EN 12570-2000 en Industrial Valves - Method for Sizing the Operating Element《工业阀门 操作元件尺寸控制的方法》.pdf

《EN 12570-2000 en Industrial Valves - Method for Sizing the Operating Element《工业阀门 操作元件尺寸控制的方法》.pdf》由会员分享，可在线阅读，更多相关《EN 12570-2000 en Industrial Valves - Method for Sizing the Operating Element《工业阀门 操作元件尺寸控制的方法》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN L2530-ENGL 5000 W Lb24bb9 OBb5L57 OYT BRITISH STANDARD Industrial valves - Method for sizing the operating element The European Standard EN 125702000 has the status of a British Standard ICs 23.oGo.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITED BY COPYRIGHT LAW BS EN 12570:200

2、0 - STD-BSI BS EN 32570-ENGL 2000 hb24bb9 OBb5158 T8b = didon of the Engineering Amd. No. Date Sedor Committee, was published under the authority of the standards Committee and comes into effect on 15 August 2000 BS EN 126702000 Comments National foreword This British Standard is the English languag

3、e version of EN 1257Q2000. The UK participation in its preparation was entrusted by Technid Commiee PSW, Valves, to Subcommittee PSEp7I1, Valves - Basic standards, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries o

4、n the interpretation, or proposals for change, and keep the UK interests informed; - monitor related intrnatiod and European developments and promulgate them in the UK A list of organizatons represented on this subcommittee can be obtained on request to its secretary. Cross-references The British St

5、andards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by ushg the “Find” facility of the BSI Standards Electronic Catalogue. A British Stand

6、ard does not purport to include ail the necessary provisions of a contract Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, a

7、n inside front cover, the EN tite page, pages 2 to 7 and a back cover. The BSI copynght notice displayed in this document indicates when the document WaSlaStiSSUed. Q BSI 082000 I l ISBN O 580 34914 4 - STD-BSI BS EN L2570-ENGL 2000 1624669 0865159 912 EUROPEAN STANDARD EN 12570 NORME EUROPENNE EURO

8、PISCHE NORM May 2000 ICs 23.060.01 English version Industrial valves - Method for sizing the operating element Robinetterie industrielle - Mthode de dimensionnement de Iorgane de manoeuvre Industriearmaturen - Verfahren fr die Auslegung des Bettigungselementes This European Standard was approved by

9、CEN on 9 April 2000. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this Europeen Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards

10、may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three offcial versions (English, French, German). A version in any other language made by trmslation under the responsibility of a CEN member into its own language and notified to the Cen

11、tral Secretariat has the same status as tie offcial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Noway, Portugal, Spain, Sweden, Switzerland and United Kingdom

12、. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMITE EUROPEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 8-1050 Brussels 8 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12570:2000 E ST

13、DoBSI BS EN 12570-ENGL 2000 Lb24669 OBbSLbO b34 m Page 2 EN 12570:2000 Contents Page Foreword . 3 Introduction . 4 1 Scope 5 2 Normative References . 5 3 Terms and definitions 5 4 Symbols 5 5 Requirements . 6 5.1 Manual force . . 6 5.2 Sizing of the operating element 6 8 BSI 08-2000 STD*BSI BS EN L2

14、570-ENGL 2000 lb24bb7 OBb51ibL 570 D Page 3 EN 12570:2000 Foreword This European Standard has been prepared by Technical committee CENTTC 69, Industrial valves, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication o

15、f an identical text or by endorsement, at the latest by August 2000, and conflicting national standards shall be withdrawn at the latest by August 2000. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Euro

16、pean Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard has been prepared under a mandate given to CEN by the European Com

17、mission and the European Free Trade Association. This European Standard is considered to be a supporting standard to those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard. 8 B

18、SI 08-2000 STD-BSI BS EN 12570-ENGL 2000 m 1b24bb9 0865162 Li07 W Page 4 EN 12570:2000 Introduction The manual forces which a person can apply to an operating element (handwheel or lever) are basically independent of the type of the valve and depend on the person operating the valve, his position to

19、 the operating element, etc. This European Standard specifies the manual forces and the calculation method to be used in sizing the operating element for all industrial valve types. Q BSI 08-2000 STD-BSI BS EN L2570-ENGL 2000 Lb2Lihb9 0865Lb3 343 = Page 5 EN 12570:2000 I Scope This European Standard

20、 specifies the requirements for establishing the minimum size of the operating element supplied with an industrial valve having regard for the force applied by one person to operate the valve under specified working conditions. This standard applies to manual operating elements of sizes from 100 mm

21、to 1 O00 mm: - directly mounted on valves; - mounted on valve reduction gearboxes; - used for manual operation of power actuated valves. This standard does not apply to: - impactor handwheels; - T-keys; - chainwheels. 2 Normative references This European Standard incorporates by dated or undated ref

22、erence, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorpo

23、rate in it by amendments or revision. For undated references, the latest edition of the publication referred to applies (including amendments). EN 736-1, Valves - Terminology - Part I: Definition of types of valves EN 736-2, Valves - Terminology - Part 2: Definition of components of valves. EN 736-3

24、, Valves - Terminology - Part 3: Definition of terms. 3 Terms and definitions For the purposes of this European Standard the terms and definitions given in EN 736-1, EN 736-2 and EN 736-3 apply. 4 Symbols The symbols used in this standard are as follows: D L T is the diameter of the handwheel, expre

25、ssed in millimetres (mm); is the length of the lever or radius of the crank circle, expressed in millimetres (mm); is the torque, under specified conditions, to operate the valve, expressed in Newton metres (Nm); T, is the maximum torque, under specified conditions, to seat or unseat the obturator o

26、r to overcome temporary intermediate dynamic conditions, expressed in Newton metres (Nm); O BSI 08-2000 STDaBSI ES EN L2570-ENGL 2000 Lb24bbS OBb5Lb4 28T 100 125 160 200 250 250 300 300 350 400 N Page 6 EN 12570:2000 315 400 F is the operating manual force to size the manual operating element, expre

27、ssed in Newtons (N); N F, is the maximum manual force to size the manual operating element, expressed in Newtons (N). 500 600 600 700 800 800 5 Requirements 5.1 Manual force The value of the operating manual force F and the maximum manual force F, used to calculate the size of the operating element

28、according to 5.2 shall be as given in Table 1. Table 1 - Manual force I I D and L mm 400 1400 400 400 1 O00 1 O00 1 O00 1 O00 For intermediate values of D and L the applicable values of F and F, shall be calculated by linear interpolation of the tabulated values. The force F is the assumed manual fo

29、rce which one person is capable of applying to the operating element under the following conditions: - operator in standing position; - operating element at approximately waist level; - no space restrictions; - firm footing; - operating time no longer than 5 min. The force F, is the assumed manual f

30、orce which one person is capable of applying to the operating element under the same conditions as force F except that the time period is short. If other conditions apply the values of F and F, to be used shall be subject to an agreement between the manufacturer and the customer. 5.2 Sizing of the o

31、perating element The size of the operating element (see Figures 1 and 2) shall be calculated to comply with the following conditions: a) handwheel 2 000xT and 2 OOOxT, . I F Fs D shall be equal to or greater than O BSI 08-2000 - STD*BSI BS EN 12570-ENGL 2000 lb24bb9 ObClb5 116 Page 7 EN 12570:2000 b

32、) lever or crank 1 O00 xT and 1 O00 x Ts L shall be equal to or greater than F Fs The maximum torque Ts is a greater torque than T and is applied during a short time. When specified by the customer the manufacturer shall quantify this short time in terms of a percentage of the valve travel. Figure 1

33、 - Handwheel Figure 2 - Lever or handwheel with crank O BSI 08-2000 STD.BSI BS EN 12570-ENGL 2000 1b24bb OBb5Lbb 052 BS EN 12570:ZOOO ES1 389ChiswickHighRoad London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It present

34、s the UK view on standards in Europe and at the international level It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they posess the latest amendments or editions. It is the constant aim of BSI to

35、improve the quality of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fiont cover. Tel: 020 8996 9ooo. Fax

36、: O20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 0

37、20 8996 9001. Fax: O20 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, Eu

38、ropean and international standards through its Library and its Technical Help to Errporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: O20 8996 7048. Subscribing

39、 members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Amhkdmb on Tel: O20 8996 7002. Fax: 020 8996 7001. copyright Copyright subsists in all BSI publications. MI

40、 also holds the copyright, in the UK, of the publications of the international standardkation bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying

41、, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the tem may include royaity payments or a licensing agreement Details and advice can be obtained krn the Copyright Manager. Tel O20 8996 7070.