EN 1053-1995 en Plastics Piping Systems - Thermoplastics Piping Systems for Non-Pressure Applications - Test Method for Watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 防水性的检验方法》.pdf

《EN 1053-1995 en Plastics Piping Systems - Thermoplastics Piping Systems for Non-Pressure Applications - Test Method for Watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 防水性的检验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 1053-1995 en Plastics Piping Systems - Thermoplastics Piping Systems for Non-Pressure Applications - Test Method for Watertightness《塑料管道系统 无压力情况下使用的热塑管道系统 防水性的检验方法》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、CEN ENxL0.53 95 PI 3404589 OL372L4 4LT M BRITISH STANDARD Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness The European Standard EN 1053 : 1995 has the status of a British Standard ICs 23.040.20 NO COPYING WITHOUT BSI PERMISSION E

2、XCEPT AS PERMITTED BY COPYRIGHT LAW ,LLmi?Tr5-J -2 ,L, . !ALdmsr%Emm _ BS EN LO53 : 1996 BS 2782 : Part 11 : Nethod 1112B : 1996 CEN EN*L053 95 I 3404589 OL372L5 356 = Amd.No. BS EN 1053 : 1996 Date Text affected Committees responsible for this British Standard The preparation of this British Standa

3、rd was entrusted by Technical Committee PRY61, Plastics piping systems and components, upon which the following bodies were represented British Gas plc British Phtics Federation British Plumbing Fttings Manufacturers Association British Valve and Actuator Manufacturers Association Department of the

4、Environment (British Board of Agrment) Department of the Environment (Building Research Establishment) Department of the Environment (Property and Buildings Directorate) Department of Ransport Electricity Association Federation of Civil Engineering Contsactors Health and Safety Executive Institute o

5、f Building Control Institute of Materials Institution of Civil Engineers Institution of Gas Engineers Institution of Water and Environmental Management National Association of Plumbing, Heating and Mechanical Services Contractors Fipeiine Industries Guild Plastics Land Drajnage Manufacturers Associa

6、tion Society of British Gas Industries Society of British Water Industries Water Companies Association Water Services Association of England and Wales The following bodies were also represented in the drafting of the standard, through subcommittees and panels: This British Standard, having been prep

7、ared under the direction of the Sector Board for Materiais and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 August 1996 O BSI 1996 Engineering Equipment and Materials Users Association ERA Technology LM. WRA Technology Ltd. The following BSI referen

8、ces relate to the work on this standard Committee reference PRi61 Draft for comment 9U5.2897 DC ISBN O 680 25545 X CEN ENxL053 95 3404589 OL332Lb 292 E BS EN 1053 : 1996 Contents Committees responsible National foreword page Inside front cover ii Foreword Method 1 Scope 2 principle 3 APP- 4 Test pie

9、ces 2 6 Procedure 3 6 Testrewrt 3 Figure 1 Qpicalarrangement 4 i CEN EN81053 95 3404589 0137217 129 BS EN 1053 : 1996 National foreword This British Standard has been prepared by Technical Committee PRY61 and is the English language version of EN 1053 : 1995 Plastics piping systems - Thermoplastics

10、piping systems for non-pressure applications - Test method for watertightness, published by the European Committee for Standardization (CEN). It is incorporated into BS 2782 Methods of testing plastics: Part 11: Thermoplastics pipes, fittings and valves, as Method 1112B : 1996 for association with r

11、elated test methods for plastics materiais and plastics piping components. This test method has been prepared for reference by other standards under preparation by CEN for specification of plastics piping systems and components. It has been implemented to enable experience of the Method to be gained

12、 and for use for other fresh applications. It is also for use for the revision or amendment of other national standards as practicable, but it should not be presumed to apply to any existing standard or specification which contains or makes reference to a Merent test method until that standardspecif

13、ication has been mended or revised to make reference to this Method. This Method supersedes BS 2782 : Part 11 : Method 111% : 1989, which becomes obsolescent except for supporting references thereto in BS 4576 : Part 1 : 1989, BS 4660 : 1989 and BS 5255 : 1989. The principal technical differences be

14、tween EN 1053 : 1995 and BS 2782 : Part 11 : Method 1112A : 1989 are as follows. Parameter EN 1053 : 1995 Ambient temperature during test piece assembly and testmg (23 It 5) “C Anguiax deflection applied to the joint under test Yes, if deflection is possible, to maximum declared for the joint by its

15、 manufacturer Period for raisiig the pressure to the test pressure of 2 0,5 bar Period for which a test pressure of 2 0,5 bar is maintained smoothiy over not greater than 15 min at least 15 min Inspection for and report Yes of any change in appearance (other than 1-e) BS 2782 : Part 11 : Method 1112

16、A: 1989 15 “C to 35 “C Not specifically required, unless specified by the product specification Not specified not less than 60 s Not called for Warning note. This British Standard, which implements EN 1053 : 1995, does not necessarily detaii all the precautions necessary to meet the requirements of

17、the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate dety precautions and the test method should be operated only by trained personnel Compliance with a British Standard does not of itself confer immunity from legal obligations. ii O BSI 1996 CEN ENxL053 95 340458

18、9 0337238 065 = EUROPEAN sTANDAEI;D EN 1053 NORME EUR0PEE?E EXJROP- NOFUM October 1995 ICs 23.040.20 Descriptors: Sanitation, water removal, sewage, buildings, interior, plastic tubes, thermoplastic resins, leak tests, water-tightness verification English version Plastics piping systems - Thermoplas

19、tics piping systems for non-pressure applications - method for watertghtn Systemes de c.anak - test parametem, except those common to all plastics, are omitted; - no diameter hit is included; - no materialdependent requirements are given; - editorial changes have been introduced; - the method has be

20、en extended to cover quick testing of fabricated products made nom more than one piece. The materiaidependent test parametem anaor performance requirements are incorporated in the system standard(s) concerned. This standard is one of a series of standards on test methods which support system standar

21、ds for plastics piping systems and ducting systems. O BSI 1996 CEN EN81053 95 m 3404589 0137220 713 m 1 Scope This standard specifies a test method for watertightness of: a) joints of thermoplastics piping systems for non-pressure applications; b) thermoplastics fabricated products made from more th

22、an one piece for non-pressure applications. 2 Principle A test assembly comprising either a fabricated product or an assembly of pipes and/or fittings is subjected to a given internai hydrostatic pressure for a given period during which the leaktightness of the fabricated product or the joint is ver

23、ified by inspection. NOTE. It is assumed that the following test parameters are set by the standard making reference to this standard a) the sampling procedure (see 4.1); b) the number of test pieces (see 4.2). 3 Apparatus 3.1 End-sealing devices, having a size and using a sealing method both approp

24、riate to the type of joint under test. The devices shall be restsallied in a manner that does not exert longitudinal forces on the joint assembly and that prevents the devices or the assembly under test from separating under pressure. The weight of the devices shall not be allowed to influence the a

25、ngular deflection to be applied (see 6.2). 3.2 Hgdmstatic pressure source, connected to one end of at least one end-sealing device, capable of applying the requjred pressure gradually and evenly in accordance with 6.4 and then of keeping it constant to +2 -1 (see clause 6). 3.3 Bleed valve, capable

26、of venting air when hydrostatic pressure is applied to the test piece. 3.4 Pressure measuring o!mice, Capable of checking conformity to the required test pressure (see 3.2 and clause 6). % for the duration of the test required 4 lst pieces 4.1 Preparation The test piece shall comprise either a fabri

27、cated fitting or an assembly of (a) pipe section) (with or without sockets) and/or fitting) including at least one joint of the type under test (see figure 1). To assist air removal, the test piece may be inclined by up to 12“. The assembly of the joint) shall be carried out in accordance with the m

28、anufacturers instructions. The assembly shall comprise the combination of the smallest available spigot end and the largest available socket or socket groove diameter within the applicable tolerance(s) and obtained by sampling in accordance with the referring standard. The relevant chneters of the s

29、elected spigot(s) and socket) shall be measured and recorded Page 3 EN 1053 : 1995 4.2 Number The number of test pieces shall be as specied in the referring standard. 6 Procedure 6.1 Carry out the following procedure at an ambient temperature of (23 5) “C using cold tap water without permitting any

30、condensation on the surface of the test piece. 6.2 Mount the test piece in the apparatus. If the joint to be tested permits angular deflection, arrange the test assembly so that the joint(s) under test is (are) subject to the (their) maximum angular deflection, as declared for the joint by the manuf

31、acturer, for the axes of the components thus joined. 6.3 When testing in accordance with 6.4 and 6.6, monitor the test piece for and record any evidence of leakage. 6.4 Introduce water into the test piece, while bleeding off ali air, and apply the hydrostatic pressure as follows: a) accelerated proc

32、edure for fabricated products: unless otherwise specified in the referring standard, apply an hydrostatic pressure of 0,5 bar (50 kPa) and maintain it for at least 1 min. b) assemblies of pipes and/or fittings which are not fabricated: raise the hydrostatic pressure smoothly over a period of not gre

33、ater than 15 min to 0,5 bar (50 kPa) and maintain that pressure for at least 15 min 6.6 Depressurize, drain and dismantle the test piece. Inspect for and record any changes in the appearance of the components tested. 6 Test report The test report shall include the following information: a) a referen

34、ce to this standard and to the referring standard; b) the identification of the components (e.g. fitting(s), pipe), sea) comprising the joint(s) under test and their respective diameters, in millimetres (see 4.1); c) the ambient temperature (see 6.1), in degrees Celsius; d) the test pressure, in bar

35、s; e) the length of time under pressure, in minutes; f) if applicable, the angle of deflection applied to the joint (see 6.2); g) a statement, that the joint did not leak or, if any, a report of signs of leakage or rupture, their position(s) and the pressure at which they occurred; h) any changes in

36、 the appearance of the components of the test piece(s) during the test, or immediately afterwardq i) any factors which may have affected the results, for example, such as any incidents or any operating details not specified in this standard j) the dak of the test. O BSI 19% CEN EN*3053 95 m 3404589

37、O337223 b5T m Page 4 EN 1053 : 1995 Dimensions in metres Air outlet Water inlet Sealing plug with water inlet, air outlet and end restraint Water outlet Sealing plug with water outlet and end restraint (see 3.1) Direction of movement for anguiar deflection, if applicable (see 5.2) Loose bushes to al

38、low all sizes of pipes to be accommodated on the same test fixture bed points Fixed component Figure 1. pical arrangement O BSI 1996 CEN ENa1053 95 = 3404589 0137222 596 BS EN 1053 : 1996 BS 2782 : Part 11 : Method 1112B : 1996 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institu

39、tion BSI is the independent national body responsible for preparing British standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions

40、 of a contract. Users of British Standasds are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the Fax: O181 996 7400. BSI offers members an individual updating service called P

41、LUS which ensures that subscribers automatidy receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addresed to Customer Services, Sales Department at Chiswick Tel O181 996 7000; Fax: O181 996 7001. In response to or

42、ders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on nationai, European and international standards through its Libr

43、ary, the Standardline Database, the BSI Information Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick Tel O181 996 7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive subs

44、tantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel O181 996 7002; Fax: O181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of

45、 the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission

46、 from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the tem may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL.