EN 10296-2-2005 en Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2 Stainless steel (Incorporating corrigendum F.pdf

《EN 10296-2-2005 en Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2 Stainless steel (Incorporating corrigendum F.pdf》由会员分享，可在线阅读，更多相关《EN 10296-2-2005 en Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2 Stainless steel (Incorporating corrigendum F.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 10296-2:2005Incorporating corrigenda nos. 1 and 2Welded circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 2: Stainless steelThe European Standard EN 10296-2:2005 has the status of a British StandardICS 77.140.75g49g50g3g38g5

2、0g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 10296-2:2005This British Standard was published under the authority of the Standards Policy and Strategy Co

3、mmittee on 20 December 2005 BSI 2007ISBN 978 0 580 59328 4National forewordThis British Standard is the UK implementation of EN 10296-2:2005, incorporating corrigendum February 2007. It supersedes BS 6323-8:1982 which is withdrawn. Together with BS EN 10296-1:2003, BS EN 10297-1:2003, BS EN 10305-1:

4、2002, BS EN 10305-2:2002, BS EN 10305-3:2002, BS EN 10305-4:2003, BS EN 10305-5:2003 and BS EN 10305-6:2005 it supersedes BS 6323-1:1982 which is withdrawn.The start and finish of text introduced or altered by corrigendum is indicated in the text by tags . Text altered by CEN corrigendum February 20

5、07 is indicated in the text by .The UK participation in its preparation was entrusted to Technical Committee ISE/8, Steel pipes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions

6、of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date Comments17061 Corrigendum No. 130 April 2007 See national foreword.17259 Corrigendum No. 231 August 2007

7、 Revision to supersession details.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10296-2December 2005ICS 77.140.75 Incorporating corrigendum February 2007English VersionWelded circular steel tubes for mechanical and generalengineering purposes - Technical delivery conditions - Part 2:Stainless st

8、eelTubes ronds souds en acier pour utilisation en mcaniquegnrale et en construction mcanique - Conditionstechniques de livraison - Partie 2: Tubes en acierinoxydableGeschweite kreisfrmige Stahlrohre fr denMaschinenbau und allgemeine technische Anwendungen -Technische Lieferbedingungen - Teil 2: Nich

9、trostendeSthleThis European Standard was approved by CEN on 4 April 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliograp

10、hical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN m

11、ember into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith

12、uania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All righ

13、ts of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10296-2:2005: EEN 10296-2:2005 (E) 2 Contents Page Foreword 3 Introduction4 1 Scope .5 2 Normative references .5 3 Terms and definitions.6 4 Symbols.6 5 Classification and designation 6 6 Informati

14、on to be supplied by the purchaser7 7 Manufacturing process.8 8 Requirements 9 9 Inspection and testing 18 10 Sampling20 11 Test methods.22 12 Marking 24 13 Handling and packaging.25 Annex A (normative) Process route and surface conditions 26 Annex B (informative) Guideline data on heat treatment du

15、ring fabrication and hot working as part of further processing 27 Annex C (normative) Formulae for calculation of nominal sectional properties .30 Bibliography.31 EN 10296-2:2005 (E) 3 Foreword This document (EN 10296-2:2005) has been prepared by Technical Committee ECISS/TC 29 “Steel tubes and fitt

16、ings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the latest by Ju

17、ne 2006. Another part of EN 10296 is: Part 1: Non-alloy and alloy steel tubes Another European Standard series, covering seamless steel tubes for mechanical and general engineering purposes, currently being prepared is: EN 10297: Seamless circular steel tubes for mechanical and general engineering p

18、urposes Technical delivery conditions. Other series of European Standards being prepared in this area are prEN 10294 - hollow bars for machining and EN 10305 - steel tubes for precision applications. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follo

19、wing countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden

20、, Switzerland and United Kingdom. EN 10296-2:2005 (E) 4 Introduction The European Committee for Standardisation (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of patents applied to steel grades 1.4362 and 1.4854, the compositions of which

21、are given in Tables 1 and 2. CEN takes no position concerning the evidence, validity and scope of these patent rights. The holders of these patent rights have assured CEN that they are willing to negotiate licences, under reasonable and non-discriminatory terms and conditions, with applicants throug

22、hout the world. In this respect, the statements of the holders of these patent rights are registered with CEN. Information may be obtained from: Grade 1.4362 Sandvik AB SE-811 81 SANDVIKEN Sweden Grade 1.4854 Outokumpu OYJ Intelectual Property Management P.O Box 27 FI 02201 ESPOO Finland Attention i

23、s drawn to the possibility that some of the elements within this European Standard may be the subject of patent rights other than those indicated above. CEN shall not be responsible for identifying any or all such patent rights. EN 10296-2:2005 (E) 5 1 Scope This European Standard specifies the tech

24、nical delivery conditions for welded tubes, of circular cross section, made from stainless steels, for mechanical and general engineering purposes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition

25、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 910, Destructive tests on welds in metallic materials - Bend tests EN 10002-1, Metallic materials Tensile testing Part 1: Method of test (at ambient temperature) EN 10020:2000

26、, Definition and classification of grades of steel EN 10021:1993, General technical delivery requirements for steel and iron products EN 10027-1, Designation systems for steel Part 1: Steel names, principal symbols EN 10027-2, Designation systems for steel Part 2: Numerical system EN 10052:1993, Voc

27、abulary of heat treatment terms for ferrous products EN 10088-1, Stainless steels Part 1: List of stainless steels EN 10168, Steel products Inspection documents List of information and description EN 10204, Metallic products Types of inspection documents EN 10246-2, Non-destructive testing of steel

28、tubes Part 2: Automatic eddy current testing of seamless and welded (except submerged arc-welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightness EN 10246-3, Non-destructive testing of steel tubes Part 3: Automatic eddy current testing of seamless and weld

29、ed (except submerged arc-welded) steel tubes for the detection of imperfections EN 10246-7, Non-destructive testing of steel tubes Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal imperfections EN

30、10246-8, Non-destructive testing of steel tubes Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections EN 10246-9, Non-destructive testing of steel tubes Part 9: Automatic ultrasonic testing of the weld seam of submerged a

31、rc welded steel tubes for the detection of longitudinal and/or transverse imperfections EN 10246-10, Non-destructive testing of steel tubes Part 10: Radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections EN 10256, Non-destructive testing o

32、f steel tubes Qualification and competence of level 1 and 2 non-destructive testing personnel. EN 10266:2003, Steel tubes, fittings and steel structural hollow sections - Symbols and definitions of terms for use in product standards. CR 10260:1998, Designation system for steel Additional symbols EN

33、10296-2:2005 (E) 6 EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 8491, Metallic materials Tube (in full section) - Bend test (ISO 8491:1998) EN ISO 8492, Metallic materials Tube - Flattening test (ISO 8492:1998)

34、EN ISO 8493, Metallic materials Tube - Drift expanding test (ISO 8493:1998) EN ISO 8496, Metallic materials Tube - Ring tensile test (ISO 8496:1998) EN ISO 1127, Stainless steel tubes Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992). EN ISO 2566-2, Steel Conversion of e

35、longation values Part 2: Austenitic steels (ISO 2566-2:1984) EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) 3 T

36、erms and definitions For the purposes of this European Standard, the terms and definitions given in EN 10020:2000, EN 10021:1993, EN 10052:1993 and EN 10266:2003 together with the following apply. employer organisation for which the person works on a regular basis NOTE The employer may be either the

37、 tube manufacturer or a third party organisation providing non-destructive testing (NDT) services. 4 Symbols For the purposes of this European Standard, the symbols given in EN 10266:2003 and CR 10260:1998 apply. Not applicable. 5 Classification and designation 5.1 Classification In accordance with

38、the classification system in EN 10020, the steel grades listed in Tables 1 and 2 are stainless steels. 5.2 Designation For tubes covered by this document the steel designation consists of: number of this document (EN 10296-2); plus either: steel name in accordance with EN 10027-1 and CR 10260; or st

39、eel number allocated in accordance with EN 10027-2. EN 10296-2:2005 (E) 7 6 Information to be supplied by the purchaser 6.1 Mandatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) quantity (mass or total length or number); b) term “tube

40、“; c) dimensions (outside diameter D, wall thickness T) (see 8.7); d) steel designation (see 5.2); e) delivery condition for austenitic and austenitic-ferritic grades (see 7.2.2). 6.2 Options A number of options are specified in this document and these are listed below with appropriate clause refere

41、nces. In the event that the purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, the tube shall be supplied in accordance with the basic specification (see 6.1). 1) process route and /or surface condition (see 7.2.1); 2) weld bead finish (see 7.2.1);

42、 3) pickled tube (see 7.2.2); 4) controlled sulphur content (see Table 1); 5) non-destructive testing of the weld (see 8.4.2); 6) leak tightness test (see 8.4.2); 7) straightness (see 8.5); 8) random lengths (see 8.7.2); 9) exact lengths (see 8.7.2); 10) outside diameter tolerances (see 8.7.3.1) 11)

43、 specific inspection and testing (see 9.1); 12) test report 2.2 (see 9.2.1); 13) inspection document, 3.2 (see 9.2.1); 14) leak tightness test method (see 11.7.1). 6.3 Example of an order Fifteen tonnes of welded steel tubes with a specified outside diameter of 60,3 mm, a specified wall thickness of

44、 3,2 mm, in accordance with EN 10296-2, made from steel grade 1.4301, solution annealed, (supplied in 6 m standard length) and with a test report 2.2 (option 12) in accordance with EN 10204. 15 t Tube - 60,3 x 3.2 - EN 10296-2 - 1.4301+AT- option 12 EN 10296-2:2005 (E) 8 7 Manufacturing process 7.1

45、Steelmaking process The steelmaking process is at the discretion of the manufacturer. 7.2 Tube manufacturing and delivery conditions 7.2.1 Tubes shall be produced from hot or cold rolled strip or plate/sheet, longitudinally welded across the abutting edges, by a continuous automatic process with or

46、without the addition of filler metal. The welding process is at the discretion of the manufacturer. Acceptable process routes and surface conditions are given in Table A.1. The choice of process route, base material, hot or cold rolled feedstock and the surface condition, is at the discretion of the

47、 manufacturer unless Option 1 is specified. Option 1: The process route and/or surface condition is specified by the purchaser from those in Table A.1. Tubes shall be delivered with one of the following weld bead finishes: Finish A: Internal and external weld bead not removed; Finish B: External wel

48、d bead removed internal weld bead not removed; Finish C: Internal and external weld bead rolled or removed. Finish A shall not be used for high frequency (HF) welded tube. The weld bead finish is at the discretion of the manufacturer unless Option 2 is specified. Option 2: The weld bead finish; A, B

49、 or C is specified by the purchaser. The finished tubes shall not include the welds used to join the lengths of strip prior to forming the tube. However jointers are permitted when the purchaser specifies lengths in excess of the production maximum, if agreed at the time of enquiry and order. 7.2.2 Tubes produced in accordance with 7.2.1 shall be delivered in the following delivery conditions: - ferritic steels: as welded (+AR) or annealed (+A), at the discretion of the manufacturer;