EN 12039-2016 en Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules《防水软板-屋顶密封沥青板-颗粒粘附力的测定》.pdf

《EN 12039-2016 en Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules《防水软板-屋顶密封沥青板-颗粒粘附力的测定》.pdf》由会员分享，可在线阅读，更多相关《EN 12039-2016 en Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules《防水软板-屋顶密封沥青板-颗粒粘附力的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12039:2016Flexible sheets forwaterproofing Bitumensheets for roof waterproofing Determination of adhesionof granulesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12039:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation

2、of EN 12039:2016.It supersedes BS EN 12039:2000 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/546, Flexible sheets for waterproofing and watervapour control.A list of organizations represented on this committee can beobtained on request to its secre

3、tary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 91904 6ICS 91.100.50Compliance with a British Standard cannot co

4、nfer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 12039:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 120

5、39 June 2016 ICS 91.100.50 Supersedes EN 12039:1999English Version Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of adhesion of granules Feuilles souples dtanchit - Feuilles dtanchit de toiture bitumineuses - Dtermination de ladhrence des granulats Abdicht

6、ungsbahnen - Bitumenbahnen fr Dachabdichtungen - Bestimmung der Bestreuungshaftung This European Standard was approved by CEN on 20 May 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nat

7、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ve

8、rsion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,

9、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom

10、. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12039:2016

11、 EBS EN 12039:2016EN 12039:2016 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus . 4 6 Preparation of test samples and test specimens . 5 6.1 Sampling . 5 6.2 Sampling and preparation of test specimens 5 7 Procedure.

12、 5 8 Expression of results 5 9 Accuracy . 6 10 Test report . 6 Annex A (normative) Brush model and area brushed 7 Annex B (normative) Determination of the initial mass of granules 8 B.1 Apparatus and materials 8 B.2 Specimens 8 B.3 Procedure. 8 B.4 Calculation and expression of results 8 BS EN 12039

13、:2016EN 12039:2016 (E) 3 European foreword This document (EN 12039:2016) has been prepared by Technical Committee CEN/TC 254 “Flexible sheets for waterproofing”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of

14、 an identical text or by endorsement, at the latest by December 2016, and conflicting national standards shall be withdrawn at the latest by December 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held resp

15、onsible for identifying any or all such patent rights. This document supersedes EN 12039:1999. List of main changes since this new edition: a) editorial changes; b) replacement of ISO 565 in B.1.2. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the followi

16、ng countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

17、way, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12039:2016EN 12039:2016 (E) 4 1 Scope This European Standard applies to the apparatus and the test procedure used for the determination of the adhesion of granules to factory made bit

18、uminous sheets for roofing. It can also be used in other areas where it is relevant. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For u

19、ndated references, the latest edition of the referenced document (including any amendments) applies. EN 13416:2001, Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling ISO 3310-1, Test sieves Technical requirements and testing Part 1: Te

20、st sieves of metal wire cloth 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 surface upper side of the sheet, as used in situ; which is usually the inside of the roll 3.2 granule particle which does not pass a sieve as defined in B.1.2 4 Pri

21、nciple The method determines the adhesion of granules during a brushing test under specified conditions. The mass of brushed-off granules is compared to the original mass of granules on a test specimen cut off from the same roll. 5 Apparatus 5.1 Brushing machine, working automatically to perform out

22、ward and return cyclic linear movements between a replaceable brush applied with a force of (21,5 0,5) N on the surface of the test specimen, and the test specimen itself. The constant amplitude A of the relative movement of the axis of the replaceable brush is (200 20) mm, and the average displacem

23、ent speed is such that 50 cycles are achieved within (55 5) s. The brushing machine shall include suitable clamps, at least 50 mm wide, to restrain the ends of the specimen. 5.2 Replaceable brush, consisting of a block of a suitable material in which 22 holes are drilled as indicated in Figure A.1,

24、with a 4 mm diameter. From each hole, 22 polyamide 66 yarns, diameter 0,80 mm project (16 2) mm. The effective area of the replaceable brush, when loaded, is 80 mm 25 mm. The effective brushed area B, as shown in Figure A.2, is (A + 80) 25 mm2. A single replaceable brush shall be used for a maximum

25、of 100 tests of fewer if yarns are projecting less than 13 mm from a hole. 5.3 Balance, accurate to the nearest 0,01 g. BS EN 12039:2016EN 12039:2016 (E) 5 5.4 Machine, to cut or die-cut test specimens with a width of (50 1) mm in the desired length. 5.5 Room for conditioning, temperature (23 2) C a

26、nd (50 20) % relative humidity. 5.6 Household vacuum cleaner, 500 W, sucking air through an accessory 50 mm wide. 6 Preparation of test samples and test specimens 6.1 Sampling Sampling in accordance with EN 13416:2001. 6.2 Sampling and preparation of test specimens Test specimens shall be cut or die

27、-cut in the dimension (50 1) mm wide, length minimum 285 mm, from the samples in the length direction of the sheet. Condition five test specimens for (24 0,5) h in the climate room at (23 2) C. Suck the loose granules from the test specimens carefully moving the vacuum cleaner accessory over their s

28、urfaces. Determine the mass M1iof each test specimen to the nearest 0,01 g. 7 Procedure The mass of brushed-off granules is compared to the initial mass of granules of the test specimens cut from the same roll and in the same position on the sheet with respect either to its axis or right side or lef

29、t side. Determine the initial mass of granules in accordance with Annex B. Secure the test specimen onto the brushing machine using the clamps, and place the loaded replaceable brush on the test specimen, the length of the replaceable brush being in the length direction of the specimen (see Figure A

30、.2). Perform 50 cycles and remove the test specimen from the brushing machine. Repeat the procedure for each test specimen. Suck the loose granules from the test specimens moving the vacuum cleaner accessory over their surfaces. Determine the mass M2iof each test specimen to within 0,01 g. 8 Express

31、ion of results Determine the adhesion of granules (Mi), expressed as percentage of relative difference between the two masses of each test specimen using Formula (1): 100o2i1ii=GBMMM (1) where Gois the initial mass of granules per 1 m2in the same third of the sample where the specimens were cut in a

32、ccordance with EN 13416:2001, in gram/square metre (g/m2), as determined in Annex B; M1iis the mass of the test specimen before brushing, in gram (g); M2iis the mass of the test specimen after brushing, in gram (g); BS EN 12039:2016EN 12039:2016 (E) 6 B is the area effectively brushed, in square met

33、re (m2). 9 Accuracy The precision of the method is not specified. NOTE No report on interlaboratory tests on repeatability, r, or on reproducibility, R, is available. The accuracy will be specified when sufficient interlaboratory data are available. 10 Test report The test report shall include at le

34、ast the following information: a) all details necessary to identify the product tested; b) a reference to this European Standard and any deviation from it; c) information on sampling and details on preparation of test specimens in accordance with Clause 6; d) information on the test procedure in acc

35、ordance with Clause 7; e) the test results in accordance with Clause 8; f) date of the test. BS EN 12039:2016EN 12039:2016 (E) 7 Annex A (normative) Brush model and area brushed Dimensions in millimetres Key 1 22 holes 4 2 22 wires 0,8 Figure A.1 Brush model Dimensions in millimetres Key 1 support 2

36、 fixing clamp for specimen (example) 3 test specimen 4 replaceable brush Figure A.2 Area brushed BS EN 12039:2016EN 12039:2016 (E) 8 Annex B (normative) Determination of the initial mass of granules B.1 Apparatus and materials B.1.1 Hot extraction apparatus, usually of a SOXHLET type. B.1.2 315 m si

37、eve in accordance with ISO 3310-1. B.1.3 Solvent, e.g. toluene, trichloroethylene or dichloromethane, according to national safety regulations. B.1.4 Balance see 5.3. B.2 Specimens Cut the specimens from the roll(s) which was (were) sampled in preparation for the granule adhesion test. Exclude the f

38、irst and the last metre in the length direction of the roll, and 100 mm nearest to the edge in the width direction of the roll. Divide the roll equally into three parts in the length direction. From each third, cut two specimens of (100 1) mm (100 1) mm to the nearest 1 mm (total area of each specim

39、en 0,01 m2) or alternatively 70 mm 50 mm (total area of each specimen 0,0035 m2). Each pair of specimens will be representative of the initial mass of granules found in the thirds of roll used for the adhesion test. B.3 Procedure B.3.1 The area Siof the specimen shall be calculated in m2. B.3.2 The

40、specimen shall be placed in the extractor with the solvent adjusted as necessary. B.3.3 Soluble components shall be separated by hot extraction, until the solvent in the hot extraction apparatus becomes colourless (usually 1 h to 2 h). B.3.4 The specimen shall be taken out of the extractor, dried at

41、 (105 2) C for at least 2 h. B.3.5 The granules shall be separated from other components using sieve (B.1.2). B.3.6 The mass of the granules Nishall be determined to the nearest 0,01 g. The procedure shall be repeated on each specimen. B.4 Calculation and expression of results B.4.1 Calculate the ma

42、ss per unit area of granules (Gi), expressed in g/m2, of each specimen using Formula (B.1): iiiSNG = (B.1) BS EN 12039:2016EN 12039:2016 (E) 9 where Niis the mass of the granules relative to one specimen, in gram (g); Siis the area of the specimen, in square metre (m2). B.4.2 Calculate the mean (Go)

43、, expressed in g/m2, of the individual values Giof the specimens cut from the same third of the roll. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and servi

44、ces.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and e

45、xpertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on s

46、tandardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including B

47、ritish and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI public

48、ationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial p

49、ublication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal o