EN 10028-2-2017 en Flat products made of steels for pressure purposes - Part 2 Non-alloy and alloy steels with specified elevated temperature properties.pdf

《EN 10028-2-2017 en Flat products made of steels for pressure purposes - Part 2 Non-alloy and alloy steels with specified elevated temperature properties.pdf》由会员分享，可在线阅读，更多相关《EN 10028-2-2017 en Flat products made of steels for pressure purposes - Part 2 Non-alloy and alloy steels with specified elevated temperature properties.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、Flat products made of steels for pressure purposesPart 2: Non-alloy and alloy steels with specified elevated temperature propertiesBS EN 10028-2:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-2 July 2017

2、 ICS 77.140.30; 77.140.50 Supersedes EN 10028-2:2009English Version Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties Produits plats en aciers pour appareils pression - Partie 2 : Aciers non allis et allis avec cara

3、ctristiques spcifies temprature leve Flacherzeugnisse aus Druckbehltersthlen - Teil 2: Unlegierte und legierte Sthle mit festgelegten Eigenschaften bei erhhten Temperaturen This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulat

4、ions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

5、 This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN

6、members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

7、rtugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitatio

8、n in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-2:2017 ENational forewordThis British Standard is the UK implementation of EN 10028-2:2017. It supersedes BS EN 10028-2:2009, which is withdrawn.The UK participation in its preparation was entrusted to Tech

9、nical Committee ISE/107, Steels for Pressure Purposes.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Brit

10、ish Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 87854 1ICS 77.140.50; 77.140.30Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee

11、 on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affected BRITISH STANDARDBS EN 10028-2:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10028-2 July 2017 ICS 77.140.30; 77.140.50 Supersedes EN 10028-2:2009English Version Flat products made of steels for pressure pu

12、rposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties Produits plats en aciers pour appareils pression - Partie 2 : Aciers non allis et allis avec caractristiques spcifies temprature leve Flacherzeugnisse aus Druckbehltersthlen - Teil 2: Unlegierte und legierte S

13、thle mit festgelegten Eigenschaften bei erhhten Temperaturen This European Standard was approved by CEN on 7 May 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

14、any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lang

15、uage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar

16、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COM

17、MITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10028-2:2017 EBS EN 1002

18、8-2:2017EN 10028-2:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Tolerances on dimensions . 4 5 Calculation of mass . 4 6 Classification and designation . 4 6.1 Classification . 4 6.2 Designation . 4 7 Information to be supplied by the

19、purchaser . 5 7.1 Mandatory information 5 7.2 Options 5 7.3 Example for ordering. 5 8 Requirements . 6 8.1 Steelmaking process 6 8.2 Delivery condition 6 8.3 Chemical composition . 6 8.4 Mechanical properties 10 8.5 Surface condition 10 8.6 Internal soundness . 10 8.7 Resistance to hydrogen induced

20、cracking . 10 8.8 Embrittlement of CrMo steels . 10 9 Inspection 10 9.1 Types of inspection and inspection documents . 10 9.2 Tests to be carried out 10 9.3 Retests, sorting and reprocessing . 10 10 Sampling . 10 11 Test methods 10 12 Marking 11 Annex A (informative) Guidelines for heat treatment 17

21、 Annex B (informative) Critical time temperature parameter Pcrit.and possible combinations of stress relieving temperature and holding time 18 Annex C (informative) Reference data of strength values for 1 % (plastic) creep strain and creep rupture . 20 Annex D (normative) Evaluation of resistance to

22、 hydrogen induced cracking . 26 Annex E (normative) Step cooling test . 27 Annex F (informative) Changes to the previous version EN 10028-2:2009 28 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of European Directive 2014/68/EU 29 Bibliography 30 BS

23、 EN 10028-2:2017EN 10028-2:2017 (E) 3 European foreword This document (EN 10028-2:2017) has been prepared by Technical Committee ECISS/TC 107 “Steels for pressure purposes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by pu

24、blication of an identical text or by endorsement, at the latest by January 2018 and conflicting national standards shall be withdrawn at the latest by January 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELE

25、C shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10028-2:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of Directive 2

26、014/68/EU. For relationship with Directive 2014/68/EU, see informative Annex ZA, which is an integral part of this document. A list of changes between this document and the previous version can be found in Annex F. According to the CEN-CENELEC Internal Regulations, the national standards organizatio

27、ns of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

28、 Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10028-2:2017EN 10028-2:2017 (E) 4 1 Scope This European Standard specifies requirements for flat products for pressure equipment made of weldable non-alloy an

29、d alloy steels with elevated temperature properties as specified in Table 1. The requirements and definitions of EN 10028-1:2017 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety R

30、equirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and this Part 2 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this mater

31、ial standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for

32、its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1011-1:2009, Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding EN 1

33、011-2:2001, Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic steels EN 10028-1:2017, Flat products made of steels for pressure purposes - Part 1: General requirements EN 10204:2004, Metallic products - Types of inspection documents EN 10229:1998, Evaluati

34、on of resistance of steel products to hydrogen induced cracking (HIC) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10028-1:2017 apply. 4 Tolerances on dimensions See EN 10028-1:2017. 5 Calculation of mass See EN 10028-1:2017. 6 Classification and d

35、esignation 6.1 Classification In accordance with EN 10020, the grades P235GH, P265GH, P295GH and P355GH are non-alloy quality steels. All other grades are alloy special steels. 6.2 Designation See EN 10028-1:2017. BS EN 10028-2:2017EN 10028-2:2017 (E) 5 7 Information to be supplied by the purchaser

36、7.1 Mandatory information See EN 10028-1:2017. 7.2 Options A number of options are specified in this document and listed below. Additionally the relevant options of EN 10028-1:2017 apply. If the purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, th

37、e products shall be supplied in accordance with the basic specification (see also EN 10028-1:2017). 1) limitation of copper and/or tin content (see Table 1, footnote b); 2) minimum chromium content of 0,80 % (see Table 1, footnote f); 3) maximum carbon content of 0,17 % for nominal thicknesses great

38、er than 150 mm (see Table 1, footnote g); 4) tests in the simulated normalized condition (see 8.2.2); 5) delivery conditions deviating from those specified in Table 3 (see 8.2.2 and 8.2.3); 6) maximum carbon equivalent value for P235GH, P265GH, P295GH and P355GH (see 8.3.3); 7) specification of a mi

39、nimum impact energy of 40 J (see Table 3); 8) no option, intentionally left blank; 9) specification of the delivery condition +QT where the usual delivery condition is +NT (see Table 3, footnote b and Table 4, footnote b); 10) additional impact energy values (see Table 3, footnote e); 11) no option,

40、 intentionally left blank; 12) HIC test in accordance with EN 10229 (see 8.7); 13) step cooling test in accordance with Annex E (see 8.8); 14) mid thickness test pieces for the impact test (see Clause 10). 7.3 Example for ordering 10 plates with nominal dimensions, thickness = 50 mm, width = 2 000 m

41、m, length = 10 000 mm, made of a steel grade with the name 16Mo3 and the number 1.5415 as specified in EN 10028-2, inspection certificate 3.1 as specified in EN 10204: 10 plates 50 2 000 10 000 EN 10028-2 16Mo3 Inspection certificate 3.1 or 10 plates 50 2 000 10 000 EN 10028-2 1.5415 Inspection cert

42、ificate 3.1 BS EN 10028-2:2017EN 10028-2:2017 (E) 6 8 Requirements 8.1 Steelmaking process See EN 10028-1:2017. 8.2 Delivery condition 8.2.1 Unless otherwise agreed at the time of enquiry and order, the products covered by this document shall be supplied in the usual conditions given in Table 3 (see

43、 8.2.3). 8.2.2 Normalizing may, at the discretion of manufacturer, be replaced with normalizing rolling for the steel grades P235GH, P265GH, P295GH, P355GH and 16Mo3. In this case, additional tests in the simulated normalized condition with an agreed frequency of testing may be agreed at the time of

44、 enquiry and order to verify that the specified properties are complied with. 8.2.3 If so agreed at the time of enquiry and order, products made of steel grades P235GH, P265GH, P295GH, P355GH and 16Mo3 may also be delivered in the untreated condition. Products made of one of the other alloy grades m

45、ay be supplied in the tempered or normalized condition or, in exceptional cases, in the untreated condition if so agreed (Annex A contains heat treatment information for the purchaser). In these cases, testing shall be carried out on test pieces in the usual delivery condition as indicated in Table

46、3. 8.2.4 Information on welding are given in Annex B of this standard. 8.3 Chemical composition 8.3.1 The requirements of Table 1 shall apply for the chemical composition according to the cast analysis. 8.3.2 The product analysis shall not deviate from the specified values for the cast analysis as s

47、pecified in Table 1 by more than the values given in Table 2. 8.3.3 A maximum value for the carbon equivalent may be agreed at time of enquiry and order for steel grades P235GH, P265GH, P295GH and P355GH. In this case, the following formula shall apply for calculation of the carbon equivalent value

48、(CEV): + +=+ +6 5 15Mn Cr Mo V Ni CuCEV C BS EN 10028-2:2017EN10028-2:2017(E)7Table1 Chemicalcomposition(castanalysis)aSteeldesignation%bymassSteelnameSteelnumberCSiMnPmax.Smax.AltotalNCrCubMoNbNiTimax.VOthersP235GH1.03450,160,350,60cto 1,200,0250,0100,0200,012d0,300,300,080,0300,300,030,02Cr+Cu+Mo+

49、Ni0,70P265GH1.04250,200,400,80cto 1,400,0250,0100,0200,012d0,300,300,080,0300,300,030,02P295GH1.04810,08to0,200,400,90cto 1,500,0250,0100,0200,012d0,300,300,080,0300,300,030,02P355GH1.04730,10to0,220,601,10to1,700,0250,0100,0200,012d0,300,300,080,0400,300,030,0216Mo31.54150,12to0,200,350,40to0,900,0250,010e0,0120,300,300,25to0,35-0,30-18MnMo451.54140,200,400,90to1,500,0150,005e0,0120,300,300,45to0,60-0,30-20MnMoNi451.63110,15to0,230,401,00to1,500,0200,010e0,