ECMA 195-1995 Data Interchange on 130 mm Optical Disk Cartridges - Capacity 2 Gigabytes per Cartridge《130 mm盒式光盘上的数据交换 容量 2 Gbytes 盒 第2版》.pdf

《ECMA 195-1995 Data Interchange on 130 mm Optical Disk Cartridges - Capacity 2 Gigabytes per Cartridge《130 mm盒式光盘上的数据交换 容量 2 Gbytes 盒 第2版》.pdf》由会员分享，可在线阅读，更多相关《ECMA 195-1995 Data Interchange on 130 mm Optical Disk Cartridges - Capacity 2 Gigabytes per Cartridge《130 mm盒式光盘上的数据交换 容量 2 Gbytes 盒 第2版》.pdf（164页珍藏版）》请在麦多课文档分享上搜索。

1、Standard ECMA-1952nd Edition - June 1995Standardizing Information and Communication SystemsPhone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL: http:/www.ecma.ch - Internet: helpdeskecma.chData Interchange on 130 mmOptical Disk Cartridges -Capacity: 2 Gigabytes perCartridgeStandard ECMA-1952nd Edi

2、tion - June 1995Standardizing Information and Communication SystemsPhone: +41 22 849.60.00 - Fax: +41 22 849.60.01 - URL: http:/www.ecma.ch - Internet: helpdeskecma.chMB- ECMA-195.DOC - 12.03.96 11,28Data Interchange on 130 mmOptical Disk Cartridges -Capacity: 2 Gigabytes perCartridgeBrief HistoryTe

3、chnical Committee ECMA TC31 for Optical Disk Cartridges (ODC) was set up in 1984. The committee made majorcontributions to ISO/IEC JTC1/SC23 for the development of 130 mm WORM Optical Disk Cartridges (ISO/IEC 9171) and of130 mm Rewritable Optical Disk Cartridges using M.O. (ISO/IEC 10089). ECMA prod

4、uced camera-ready copies for theseInternational Standards. In addition ECMA published the following Standards:ECMA-130 (1988) Data Interchange on Read-only 120 mm Optical Data Disks (CD-ROM)ECMA-153 (1994) Information Interchange on 130 mm Optical Disk Cartridges of the Write Once,Read Multiple Type

5、, using the Magneto-Optical EffectECMA-154 (1994) Data Interchange on 90 mm Optical Disk Cartridges, Read Only and Rewritable, M.O.ECMA-183 (1992) Data Interchange on 130 mm Optical Disk Cartridges - Capacity: 1 Gbyte per CartridgeECMA-184 (1992) Data Interchange on 130 mm Optical Disk Cartridges -

6、Capacity: 1,3 Gbytes per CartridgeECMA-201 (1994) Data Interchange on 90 mm Optical Disk Cartridges - Capacity: 230 Mbytes per CartridgeThese ECMA Standards have been adopted unter the fast track procedure of ISO/IEC as International Standards ISO/IEC10149, ISO/IEC 11560, ISO/IEC 10090, ISO/IEC 1384

7、1, ISO/IEC 13549 and ISO/IEC 13963, respectively.Standards ECMA-183 and ECMA-184 are the first of a series of ECMA Standards for ODCs of different capacities, based onthe optical disk cartridge specified in ISO/IEC 10089. Whilst the latter specifies a fully re-writable disk, these ECMAStandards spec

8、ify several related implementations depending on the application considered. Two or more Types are defined,including fully re-writable, partially pre-recorded and partially re-writable, fully pre-recorded disks or cartridges and those withwrite once, read multiple functionality.The present standard

9、is a further ECMA Standard of this series. It specifies nine Types providing a capacity of 2 Gbytes percartridge. It is identical to International Standard ISO/IEC 13842.Adopted as 2nd Edition of Standard ECMA-195 by the ECMA General Assembly in June 1995.- i -Table of contentsSection 1: General 11

10、Scope 12 Conformance 12.1 Optical Disk Cartridge (ODC) 12.2 Generating system 22.3 Receiving system 22.4 Compatibility statement 23 Reference 24 Definitions 24.1 band 24.2 case 24.3 clamping zone 24.4 control track 24.5 Cyclic Redundancy Check (CRC) 24.6 defect management 24.7 disk reference plane 2

11、4.8 entrance surface 24.9 Error Correction Code (ECC) 24.10 format 24.11 hub 34.12 interleaving 34.13 Kerr rotation 34.14 land and groove 34.15 logical track 34.16 mark 34.17 mark edge 34.18 mark edge recording 34.19 optical disk 34.20 optical disk cartridge (ODC) 34.21 physical track 34.22 polariza

12、tion 34.23 pre-recorded mark 34.24 read power 34.25 recording layer 44.26 Reed-Solomon code 44.27 spindle 44.28 substrate 44.29 track pitch 44.30 write-inhibit hole 44.31 write once functionality 44.32 zone45 Conventions and notations 45.1 Representation of numbers 45.2 Names 46 List of acronyms 5-

13、ii -7 General description of the optical disk cartridge 58 General requirements 58.1 Environments 58.1.1 Test environment 58.1.2 Operating environment 68.1.3 Storage environment 68.1.4 Transportation 68.2 Temperature shock 68.3 Safety requirements 68.4 Flammability 79 Reference Drive 79.1 Optical sy

14、stem 79.2 Optical beam 99.3 Read channels 99.4 Tracking 99.5 Rotation of the disk 9Section 2 : Mechanical and physical characteristics 1010 Dimensional and physical characteristics of the case 1010.1 General description of the case 1010.2 Relationship of Sides A and B 1010.3 Reference axes and case

15、reference planes 1010.4 Case drawings 1010.5 Dimensions of the case 1010.5.1 Overall dimensions 1010.5.2 Location hole 1110.5.3 Alignment hole 1110.5.4 Surfaces on Reference Planes P 1210.5.5 Insertion slots and detent features 1310.5.6 Gripper slots 1310.5.7 Write-inhibit holes 1310.5.8 Media senso

16、r holes 1410.5.9 Head and motor window 1510.5.10 Shutter 1610.5.11 Slot for shutter opener 1610.5.12 Shutter sensor notch 1710.5.13 User label areas 1710.6 Mechanical characteristics 1710.6.1 Materials 1710.6.2 Mass 1710.6.3 Edge distortion 1710.6.4 Compliance 1710.6.5 Shutter opening force 1710.7 D

17、rop test 1811 Dimensional, mechanical and physical characteristics of the disk 1811.1 General description of the disk 1811.2 Reference axis and plane of the disk 1811.3 Dimensions of the disk 18- iii -11.3.1 Hub dimension 1811.4 Mechanical characteristics 1911.4.1 Material 1911.4.2 Mass 1911.4.3 Mom

18、ent of inertia 1911.4.4 Imbalance 1911.4.5 Axial deflection 1911.4.6 Axial acceleration 2011.4.7 Radial runout 2011.4.8 Radial acceleration 2011.4.9 Tilt 2111.5 Optical characteristics 2111.5.1 Index of refraction 2111.5.2 Thickness 2111.5.3 Birefringence 2111.5.4 Reflectance 2112 Interface between

19、cartridge and drive 2112.1 Clamping method 2112.2 Clamping force 2112.3 Capture cylinder 2212.4 Disk position in the operating condition 22Section 3 : Format of information 3713 Track geometry 3713.1 Track shape 3713.2 Direction of track spiral 3713.3 Track pitch 3713.4 Logical track number 3713.5 P

20、hysical track number 3714 Track format 3714.1 Physical track layout 3714.2 Logical track layout 3814.3 Radial alignment 3814.4 Sector number 3815 Sector format 3815.1 Sector layout 3815.2 Sector mark 3915.3 VFO fields 4015.4 Address Mark (AM) 4015.5 ID fields 4115.6 Postamble (PA) 4115.7 Gap 4115.8

21、Auto Laser Power Control (ALPC) 4215.9 Sync 4215.10 Data field 4215.10.1 User data bytes 4215.10.2 CRC and ECC bytes 4215.10.3 Bytes for control information (DMP) 4215.10.4 Last bytes of the data field of the 512-byte sector format 43- iv -15.10.5 Resync bytes 4315.11 Buffer field 4316 Recording cod

22、e 4317 Formatted Zone 4417.1 General description of the Formatted Zone 4417.2 Division of the Formatted Zone 4417.2.1 Lead-in Zone 4617.2.2 Manufacturer Zones 4617.2.3 User Zone 4717.2.4 Reflective Zone 4717.2.5 Control Track Zones 4717.3 Control Track PEP Zone 4717.3.1 Recording in the PEP Zone 471

23、7.3.2 Format of the tracks of the PEP Zone 4817.4 Control Track SFP Zones 5117.4.1 Duplicate of the PEP information 5117.4.2 Media information 5117.4.3 System Information 5618 Layout of the User Zone 5718.1 General description of the User Zone 5718.2 Divisions of the User Zone 5718.3 User Area 5818.

24、4 Defect Management Areas (DMAs) 6418.5 Disk Definition Structure 6518.6 Rewritable Zone 6718.6.1 Location 6818.6.2 Partitioning 6818.7 Embossed Zone 6818.7.1 Location 6818.7.2 Partitioning 6818.7.3 Parity sectors 6818.8 Write Once Zone 6918.8.1 Location 6918.8.2 Partitioning 6919 Defect Management

25、in the Rewritable and Write Once Zones 6919.1 Initialization of the disk 6919.2 Certification 6919.2.1 Slipping Algorithm 6919.2.2 Linear Replacement Algorithm 7019.3 Disks not certified 7019.4 Write procedure 7019.5 Primary Defect List (PDL) 7019.6 Secondary Defect List (SDL) 71- v -Section 4 : Cha

26、racteristics of embossed information 7320 Method of testing 7320.1 Environment 7320.2 Use of the Reference Drive 7320.2.1 Optics and mechanics 7320.2.2 Read power 7320.2.3 Read channels 7320.2.4 Tracking 7320.3 Definition of signals 7321 Signal from grooves 7421.1 Cross-track signal modulation ratio

27、 7521.2 Cross-track minimum signal ratio 7521.3 Push-pull ratio 7521.4 Divided push-pull signal 7621.5 On-track signal ratio 7621.6 Phase depth 7621.7 Track location 7722 Signals from Headers 7722.1 Sector Mark Signals 7722.2 VFO signals 7722.3 Address Mark, ID and PA signals 7722.4 Timing jitter 77

28、23 Signals from embossed Recording fields 7823.1 Signal amplitude 7823.2 Modulation method offset 7823.3 Timing Jitter 7824 Signals from Control Track PEP marks 78Section 5 : Characteristics of the recording layer 8025 Method of testing 8025.1 Environment 8025.2 Reference Drive 8025.2.1 Optics and m

29、echanics 8025.2.2 Read power 8025.2.3 Read Channel 8025.2.4 Tracking 8025.2.5 Signal detection for testing purposes 8025.3 Write conditions 8125.3.1 Write pulse and power 8125.3.2 Write magnetic field and temperature 8125.3.3 2T and 4T pulse power determination 8125.3.4 Media power sensitivity 8125.

30、4 Erase conditions 8225.4.1 Erase power 8225.4.2 Erase magnetic field 82- vi -25.5 Definition of signals 8226 Magneto-optical characteristics 8226.1 Figure of merit for magneto-optical signal 8226.2 Imbalance of magneto-optical signal 8227 Write characteristics 8327.1 Resolution 8327.2 Narrow-band s

31、ignal-to-noise ratio 8327.3 Cross-talk ratio 8427.3.1 Rewritable track test method 8427.3.2 Embossed track test method 8427.4 Timing Jitter 8527.5 Media thermal build-up during mark formation 8528 Erase power determination 86Section 6 : Characteristics of user data 8729 Method of testing 8729.1 Envi

32、ronment 8729.2 Reference Drive 8729.2.1 Optics and mechanics 8729.2.2 Read power 8729.2.3 Read amplifiers 8729.2.4 Mark Quality 8729.2.5 Channel bit clock 8829.2.6 Binary-to-digital converters 8829.2.7 Error correction 8829.2.8 Tracking 8830 Minimum quality of a sector 8830.1 Headers 8830.1.1 Sector

33、 Mark 8830.1.2 D fields 8830.2 User-written data 8830.2.1 Byte errors 8830.2.2 Modulation method offset 8830.2.3 Timing jitter 8830.3 Embossed data 8830.3.1 Byte errors 8830.3.2 Modulation method offset 8930.3.3 Timing jitter 8931 Data interchange requirements 8931.1 Tracking 8931.2 User-written dat

34、a 8931.3 Embossed data 8931.4 Quality of disk 89- vii -AnnexesAnnex A - Air cleanliness 100 000 91Annex B - Edge distortion test 93Annex C - Compliance test 95Annex D - Test method for measuring the adsorbent force of the hub 97Annex E - CRC for ID fields 99Annex F - Interleave, CRC, ECC, Resync for

35、 the data field 101Annex G - Determination of Resync pattern 107Annex H - Read Channel for measuring C/N and jitter 113Annex J - Timing jitter measuring procedure 115Annex K - Definition of write pulse shape 117Annex L - Measurement of figure of merit 119Annex M - Implementation Independent Mark Qua

36、lity Determination (IIMQD) for the interchange ofrecorded media 121Annex N - Requirements for interchange 123Annex P - Office environment 125Annex Q - Derivation of the operating climatic environment 127Annex R - Transportation 133Annex S - Sector retirement guidelines 135Annex T - Track deviation m

37、easurement 137Annex U - Values to be implemented in existing and future standards 141Annex V - Guidelines for the use of Type WO ODCs 143- 1 -Section 1: General1 ScopeThis ECMA Standard specifies the characteristics of a series of related 130 mm optical disk cartridges (ODCs) byusing a number of Typ

38、e designations.The two sides of the disk, called Side A and Side B, with each a nominal storage capacity of 1 Gigabyte are givenspecific Type designations. Thus, Side A and Side B may be different types.Types R/W, R/W-R provide for data to be written, read and erased many times over the whole of bot

39、hrecording surfaces of the corresponding disk side, using the thermo-magnetic andmagneto-optical effects.Types P-ROM, P-ROM-R provide for part of both disk surfaces to be pre-recorded and reproduced by stampingor other means. This part of the disk is read without recourse to the magnetico-optical ef

40、fect. All parts which are not pre-recorded provide for data to meet therequirements of Types R/W and R/W-R, respectively.Types O-ROM, O-ROM-R provide for the whole of both disk surfaces to be pre-recorded and reproduced bystamping or other means. The disk sides are read without recourse to the magne

41、to-optical effects.Types WO, WO-R provide write-once, read-multiple functionality using the thermo-magnetic and themagneto-optical effects.Type B indicates that the cartridge side shall not be used. This Type designation may be usedfor Side B only.The suffix - R, which may be used for Side B only, i

42、ndicates that the tracks of Side B spiral in the opposite direction tothose on Side A. Such ODCs facilitate simultaneous access to both sides of the disk by a dual optical system.The 20 combinations of Types allowed by this ECMA Standard for the two sides of disks are specified in table 2 in10.5.8.I

43、n addition, for each Type, this ECMA Standard provides for 512-byte and 1 024-byte sector sizes. All sectors of anODC are the same size.This ECMA Standard specifies the conditions for conformance testing and the Reference Drive; the environments in which the cartridges are to be operated and stored;

44、 the mechanical, physical and dimensional characteristics of the cartridge, so as to provide mechanicalinterchangeability between data processing systems; the format of the information on the disk, both embossed and user-written, including the physical disposition of thetracks and sectors, the error

45、 correction codes, the modulation methods used; the characteristics of the embossed information on the disk; the magneto-optical characteristics of the disk, enabling processing systems to write data onto the disk; the minimum quality of user-written data on the disk, enabling data processing system

46、s to read data from the disk.This ECMA Standard provides for interchange between optical disk drives. Together with a Standard for volume andfile structure it provides for full data interchange between data processing systems.2 Conformance2.1 Optical Disk Cartridge (ODC)An ODC claiming conformance w

47、ith this ECMA Standard shall specify the Type of its two sides. It shall be inconformance if it meets all mandatory requirements specified herein for those Types of sides.- 2 -2.2 Generating systemA claim of conformance with this ECMA Standard shall specify which of Types R/W, R/W-R, P-ROM, P-ROM-R,

48、O-ROM, O-ROM-R, WO, WO-R, and B is(are) supported. A system generating an ODC for interchange shall beentitled to claim conformance with this ECMA Standard if it meets the mandatory requirements of this Standard forthe Type(s) supported.2.3 Receiving systemA claim of conformance with this ECMA Stand

49、ard shall specify which Type(s) of side(s) is(are) supported.A system receiving an ODC for interchange shall be entitled to claim conformance with this ECMA Standard if it isable to handle any recording made on the cartridge according to 2.1 on the Types specified.2.4 Compatibility statementA claim of conformance by a generating or receiving system with this ECMA Standard shall include a statementlisting any other ECMA or International Optical Disk Cartridge Standard supported. This statement shall specify thenumber of the Standard(s), including, where appropriate, the ODC Type(s),