EN 12765-2016 en Classification of thermosetting wood adhesives for non-structural applications《非结构用途热固型木材胶粘剂分级》.pdf

《EN 12765-2016 en Classification of thermosetting wood adhesives for non-structural applications《非结构用途热固型木材胶粘剂分级》.pdf》由会员分享，可在线阅读，更多相关《EN 12765-2016 en Classification of thermosetting wood adhesives for non-structural applications《非结构用途热固型木材胶粘剂分级》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12765:2016Classification of thermosettingwood adhesives for non-structural applicationsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12765:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12765:2016. Itsupersede

2、s BS EN 12765:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/52, Adhesives.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovision

3、s of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 89031 4ICS 83.180Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under t

4、he authority of theStandards Policy and Strategy Committee on 31 August 2016.Amendments issued since publicationDate Text affectedBS EN 12765:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12765 August 2016 ICS 83.180 Supersedes EN 12765:2001English Version Classification of thermosetting

5、wood adhesives for non-structural applications Classification des colles thermodurcissables pour bois usages non structuraux Klassifizierung von duromeren Holzklebstoffen fr nichttragende Anwendungen This European Standard was approved by CEN on 8 July 2016. CEN members are bound to comply with the

6、CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management

7、Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as

8、 the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net

9、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All r

10、ights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12765:2016 EBS EN 12765:2016EN 12765:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Classification . 4 5 Test me

11、thod 5 6 Requirements . 5 Bibliography 7 BS EN 12765:2016EN 12765:2016 (E) 3 European foreword This document (EN 12765:2016) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national stan

12、dard, either by publication of an identical text or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by February 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

13、ts. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12765:2001. Compared to EN 12765:2001 the following modifications have been made: a) references to tests with thick bond lines have been removed; b) assessment is based on 20 test pieces;

14、 c) additional information on conditioning sequences added in Table 2. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar

15、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12765:2016

16、EN 12765:2016 (E) 4 Introduction European Standards giving a common classification with respect to durability classes for wood adhesives will allow considerable improvement in consumer protection in any future product liability system with regard to properties guaranteed by the adhesive manufacturer

17、. 1 Scope This European Standard classifies thermosetting resin based wood adhesives for non-structural applications into durability classes C1 to C4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments. For special applications,

18、further tests, which do not fall within the scope of this European Standard can be applicable. The adhesives specified in this European Standard are suitable for the bonding of furniture and interior structures, panelling, doors, windows, stairs etc. made of wood or derived timber products. 2 Normat

19、ive references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) a

20、pplies. EN 205:2016, Adhesives Wood adhesives for non-structural applications - Determination of tensile shear strength of lap joints EN 923, Adhesives - Terms and definitions 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 923 and the following apply

21、. 3.1 thermosetting resin thermoset monomer, polymer or copolymer, which when cured, changes into a substantially infusible and insoluble product SOURCE: EN 923:2015, 2.2.9 3.2 thermosetting wood adhesive adhesive whose main constituent is a thermosetting resin and which has been formulated for bond

22、ing wood 4 Classification An adhesive shall be classified in accordance with Table 1, which gives examples of climatic conditions and fields of application in which the bonded member is to be used. The classification shall be based on tests on thin bond-lines as defined in EN 205:2016. BS EN 12765:2

23、016EN 12765:2016 (E) 5 Table 1 Description of durability classes Durability class Examples of climatic conditions and fields of application C1 Interior, in which the moisture content of the wood does not exceed 15 % C2 Interior with occasional short-term exposure to running or condensed water and/or

24、 to occasional high humidity provided the moisture content of the wood does not exceed 18 % C3 Interior with frequent short-term exposure to running or condensed water and/or to heavy exposure to high humidity. Exterior not exposed to weather C4 Interior with frequent long-term exposure to running o

25、r condensed water. Exterior exposed to weather but with protection by an adequate surface coating 5 Test method The adhesive shall be tested in accordance with EN 205:2016, and as follows: a) bond-lines shall be tested as according to their assigned durability class (see Table 1); b) the tests shall

26、 be performed using the appropriate conditioning sequence given in Table 2; c) the individual strength values in N/mm2rounded to 0,1 N/mm2and the mean value of the 20 test pieces for each conditioning sequence shall be recorded. Results from tests in which failure occurred in the wood at values belo

27、w the specified minimum are invalid. Test pieces that are twisted, bended or showing other irregularities in form are valid if they reach the requirements; otherwise, or if visual examination shows that the adhesive was not correctly applied, the results are invalid. All results, valid or invalid, s

28、hall be reported. Explanation of the invalid values shall be reported; The standard atmosphere used as a control climate is either (20 2) C and (65 5) % relative humidity (RH), (20/65), or (23 2) C and (50 5) % relative humidity (RH), (23/50). 6 Requirements When tested in accordance with EN 205:201

29、6, the mean strength of an adhesive shall conform to the values shown in Table 2. BS EN 12765:2016EN 12765:2016 (E) 6 Table 2 Minimum values of adhesive strength for thin bond lines Conditioning sequences Adhesive strength in N/mm2Durability classes Sequence number Duration and condition C1cC2cC3 cC

30、4 c1 7 daysain standard atmosphereb 10 10 10 10 2 7 days in standard atmosphere 1 day in water at (20 5) C 7 7 7 3 7 days in standard atmosphere 3 h in water at (67 2) C 2 h in water at (20 5) C 4 4 7 days in standard atmosphere 3 h in boiling water 2 h in water at (20 5) C 4 In each conditioning se

31、quence, specimens shall change from one step to another immediately (not gradually). For the conditioning sequences 2,3 and 4 the specimens shall be tested in wet state after removing them from water. NOTE 1 The seven days in standard atmosphere are included in the conditioning time mentioned EN 205

32、:2016, 6.2. NOTE 2 A longer conditioning time between gluing and testing might be necessary as advised by the adhesive manufacturer. NOTE 3 The number used in the designation does not indicate ranking order. A given adhesive can be assigned to more than one durability class. a1 day = 24 h. b(20 2) C

33、 and (65 5) % relative humidity or (23 2) C and (50 5) % relative humidity. cAll minimum values indicated in the columns of durability classes C1 to C4 shall be reached as mean values for the classification of an adhesive (for example for C4 the conditioning sequences are 1, 2 and 4). = No test requ

34、ired. BS EN 12765:2016EN 12765:2016 (E) 7 Bibliography 1 EN 204, Classification of thermoplastic wood adhesives for non-structural applications This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-r

35、elated publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and other

36、s to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help

37、 them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF

38、 versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Cust

39、omer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally license

40、d such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any

41、manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provi

42、ded that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal c

43、ompany use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see S

44、ubscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to Brit

45、ish Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discount

46、s on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find ou

47、t more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, yo

48、u can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & Licensing