化铅》.pdf

《EN 13086-2000 en Lead and Lead Alloys - Lead Oxides《铅及铅合金 氧化铅》.pdf》由会员分享，可在线阅读，更多相关《EN 13086-2000 en Lead and Lead Alloys - Lead Oxides《铅及铅合金 氧化铅》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN 13086-ENGL 2000 = 1624bb9 0872900 b43 BRITISH STANDARD Lead and lead alloys - Lead oxides “he European Standard EN 130862000 has the status of a British Standard ICs 77.150.60 35 EN 13086:ZOOO NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMIITED BY COPYRIGET LAW STD-BSI BS EN L30b-ENG

2、L 2000 I1624667 O727OL 5T S BS EN 130862000 Amd. No. Date This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 September 2000 Comments 0 BSI 042000 ISBN O 580 3616

3、2 4 National foreword This British Standard is the official English language version of EN 13086:2000. The UK participation in its preparation was entrusted to Technical Committee “EB2, Lead and lead alloys, which has the responsibility to: - aid enquirers to understand the text; - present to the re

4、sponsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of orghtions represented on this committee can be obtained on request to its

5、secretaxy. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Stan

6、dards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from iegai obligations. Summary of pa

7、ges This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 18, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. STDmBSI BS EN L30Bb-ENGL 2000 Lb24bb9 0872902 416 1111 EUROPEAN

8、STANDARD NORME EUROPENNE EUROPASCHE NORM EN 13086 June 2000 ICs 77.150.60 English version Lead and lead alloys - Lead oxides Plomb et alliages de plomb - Oxydes de plomb Blei und Bleilegierungen - Bleioxide This European Standard was approved by CEN on 19 May 2000. CEN members are bound to comply wi

9、th the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards may be obtained on application to the Central Secretar

10、iat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tmslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as tie official v

11、ersions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES

12、 KOMITEE FOR NORMUNG COMIT EUROPEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 8-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13086:2000 E STDOBSI BS EN 1308b-ENGL 2000 1624667 0872903 352 Page

13、 2 EN 13086:2000 Contents Foreword -. 3 1 Scope - 4 2 Normative references 4 3 Terms and definitions - 4 4 Production process .- . 5 5 Requirements . - 5 6 Quality control - . 8 7 Test methods 8 8 Ordering information . - . 9 9 Labelling -. 9 Annex A (normative) Determination of free lead in lead ox

14、ides . 10 Annex B (normative) Determination of lead dioxide in red lead and litharge . 12 Annex C (normative) Determination of oversize residue by water method using a manual sieving procedure .- 15 Annex D (normative) Determination of sulfuric acid absorption index in battery oxides . 17 . . Q BSI

15、09-2000 STD-BSI BS EN 13086-ENGL ZOO0 Lb24bb7 0872904 299 Page 3 EN 13086:2000 Foreword This European Standard has been prepared by Technical Committee CENITC 306 “Lead and lead alloys“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standar

16、d, either by publication of an identical text or by endorsement, at the latest by December 2000, and conflicting national standards shall be withdrawn at the latest by December 2000. The annexes A, B, C and D are normative. According to the CENICENELEC Internal Regulations, the national standards or

17、ganizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Q BSI 09-2000 STD-

18、BSI BS EN L3086-ENGL 2000 Lb24669 Oi872905 L25 I Page 4 EN 13086:2000 1 Scope This European Standard specifies the requirements, acceptance tolerances and chemical and physical test procedures for lead oxides, including litharges (powder or granulated), battery oxides (Barton or Mill) and crystal re

19、d lead. WARNING Lead and lead compounds are toxic by inhalation andlor ingestion. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publicat

20、ions are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies (including amen

21、dments). EN 23923-2, Metallic powders - Determination of apparent density - Part 2 : Scott volumeter method (IS0 3923-2 : 1981). EN IS0 787-1 1, General methods of test for pigments and extenders - fart 11 : Determination of tamped volume and apparent density after tamping (/SO 787-7 1:1981). 3 Term

22、s and definitions For the purpose of this European Standard, the following terms and definitions apply : 3.1 lead oxide product obtained from oxidation of lead metal with air 3.2 battery oxide product obtained from partial oxidation of lead metal with air and composed of lead monoxide (PbO) and lead

23、 metal (Pb) NOTE There are two varieties used in batteries : Barton (see 3.2.1) and Mill (see 3.2.2). 3.2.1 Barton type of battery oxide obtained from oxidation of molten lead metal with air 3.2.2 Mill type of battery oxide obtained from oxidation of lead metal with air together with a grinding proc

24、ess 3.3 litharge product composed of lead monoxide (PbO) and obtained from oxidation of lead metal, supplied either as powder or granulated 3.4 red lead product essentially composed of lead(l1)-lead(lV) oxides (2PbO.PbQ) (also known as lead orthoplumbate, trilead tetroxide, minium, etc.) obtained fr

25、om oxidation of lead metal Q BSI 09-2000 STDaBSI BS EN 130Bb-ENGL ZOO0 W Lb24bb9 0672906 Ob1 W Requirements PbO content (mass fraction) Page 5 EN 13086:2000 Units Values % 65 to 82 4 Production process The process for the production of lead oxides shall be left to the discretion of the producer. Tam

26、ped density Residue in sieve over 63 pm 5 Requirements g/cm3 2,9 to 33 % 0,5 max. The requirements for lead oxides differ, depending on the type and the application of the oxide. The lead oxides shall be in accordance with the requirements given in the relevant table (see Tables 1 to 7). The test me

27、thod shall be in accordance with the relevant method (see clause 7). Requirements PbO content (mass fraction) NOTE 1 can be specified in the order by agreement between the supplier and the purchaser. Additional requirements or a range of values within, but narrower than, those stated in this Europea

28、n Standard Units Values % 65 to 82 NOTE 2 In all cases, the level of impurities is a consequence of impurities present in the lead used. Free Pb content (mass fraction) Apparent density (Scott) 5.1 Battery oxides % 18 to 35 g/cm3 1 ,o to 2,o Table 1 - Battery oxide - Mill type Tamped density Residue

29、 in sieve over 63 pm g/cm3 3 to 4 % 0,5 max. Table 2 - Battery oxide - Barton type Q BSI 09-2000 STDaBSI BS EN L308b-ENGL 2000 m Lb24bb9 0872907 TTB Requirements Units PbO content (mass fraction) % PbOi content (mass fraction) % Free Pb content (mass fraction) % Page 6 EN 13086:2000 Values 993 min.

30、0,05 max. 0,05 max. 5.2 Litharges Apparent density (Scott) Table 3 - Litharge - Powder g/cm3 1,8 to 2,6 I Description Tamped density Residue in sieve over 63 urn g/cm3 3,7 to 5,1 % 0,3 max. Characteristics a Units Values Molecular mass Melting point I “C I 886 g/mol 223,2 Requirements PbO content (m

31、ass fraction) Free Pb content (mass fraction) Characteristics a Table 4 - Litharges - Granulated Units Values % 993 min. % 0,05 max. Units Values Description Denomination Litharge - granulated Colour Yellow/orange Formulae PbO Melting point Molecular mass “C 886 g/mol 223,2 a The following character

32、istics are given for information only. Q BSI 09-2000 STD-BSI BS EN 1308b-ENGL 2000 m lb24bb9 0872908 934 m Requirements PbO content (mass fraction) Page 7 EN 13086:2000 Units Values % 28,3 max. 5.3 Red lead oxides Pb02 content (mass fraction) Pb304 content (mass fraction) Table 5 - Red leads for bat

33、tery % 25,O min. % 71,7 min. I Description I Apparent density (Scott) Tamped density I Denomination g/crn3 1,l to 1,9 g/crn3 2,7 to 4,O Red lead (battery) Residue in sieve over 63 pm Characteristics a I Cotour Orannehed I % 2 max. Units Values I Formulae Melting point Molecular mass Pb304(2PbO Pb02)

34、 “C 500 g/mol 685,6 Requirements Units Values PbO content (mass fraction) Pb02 content (mass fraction) Pb304 content (mass fraction) Residue in sieve over 63 um % 22,6 max. % 27,O min. % 77,4 min. % 2 max. Characteristics a Melting point Denomination Red lead (glass) Colour Orangehed Units Values “C

35、 500 Molecular mass g/mol I 685,6 Q BSI 09-2000 Page 8 EN 13086:2000 Requirements PbO content (mass fraction) Table 7 - Red lead for ceramic units Values % 22,6 max. 6 PbOz content (mass fraction) Pb304 content (mass fraction) Description I % 27,O min. % 77,4 min. Denomination Residue in sieve over

36、63 vm Characteristics a Red lead (ceramic) % 2 max. Units Values Colour Orangehed Formulae Pb304 (2Pb0 PbOn) Melting point Molecular mass “C 500 g/mol 685,6 7 Test methods 7.1 Apparent density The apparent density shall be determined in accordance with EN 23923-2. 7.2 Tamped density The tamped densi

37、ty shall be determined in accordance with EN IS0 787-1 1. 7.3 Free lead in lead oxide The free lead in lead oxide shall be determined in accordance with annex A. 7.4 Lead dioxide in red lead and litharge The lead dioxide in red lead and litharge shall be determined in accordance with annex B. 7.5 Ov

38、ersize residue The oversize residue shall be determined in accordance with annex C. 7.6 Sulfuric acid absorption index The sulfuric acid absorption index shall be determined in accordance with annex D. O BSI 09-2000 STDmBSI BS EN L308b-ENGL 2000 Lb24bb9 0872710 592 IB Page 9 EN 13086:2000 8 Ordering

39、 information The purchase order shall define the product required and shall contain the following details : a) denomination of the product (see Tables 1 to 7) ; b) number of this European Standard (EN 13086) ; c) quantity (mass) ; d) packaging and shipping conditions ; e) any other requirement agree

40、d between the purchaser and the supplier. 9 Labelling Each product shall be clearly labelled by the manufacturer, in accordance with the relevant regulations, either directly on the package or by an adhesive label on the shipping unit with the following information : a) manufacturers name or trade m

41、ark ; b) denomination of the product (see Tables 1 to 7) ; c) year and month of manufacture, and/or production reference. Q BSI 09-2000 STD.BSI BS EN L30b-ENGL 2000 Lb24669 087Z13 429 Page 10 EN 13086:2000 Annex A (no rrn at ive) Determination of free lead in lead oxides WARNING Due to the hazards i

42、nherent in a laboratory, both general and specific, this procedure shall only be carried out by fully trained personnel, or for those in the course of training, under the full supervision of trained personnel. A.l Scope This method specifies the determination of the percentage of free lead (metallic

43、 lead) in litharge and battery lead oxide (Barton and Mill). The lead monoxide content is calculated as specified in A.6.2. A.2 Principle A weighed test portion is treated with acetic acid in order to dissolve the lead monoxide. Any undissolved lead dioxide (PbOz) is reduced in ascorbic acid. A.3 Ap

44、paratus A.3.1 500 ml conical flask. A.3.2 2 O00 ml flat-bottomed flask. A.3.3 Sintered glass filters, No 4 porosity. A.3.4 Hotplate. A.3.5 A.3.6 A.3.7 Oven-capable of maintaining 105 OC f 2 OC. Balance minimum accuracy f 0,001 g. Graduated flask 1 O00 ml. A.4 Reagents A.4.1 General All reagents shal

45、l be of analytical grade. A.4.2 Deionized water, or water of equivalent quality. A.4.3 Acetic acid, glacial (p2, = 1 ,O5 g/ml). A.4.4 Acetic acid, 20 % (volume fraction). To 1 O00 ml of deionized water in a 2 O00 ml flask, add 400 ml of acetic acid, make up to the mark with water and mix. A.4.5 Asco

46、rbic acid (solution 2 %). Dissolve 20 g f 0,l g of ascorbic acid in water in a 1 O00 ml graduated flask, make up to the mark with water and mix. Q BSI 09-2000 STD-BSI BS EN 1308b-ENGL 2000 = 1b24bb9 0872912 365 ls Page 11 EN 13086:2000 A.5 Procedure A.5.1 General The procedures for the litharge and

47、for the battery oxides differ slightly as regards the mass of the test portion and the quantities of reagents used. The procedure for each is therefore detailed separately. A52 Litharge A.5.2.1 a 500 ml conical flask (A.3.1). Weigh between 50 g i: 0,l g and 100 g f 0,l g of the litharge sample and t

48、ransfer quantitatively to A.5.2.2 Add 250 ml of acetic acid 20 % (volume fraction) (A.4.4) and warm gently with shaking, until dissolution of the oxide in the sample is complete: any free lead will remain as a sediment. If the solution has a red-brown colour caused by lead dioxide (PbQ), add ascorbi

49、c acid solution (A.4.5) dropwise until the red-brown colour is discharged. A.5.2.3 discard the bulk of the supematant liquid, ensuring that none of the sediment is lost. After any red-brown colour has disappeared, allow 5 min for all particles to settle, then decant and A.5.2.4 the transfer of all the sediment. Filter the remaining contents of the flask through a pre-weighed sintered glass filter (A.3.3), ensuring A.5.2.5 Wash the sediment retained on the filter four times with cold water and finally with acetone. A.5.2.6 Trans