EN 1071-13-2010 en Advanced technical ceramics - Methods of test for ceramic coatings - Part 13 Determination of wear rate by the pin-on-disk method《高级工程陶瓷 陶瓷覆层试验方法 第13部分 磨损率销盘式试验》.pdf
《EN 1071-13-2010 en Advanced technical ceramics - Methods of test for ceramic coatings - Part 13 Determination of wear rate by the pin-on-disk method《高级工程陶瓷 陶瓷覆层试验方法 第13部分 磨损率销盘式试验》.pdf》由会员分享,可在线阅读,更多相关《EN 1071-13-2010 en Advanced technical ceramics - Methods of test for ceramic coatings - Part 13 Determination of wear rate by the pin-on-disk method《高级工程陶瓷 陶瓷覆层试验方法 第13部分 磨损率销盘式试验》.pdf(26页珍藏版)》请在麦多课文档分享上搜索。
1、BS EN 1071-13:2010ICS 81.060.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAdvanced technical ceramics Methods of test for ceramic coatingsPart 13: Determination of wear rate by the pin-on-disk methodThis British Standardwas published under theauthority of t
2、he StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 60126 2Amendments/corrigenda issued since publicationDate CommentsBS EN 1071-13:2010National forewordThis British Standard is the UK implementation of EN 1071-13:2010.The UK participation in its preparation was entrusted
3、to TechnicalCommittee RPI/13, Advanced technical ceramics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Complia
4、nce with a British Standard cannot confer immunityfrom legal obligations.BS EN 1071-13:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1071-13 March 2010 ICS 81.060.30 English Version Advanced technical ceramics - Methods of test for ceramic coatings - Part 13: Determination of wear rate by
5、 the pin-on-disk method Cramiques techniques avances - Mthodes dessai pour revtements cramiques - Partie 13 : Dtermination du taux dusure selon la mthode pin-on-disk Hochleistungskeramik - Verfahren zur Prfung keramischer Schichten - Teil 13: Bestimmung der Verschleirate mittels Stift-Scheibe-Prfung
6、 This European Standard was approved by CEN on 30 January 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical re
7、ferences concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN memb
8、er into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland
9、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17,
10、B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1071-13:2010: EBS EN 1071-13:2010EN 1071-13:2010 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Signifi
11、cance and use .65 Principle 66 Apparatus .66.1 Pin-on-disk method testing apparatus 66.2 Test apparatus design requirements .76.3 Instruments for determining the volume loss 86.4 Operating environment .87 Preparation of test pieces .87.1 Substrate material and preparation .87.2 Coating deposition 97
12、.3 Post-coating preparation 97.4 Cleaning . 108 Testing procedure. 108.1 Preliminary setup 108.2 Producing the wear track and scar . 118.3 Evaluation of wear and measurement of wear scars 118.4 Calculation of test results 149 Repeatability and limits 1510 Report 16Annex A (informative) Methods for t
13、he determination of coating properties likely to be relevant to coating performance in a pin-on-disk wear test 18A.1 Relevant properties 18A.2 Phase composition and preferred orientation. 18A.3 Residual stress . 18A.4 Hardness 18Annex B (informative) Determination of volume loss from the pin using p
14、rofilometry 19Annex C (informative) Determination of wear of coated disk by ball crater technique 20Bibliography . 23BS EN 1071-13:2010EN 1071-13:2010 (E) 3 Foreword This document (EN 1071-13:2010) has been prepared by Technical Committee CEN/TC 184 “Advanced technical ceramics”, the secretariat of
15、which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2010, and conflicting national standards shall be withdrawn at the latest by September 2010. Attention is drawn to t
16、he possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 1071, Advanced technical ceramics Methods of test for ceramic coatings, consists of the following 13 parts
17、: Part1: Determination of coating thickness by contact probe filometer Part 2: Determination of coating thickness by the crater grinding method Part 3: Determination of adhesion and other mechanical failure modes by a scratch test Part 4: Determination of chemical composition by electron probe micro
18、analysis (EPMA) Part 5: Determination of porosity (withdrawn) Part 6: Determination of the abrasion resistance of coatings by a micro-abrasion wear test Part 7: Determination of hardness and Youngs modulus by instrumented indentation (withdrawn) Part 8: Rockwell indentation test for evaluation of ad
19、hesion Part 9: Determination of fracture strain Part 10: Determination of coating thickness by cross sectioning Part 11: Determination of internal stress by the Stoney formula Part 12: Reciprocating wear test Part 13: Determination of wear rate by the pin-on-disk method Part 7 was a Technical Specif
20、ication and Parts 8 to 11 are Technical Specifications. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Fin
21、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 1071-13:2010EN 1071-13:2010 (E) 4 Introduction The determination of the
22、wear resistance of thin ceramic coatings used in sliding contacts is of high importance in several industrial fields such as stamping, moulding, blanking and in many situations where two mechanical components slide on each other. This part of EN 1071 describes a method for evaluating the wear of cer
23、amic coatings by use of a test in which a flat or spherically ended pin is brought, under load, into contact with a flat disk and the two are set in relative motion such that the pin describes a circular path on the flat surface of the disk. Depending on the information required, either the disk or
24、pin or both may be coated with the material under test, with the other member of the couple being selected for its relevance to the tribosystem under evaluation. Wear is determined by weight loss, by profilometry, by linear measurement or by a combination of these. Testing may be carried out under d
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN1071132010ENADVANCEDTECHNICALCERAMICSMETHODSOFTESTFORCERAMICCOATINGSPART13DETERMINATIONOFWEARRATEBYTHEPINONDISKMETHOD
链接地址:http://www.mydoc123.com/p-705512.html