EN 12004-2007 1250 Adhesives for tiles - Requirements evaluation of conformity classification and designation (Incorporates Amendment A1 2012)《瓷砖用粘合剂 要求 一致性评估 分类和标识》.pdf

《EN 12004-2007 1250 Adhesives for tiles - Requirements evaluation of conformity classification and designation (Incorporates Amendment A1 2012)《瓷砖用粘合剂 要求 一致性评估 分类和标识》.pdf》由会员分享，可在线阅读，更多相关《EN 12004-2007 1250 Adhesives for tiles - Requirements evaluation of conformity classification and designation (Incorporates Amendment A1 2012)《瓷砖用粘合剂 要求 一致性评估 分类和标识》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 12004:2007Adhesives for tiles Requirements, evaluation of conformity, classification and designationThe European Standard EN 12004:2007 has the status of aBritish StandardICS 83.180; 91.100.10 BS EN +A1:2012Copyright European Committee for Standardization Provided by IHS under

2、license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 12004:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0580 57392 7National forewordThis British Sta

3、ndard is the UK implementation of EN 12004:2007. It supersedes BS EN 12004:2001 whichiswithdrawn. The UK participation in its preparation was entrusted to Technical Committee B/539, Ceramic tiles and other rigid tiling.A list of organizations represented on this committee can be obtained on request

4、to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsBS EN 1

5、2004:2007+A1:2012ISBN 978 0 580 74097 5Amendments/corrigenda issued since publicationDate Comments30 September 2012 Implementation of CEN amendment A1:2012This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 The British Standards

6、Institution 2012. Published by BSI Standards Limited 2012National forewordThis British Standard is the UK implementation of EN 12004:2007+A1:2012. It supersedes BS EN 12004:2007 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags

7、indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by .Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,

8、-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12004:2007+A1 June 2012 ICS 83.180; 91.100.10 Supersedes EN 12004:2007English Version Adhesives for tiles - Requirements, evaluation of conformity, classification and designation Colles carrelage - Exigences, valuation de la conformit, classifi

9、cation et dsignation Mrtel und Klebstoffe fr Fliesen und Platten - Anforderungen, Konformittsbewertung, Klassifizierung und Bezeichnung This European Standard was approved by CEN on 4 February 2007 and includes Amendment 1 approved by CEN on 13 May 2012. CEN members are bound to comply with the CEN/

10、CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Cent

11、re or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

12、 official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania

13、, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means rese

14、rved worldwide for CEN national Members. Ref. No. EN 12004:2007+A1:2012: EBS EN 12004:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 BSI 2007ISBN 978 0580 57392 7National forewordThis British Standard is the UK implement

15、ation of EN 12004:2007. It supersedes BS EN 12004:2001 whichiswithdrawn. The UK participation in its preparation was entrusted to Technical Committee B/539, Ceramic tiles and other rigid tiling.A list of organizations represented on this committee can be obtained on request to its secretary.This pub

16、lication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsCopyright European Committee for

17、 Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 12004:2007+A1:2012 (E) 2 Contents Page Foreword 3Introduction . 41 Scope 52 Normative references 53 Terms and definitions . 64 Requirements . 94.1 Cementitious

18、 adhesives (C) 94.2 Dispersion Adhesives (D) . 94.3 Reaction resin adhesives (R) 104.4 Reaction to fire . 114.5 Release of dangerous substances . 125 Evaluation of conformity . 135.1 Principle 135.2 Conditioning of the test specimen . 135.3 Initial type testing 135.4 Factory Production Control 145.5

19、 Registration, traceability and non-conforming materials 175.6 !Initial inspection of factory and of FPC . 175.7 Continuous surveillance of FPC“ . 186 Classification and designation . 187 Marking and labelling 20Annex A !(normative)“ Failure patterns 21Annex ZA (informative) Clauses of this European

20、 Standard addressing the provisions of the EU Construction Products Directive 22Bibliography 31BS EN 12004:2007+A1:2012EN 12004:2007+A1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license

21、 from IHS-,-,-EN 12004:2007+A1:2012 (E) 3 Foreword This document (EN 12004:2007+A1:2012) has been prepared by Technical Committee CEN/TC 67 “Ceramic tiles”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an i

22、dentical text or by endorsement, at the latest by December 2012, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be he

23、ld responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2012-05-13. This document supersedes !EN 12004:2007“. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prep

24、ared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Inte

25、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

26、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 12004:2007+A1:2012EN 12004:2007+A1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reprod

27、uction or networking permitted without license from IHS-,-,-EN 12004:2007+A1:2012 (E) 4 Introduction It is essential that the characteristics of the construction products defined in this standard consider that the normal stresses due to the works for which they are intended, assembled or installed,

28、can be properly accommodated. Some special characteristics will take into account the type of substrate and that the adhesives should resist the degrading actions of climate, etc. Many properties of adhesives for tiling are mainly determined by the type of binders used. Different types of tile adhes

29、ives are defined according to the chemical nature of their binders. The different types have specific characteristics in terms of their application properties and final performance. The relationship between characteristics and the working conditions (dry or humid conditions, hot climate, fast settin

30、g, etc.) is not given in this standard. The manufacturer should give information about the use of the product and the correct conditions of use. The specifier should evaluate the state of the job site (mechanical and thermal influences) and choose the appropriate product considering all the possible

31、 risks. BS EN 12004:2007+A1:2012EN 12004:2007+A1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 12004:2007+A1:2012 (E) 5 1 Scope !This European Standard is applicable

32、 to ceramic tile cementitious adhesives, dispersion adhesives and reaction resin adhesives for internal and external tile installations on walls and floors.“ This standard gives the terminology concerning the products, working methods, application properties, etc, for ceramic tile adhesives. This Eu

33、ropean Standard specifies the values of performance requirements for ceramic tile adhesives (cementitious, dispersion and reaction resin adhesives). This European Standard does not provide criteria or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives may a

34、lso be used for other types of tiles (natural and agglomerated stones, etc.), if they do not adversely affect these materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For u

35、ndated references, the latest edition of the referenced document (including any amendments) applies. EN 1308, Adhesives for tiles Determination of slip EN 1324:2007, Adhesives for tiles Determination of shear adhesion strength of dispersion adhesives EN 1346, Adhesives for tiles Determination of ope

36、n time EN 1347, Adhesives for tiles Determination of wetting capability EN 1348:2007, Adhesives for tiles Determination of tensile adhesion strength for cementitious adhesives EN 12002, Adhesives for tiles Determination of transverse deformation for cementitious adhesives and grouts !EN 12003:2008“,

37、 Adhesives for tiles Determination of shear adhesion strength of reaction resin adhesives EN 12808-1, !Grouts for tiles Part 1: Determination of chemical resistance of reaction resin mortars“ !EN 13238, Reaction to fire tests for building products Conditioning procedures and general rules for select

38、ion of substrates“ EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests !EN 13823, Reaction to fire tests for building products Building products excluding floorings exposed to the thermal attack by a single burn

39、ing item EN 14411, Ceramic tiles Definitions, classification, characteristics and marking EN ISO 11925-2, Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test (ISO 11925-2)“ BS EN 12004:2007+A1:2012EN 12004:2007+A1:2012 (E)Copyrigh

40、t European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 12004:2007+A1:2012 (E) 6 3 Terms and definitions For the purpose of this document, the following terms and definitions apply. 3.1 Gener

41、al 3.1.1 thin bed method method used for installing tiles onto a plane surface with an adhesive NOTE The adhesive is usually applied with a trowel to obtain a layer and then combed with a notched trowel to achieve the right thickness and planarity 3.1.2 fixing surface plane rigid surface upon which

42、the tile is fixed 3.1.3 wall and floor tiles tiles made out of ceramic or natural and agglomerated stones 3.2 Products 3.2.1 cementitious adhesive mixture of hydraulic binding agents, aggregates, and organic additives NOTE 1 The adhesives are mixed with water or liquid admix just before use. NOTE 2

43、Cementitious adhesives are designated as type C. 3.2.2 dispersion adhesive mixture of organic binding agent(s) in the form of an aqueous polymer dispersion, organic additives and mineral fillers NOTE 1 The mixture is ready for use NOTE 2 Dispersion adhesives are designated as type D. 3.2.3 reaction

44、resin adhesive mixture of synthetic resin, mineral fillers and organic additives in which hardening occurs by chemical reaction NOTE 1 They are available in one or more component forms NOTE 2 reaction resin adhesive are designated as type R 3.3 Tools and working methods 3.3.1 notched trowel toothed

45、tool, which makes it possible to apply the adhesive as a series of ribs of a uniform thickness onto the fixing surface and/or the reverse face of the tile BS EN 12004:2007+A1:2012EN 12004:2007+A1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for R

46、esaleNo reproduction or networking permitted without license from IHS-,-,-EN 12004:2007+A1:2012 (E) 7 3.3.2 application to one surface only, Notched trowel or Floating method adhesive applied only to the fixing surface, usually with a trowel to obtain a uniform layer and then combed with a notched t

47、rowel NOTE The tiles are then fixed before a film forms on the surface of the adhesive 3.3.3 application to both surfaces, Floating and buttering method adhesive applied to the fixing surface and to the reverse of the tiles NOTE The combined layer of adhesive should not exceed the maximum recommende

48、d thickness. The tiles are then fixed before a film forms on the surface of the adhesive 3.4 Application properties 3.4.1 shelf life time of storage under stated conditions during which an adhesive is expected to maintain its working properties 3.4.2 maturing time interval between the time when the cementitious adhesive is mixed and the time when it is ready for use 3.4.3 pot-life maxim