ECA EIA-784-1998 Guideline for Reel Configuration and Dimensions for Reel Diameters Larger Than 360 mm (Utilized in Applications of 16 mm to 56 mm Carrier Taping)《直径大于360毫米的卷盘构造和尺寸.pdf

《ECA EIA-784-1998 Guideline for Reel Configuration and Dimensions for Reel Diameters Larger Than 360 mm (Utilized in Applications of 16 mm to 56 mm Carrier Taping)《直径大于360毫米的卷盘构造和尺寸.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-784-1998 Guideline for Reel Configuration and Dimensions for Reel Diameters Larger Than 360 mm (Utilized in Applications of 16 mm to 56 mm Carrier Taping)《直径大于360毫米的卷盘构造和尺寸.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、I w 0 .EIA GUIDELINE Guideline for Reel Configuration and Dimensions for Reel Diameters Larger than 360 mm (Utilized in Applications of 16 mm to 56 mm Carrier Taping) EIA-784 DECEMBER 1998 ELECTRONIC INDUSTRIES ALLIANCE ENGINEERING DEPARTMENT I Electronic Industries Alliance NOTICE . EIA Engineering

2、 Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchasers in selecting and obtaining with minimum delay the proper product

3、 for their particular needs. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude the

4、ir voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EIA does not assume any liabil

5、ity to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Technical Publications are distinguished from EIA Standards or Interim Standards, in that they contain a compilation of engineering data or information useful to the technical communi

6、ty and represent approaches to good engineering practices that are suggested by the formulating committee. This publication is not intended to preclude or discourage other approaches that similarly represent good engineering practice, or that may be acceptable to, or have been accepted by, appropria

7、te bodies. Parties who wish to bring other approaches to the attention of the formulating committee to be considered for inclusion in future revisions of this publication are encouraged to do so. It is the intention of the formulating committee to revise and update this publication from time to time

8、 as may be occasioned by changes in technology, industry practice, or govemment regulations, or for other appropriate reasons. (From Project No. 4419, formulated under the cognizance of the EIA Automated Component Handling (ACH) Committee.) Published by ELECTRONIC INDUSTRIES ALLIANCE 1998 Engineerin

9、g Department 2500 Wilson Boulevard Arlington, VA 2220 1 PRICE: Please refer to the current or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) Catalog of EL4 Electronic Industries Alliance Standards and Engineering Publications AU rights reserved Printe

10、d in U.S.A. STD-EIA 784-ENGL 1998 323Lib00 Ob12227 i08 E EIA-784 GUIDELINE FOR REEL CONFIGURATION AND DIMENSIONS FOR REEL DIAMETERS LARGER THAN 360mm (Utilized in Applications of 16mm to 56mm Carrier Taping) Page 1 Scope 2 Introduction 3 Applicable EIA Documents EDITORIAL ADDITIONS Editorial Additio

11、n to EIA-481-2 Editorial Addition to EIA-48 1-3 (16mm and 24mm Carrier Tape) (32mm, 44mm, and 56mm Carrier Tape) 2 3 i EIA-784 Page 1 1 Scope This guideline is to be utilized with the ELA standards listed under Clause 3 below 2 Introduction The intent of this EIA Guideline is to provide an editorial

12、 addition to two subparts of the ANSEIA 48 1 series (48 1-2 and 48 i-3), pertaining to a guideline for reel configuration and dimensions of reel diameters larger than 360mm (utilized in applications of 16mm to 56mm carrier taping) without necessitating the revision of these EIA Automated Component H

13、andling (ACH) publications at the present time. The editorial additions are divided into two sections containing advisory notes relative to widely used reel sizes and corresponding hub diameters. The first section (Page 2) covers 16mm and 24mm carrier tapes and is applicable to ELA-481-2. The second

14、 section (Page 3) covers 32mm, 44mm, and 56mm carrier tapes and is applicable to EIA-481-3. This guideline will not replace any information contained in ANSUETA-481-2 and 481-3 and is provided for guidance and clarification only. Note: It is the intent of the EIA ACH Committee that this guideline wi

15、ll be rescinded when all of the EIA ACH standards listed under Clause 3 below are revised. 3 Applicable documents This guideline is to be used in accordance with the following ELA ACH standards: a) ANSIEU-481-2, 16mm and 24mm Embossed Carrier Taping of Su#ace Mount Components for Automatic Handling

16、(August 1994) b) ANSIEIA-481-3, 32mm, 44mm, and 56mm Embossed Carrier Taping of Surface Mount Components for Automatic Handling (November 199 i) STD-EIA 784-ENGL 1778 m 3234b00 Ob12231 Obb m Tape A B* C D* N Min. w1 W2 Max. Size Max. Min. Min. See Note 2, Table 1 16.4+2.0 -0.2 24.4+2. O -0.0 16 mm 5

17、0 -0.0 29 37 24 mm 60 13.0+0.5 20.2 609 1.5 EIA-784 Page 2 W3 Min/Max Shall Accommodate Tape Width Without Interference GUIDELINE FOR REEL CONFIGURATION AND DIMENSIONS FOR REEL DIAMETERS LARGER THAN 360mm EDITORIAL ADDITION TO ELA-481-2 (16 mm and 24 mm Carrier Tape) Figure 3a. Reel Configuration fo

18、r A 360 mm. See Section 4.0 for Requirements. All Dimensions in Millimeters. Full Radius, Access Hole at ncludes flange distortion at outer edge) See Note 1 Slot Location w;? (Measured at hub) diameter, see Note 2, f (0 40 mm min.) A. - / (Arbor hol diameter) if present, tape slot in core for tape s

19、tart: 2.5 mm min. width x 10.0 rnrn min. depth B See Note 1 Notes I) Drive spokes optional; if used, dimensions B and D shall apply. 2) Maximum weight of reel and contents 13.6 kg. Table 2a. Reel Dimensions for A 360 mm. See Section 4.0 for Requirements. All Dimensions in Millimeters. Notes 1) For reels less than 360 mm diameter (A), the most widely used reel diameters are 178 mm f 2 mm and 330 mm if used, dimensions B and D shall apply. 2) Maximum weight of reel and contents 13.6 kg.