EN 12057-2015 en Natural stone products - Modular tiles - Requirements《天然石材制品 标准面砖 要求》.pdf

《EN 12057-2015 en Natural stone products - Modular tiles - Requirements《天然石材制品 标准面砖 要求》.pdf》由会员分享，可在线阅读，更多相关《EN 12057-2015 en Natural stone products - Modular tiles - Requirements《天然石材制品 标准面砖 要求》.pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 12057:2015Natural stone products Modular tiles RequirementsBS EN 12057:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12057:2015. It supersedes BS EN 12057:2004 which is withdrawn.The UK participation in its preparation was e

2、ntrusted to Technical Committee B/545, Natural stone.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Briti

3、sh Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 76927 6ICS 91.100.15Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March

4、2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12057 March 2015 ICS 91.100.15 Supersedes EN 12057:2004English Version Natural stone products - Modular tiles - Requirements Produits en pierre naturelle - Plaquettes m

5、odulaires - Exigences Natursteinprodukte - Fliesen - Anforderungen This European Standard was approved by CEN on 3 January 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar

6、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

7、other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republ

8、ic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN C

9、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12057:2015 EBS EN 1205

10、7:2015EN 12057:2015 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions .6 4 Characteristics of natural stone modular tiles .6 4.1 Geometrical characteristics 6 4.1.1 General 6 4.1.2 Dimensions .7 4.1.3 Surface finish .7 4.2 Physical and mechanical characteristi

11、cs 7 4.2.1 General 7 4.2.2 Denomination .8 4.2.3 Visual appearance .8 4.2.4 Flexural strength 9 4.2.5 Bond strength/adhesion .9 4.2.6 Water absorption at atmospheric pressure . 10 4.2.7 Reaction to fire 10 4.2.8 Water absorption by capillarity . 10 4.2.9 Apparent density and open porosity 10 4.2.10

12、Durability . 10 4.2.11 Thermal shock resistance 11 4.2.12 Water vapour permeability . 11 4.2.13 Slip resistance . 11 4.2.14 Skid resistance 11 4.2.15 Tactility 11 4.2.16 Direct airborne sound insulation 12 4.2.17 Thermal conductivity 12 4.2.18 Release of dangerous substances 12 5 Testing, assessment

13、 and sampling methods 12 5.1 Testing . 12 5.2 Sampling 12 5.2.1 General . 12 5.2.2 Principles of sampling . 13 5.2.3 Taking bulk samples 13 5.2.4 Preparing a sampling plan . 13 5.2.5 Sampling apparatus . 13 5.2.6 Sampling methods 13 5.2.7 Marking, packaging and dispatch of the samples . 15 5.2.8 Sam

14、pling report 15 6 Assessment and verification of constancy of performance - AVCP . 17 6.1 General . 17 6.2 Type Testing 17 6.2.1 General . 17 6.2.2 Test samples, testing and compliance criteria 18 6.2.3 Test reports . 19 6.2.4 Shared other party results . 19 6.2.5 Cascading determination of the prod

15、uct type results 19 6.3 Factory production control (FPC) . 21 BS EN 12057:2015EN 12057:2015 (E) 3 6.3.1 General . 21 6.3.2 Requirements . 21 6.3.3 Product specific requirements . 24 6.3.4 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity . 25 6.3.

16、5 Procedure for modifications. 26 7 Marking and packaging . 26 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation 28 ZA.1 Scope and relevant characteristics . 28 ZA.2 Procedure for attestation of conformity of natural stone m

17、odular tiles 33 ZA.2.1 System(s) of attestation of conformity 33 ZA.2.2 Declaration of performance (DoP) . 41 ZA.2.2.1 General 41 ZA.2.2.2 Content 42 ZA.2.2.3 Examples of DoP 43 ZA.2.2.3.1 Example of DoP for natural stone tiles used as internal wall and ceiling finishes . 43 ZA.2.2.3.2 Example of Do

18、P for natural stone tiles used as external wall and ceiling finishes 45 ZA.2.2.3.3 Example of DoP for natural stone tiles used as internal flooring and stair finishes 47 ZA.2.2.3.4 Example of DoP for natural stone tiles used as external flooring and stair finishes 49 ZA.3 CE marking and labelling 51

19、 Bibliography 56 BS EN 12057:2015EN 12057:2015 (E) 4 Foreword This document (EN 12057:2015) has been prepared by Technical Committee CEN/TC 246 “Natural stones”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of

20、 an identical text or by endorsement, at the latest by September 2015, and conflicting national standards shall be withdrawn at the latest by December 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

21、not be held responsible for identifying any or all such patent rights. This document supersedes EN 12057:2004. EN 12057:2015 includes the following significant technical changes with respect to EN 12057:2004: durability, resistance to thermal and moisture cycling, skid resistance, direct airborne so

22、und insulation, thermal conductivity, release of dangerous substances added to requirements; sampling at the point of delivery added to the sampling; assessment and verification of constancy of performance added; Annex ZA substantially changed. This document has been prepared under a mandate given t

23、o CEN by the European Commission and the European Free Trade Association, and supports basic requirements for construction works of Regulation (EU) No.305/2011 on Construction Products. For relationship with the Regulation, see informative Annex ZA, which is an integral part of this document. This E

24、uropean Standard is one of a series of standards for specifications of natural stone products which includes the following: EN 1467, Natural stone Rough blocks Requirements; EN 1468, Natural stone Rough slabs Requirements; EN 1469, Natural stone products Slabs for cladding Requirements; EN 12057, Na

25、tural stone products Modular tiles Requirements; EN 12058, Natural stone products Slabs for floors and stairs Requirements; EN 12059, Natural stone products Dimensional stone work Requirements. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following c

26、ountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

27、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12057:2015EN 12057:2015 (E) 5 1 Scope This European Standard specifies requirements for flat modular tiles of natural stone which are made for internal (including enclosed public transpor

28、t premises) and/or external uses as floorings, stairs and wall and ceiling finishes. This European Standard does not cover mineral aggregates and artificial agglomerated stone material and does not cover installation. 2 Normative references The following documents, in whole or in part, are normative

29、ly referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1745, Masonry and masonry products Methods for determining ther

30、mal properties EN 1925, Natural stone test methods Determination of water absorption coefficient by capillarity EN 1936, Natural stone test methods Determination of real density and apparent density, and of total and open porosity EN 12371, Natural stone test methods Determination of frost resistanc

31、e EN 12372, Natural stone test methods Determination of flexural strength under concentrated load EN 12407, Natural stone test methods Petrographic examination EN 12440, Natural stone Denomination criteria EN 12670:2001, Natural stone Terminology EN 13373, Natural stone test methods Determination of

32、 geometric characteristics on units EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13755, Natural stone test methods Determination of water absorption at atmospheric pressure EN 14066, Natural stone test

33、 methods Determination of resistance to ageing by thermal shock EN 14157, Natural stone test methods Determination of the abrasion resistance EN 16306, Natural stone test methods Determination of resistance of marble to thermal and moisture cycles EN ISO 10456, Building materials and products Hygrot

34、hermal properties Tabulated design values and procedures for determining declared and design thermal values (ISO 10456) EN ISO 12572, Hygrothermal performance of building materials and products Determination of water vapour transmission properties (ISO 12572) CEN/TS 15209, Tactile paving surface ind

35、icators produced from concrete, clay and stone CEN/TS 16165:2012, Determination of slip resistance of pedestrian surfaces Methods of evaluation NOTE Besides the European Standards for test methods mentioned in this clause, there exist further standards which can be used for scientific examinations,

36、but which are not relevant for the application in practice according to this standard. BS EN 12057:2015EN 12057:2015 (E) 6 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12670:2001 and the following apply. 3.1 modular tile flat piece of natural stone

37、 square or rectangular shapes, obtained by cutting or splitting at a nominal thickness 12 mm 3.2 dimensions of modular tiles length l, width b and thickness d, given in the stated sequence in millimetres (see Figure 1) Figure 1 Dimensions of a modular tile 3.3 calibrated tile tile which fulfil stric

38、ter tolerances for thickness, flatness and squareness 3.4 lower expected value lower expected value (EL) corresponds to the 5 %-quantile of a logarithmic normal distribution for a confidence level of 75 % 3.5 higher expected value higher expected value (EH) corresponds to the 95 %-quantile of a loga

39、rithmic normal distribution for a confidence level of 75 % 4 Characteristics of natural stone modular tiles 4.1 Geometrical characteristics 4.1.1 General All measurements shall be carried out in accordance with EN 13373 and all measured values of individual units shall fall within the required toler

40、ances. BS EN 12057:2015EN 12057:2015 (E) 7 4.1.2 Dimensions The deviations for dimensions, flatness and squareness shall be as given in Table 1. Table 1 is not valid for modular tiles having natural cleft/riven faces, for which deviations on dimensions, flatness or squareness shall be set out by the

41、 manufacturer. Table 1 Tolerances on dimensions and shape Property Tolerances on dimensions and shape Not calibrated tiles Calibrated tilesaDimensions l, b 1 mm 1 mm d 1,5 mm 0,5 mm Flatness (for honed and polished surface only)b0,15 % 0,10 % Squarenessb0,15 % 0,10 % aCalibrated tiles indicate a pro

42、duct submitted to specific mechanical finishing in order to obtain more precise dimensions; they might be suitable to be fixed by thin mortar bed or adhesives bin accordance with EN 13373 4.1.3 Surface finish 4.1.3.1 General Surface finishes shall extend uniformly to the edges of the modular tiles.

43、The surface finishing of some types of stones may typically involve the use of patching, fillers or other similar products for natural holes, faults or cracks; this is to be considered as part of the normal processing. In such cases the type of treatment, as well as the type and nature of additional

44、 materials, shall be declared. 4.1.3.2 Requirements for surfaces after surface finishing Surfaces shall be worked to achieve the specified finish and shall have a regular appearance as a result of the finishing process (e.g. making reference to samples, see 4.2.3). For definitions of surface finishe

45、s, see EN 12670. 4.2 Physical and mechanical characteristics 4.2.1 General Whenever stone processing is likely to change the characteristics of the raw material (e.g. as a consequence of the type of processing or because the use of patching, fillers or other similar products for natural holes, fault

46、s, cracks and similar), then this has to be considered when determining the characteristics requested by this document. The following characteristics shall be declared where requested by this document or with reference to the use conditions. BS EN 12057:2015EN 12057:2015 (E) 8 4.2.2 Denomination The

47、 denomination shall always be declared in accordance with EN 12440 (it means traditional name, petrological family, typical colour and place of origin). NOTE The place of origin can be given by GPS coordinates. The petrographic definition shall be determined in accordance with EN 12407. 4.2.3 Visual

48、 appearance 4.2.3.1 General The colour, veining, texture, etc. of the stone shall be identified visually, typically by a reference sample of the same stone suitable for providing a general description of visual appearance. The reference sample shall be provided by the supplier. 4.2.3.2 Reference sam

49、ple, visual inspection and acceptance criteria A reference sample shall be an adequate number of pieces of natural stone of sufficient size to indicate the general appearance of the finished work. The dimensions of individual pieces shall be at least 0,01 m2(typical values are between 0,01 m2and 0,25 m2in face area but may be more), and shall indicate the range of appearance regarding the colouring, the vein pattern, the physical structure and the surface finish. In particular the reference