ECA EIA-364-100A-2012 TP-100A Marking Permanence Test Procedure for Electrical Connectors and Sockets.pdf

《ECA EIA-364-100A-2012 TP-100A Marking Permanence Test Procedure for Electrical Connectors and Sockets.pdf》由会员分享，可在线阅读，更多相关《ECA EIA-364-100A-2012 TP-100A Marking Permanence Test Procedure for Electrical Connectors and Sockets.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD TP-100A Marking Permanence Test Procedure for Electrical Connectors and Sockets EIA-364-100A (Revision of EIA-364-100) November 2012 ANSI/EIA-364-100A-2012 Approved: November 29, 2012 EIA-364-100ANOTICE EIA Engineering Standards and Publications are designed to serve the public interes

2、t through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publication

3、s shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard

4、 is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever

5、to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implications, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA Standard and the IEC document can b

6、e made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitat

7、ions before its use. (From Standards Proposal No. SP-5226.10 formulated under the cognizance of the CE-2.0 National Connector Standards Committee). Published by Electronic Components Industry Association 2012 Engineering Department 2214 Rock Hill Road; Suite 170 Herndon, VA 20170 PLEASE ! DONT VIOLA

8、TE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or ca

9、ll USA and Canada (1-800-854-7179), International (303-397-7956) i CONTENTS Clause Page 1 Introduction . 1 1.1 Scope . 1 1.2 Object 1 1.3 Safety 1 2 Test resources 2 2.1 Equipment . 2 2.2 Material . 2 2.2.1 Class 1 solvent 2 2.2.2 Class 2 solvent 2 2.2.3 Class 3 solvent 3 3 Test specimen 3 3.1 Descr

10、iption 3 4 Test procedure . 3 4.1 Solvent exposure . 3 4.1.1 Class 1 solvent 3 4.1.2 Class 2 solvent 4 4.1.3 Class 3 solvent 4 4.2 Examination 5 5 Details to be specified . 5 6 Test documentation . 5 Table . 1 Solvent classes and description . 1 ii (This page left blank) EIA-364-100A Page 1 TEST PRO

11、CEDURE No. 100A MARKING PERMANENCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS AND SOCKETS (From EIA Standards Proposal No. 5226.10, formulated under the cognizance EIA CE-2.0 Committee on National Connector Standards, and previously published in EIA-364-100.) 1 Introduction 1.1 Scope This standard est

12、ablishes a method of determining the marking permanence of electrical connectors and sockets. 1.2 Object The object of this test procedure is to determine the ability of a connector or socket to withstand solvents that may be used to clean components as well as to determine marking and color code in

13、tegrity. Table 1 - Solvent classes and description Classes Description 1 Alcohol and mineral spirits; see 2.2.1 2 Terpene defluxer; see 2.2.2 3 Water, propylene glycol monoethanolamine, and monoethanolamine; see 2.2.3 1.3 Safety The solvents listed in 2.2 exhibit some potential for health and safety

14、 hazards, and the following safety precautions shall be observed. 1.3.1 Avoid contact with eyes. Chemical goggles shall be worn while performing test. 1.3.2 Avoid prolonged contact with skin. 1.3.3 Perform all work in a laboratory fume hood, or provide adequate ventilation. EIA-364-100A Page 2 1.3.4

15、 It is recommended that the solutions be heated in an explosion-proof laboratory hood. Do not use open flame. Hot plate may also be used. NOTE Refer to the manufacturers material safety data sheets for emergency first aid procedures. 2 Test resources 2.1 Equipment 2.1.1 Basket: Stainless steel mesh

16、basket of sufficient size. 2.1.2 Brush: Toothbrush made of materials that are nonreactive with the solvent being used. Brush shall have three long rows of hard bristles, whose free ends shall be substantially in the same horizontal plane. The brush shall be discarded at the completion of the test. 2

17、.1.3 Vessel: Heat-resistant beaker or vapor degreaser made of nonreactive material and of sufficient size to hold the basket. 2.1.4 Laboratory fume hood. 2.1.5 Explosion-proof heat chamber, or hot plate. 2.2 Material All organic solvents shall be American Chemical Society technical grade or better.

18、2.2.1 Class 1 solvent A mixture consisting of the following: 2.2.1.1 One part by volume isopropyl alcohol. 2.2.1.2 Three parts by volume mineral spirits, or three parts by volume of a mixture of 80% by volume of kerosene and 20% by volume ethylbenzene. 2.2.2 Class 2 solvent A terpene defluxer consis

19、ting of a surfactant containing at least 90% d-limonene. EIA-364-100A Page 3 2.2.3 Class 3 solvent A mixture consisting of the following: 2.2.3.1 Forty-two parts by volume water, 1 megaohm-centimeter minimum resistivity. 2.2.3.2 One part by volume of propylene glycol monomethyl ether (glycol ether P

20、M, 1-methoxy-2-propanol). 2.2.3.3 One part by volume of monoethanolamine. 3 Test specimen 3.1 Description A separate specimen from the same lot shall not be exposed and serve as a reference. All specimens and marking shall be visually inspected prior to testing. 4 Test procedure 4.1 Solvent exposure

21、 The specimens shall be subjected to the solvent class(es) specified by the referencing document as selected from Table 1. An individual specimen shall not be subjected to multiple solvent classes, unless otherwise specified in the referencing document. 4.1.1 Class 1 solvent 4.1.1.1 The solution sha

22、ll be maintained at a temperature of 25 C 5 C. The specimens shall be placed in a wire basket and completely immersed for 3 minutes + 0.5 minute, - 0 minute in the solution specified in 2.2.1. 4.1.1.2 Dip the bristle portion of the brush in the solution until wetted, then remove the specimen from th

23、e solution and immediately brush the specimen with normal hand pressure (approximately 0.56 Newton to 0.83 Newton (2 ounces-force to 3 ounces-force ) applied normal to the surface) for five strokes in both the forward and reverse direction on the portion of the specimen where marking has been applie

24、d. 4.1.1.3 Immediately after brushing, the procedure shall be repeated two more times, for a total of three immersions, followed by brushing. 4.1.1.4 After completion of the third immersion and brushing, the specimens shall be air blown dry. EIA-364-100A Page 4 4.1.1.5 The specimens shall be inspect

25、ed in accordance with 4.2 to determine the extent, if any, of deterioration that has occurred. 4.1.2 Class 2 solvent 4.1.2.1 The solution shall be maintained at a temperature of 25 C 5 C. The specimens shall be placed in a wire basket and completely immersed for 3 minutes + 0.5, - 0 minutes in the s

26、olution specified in 2.2.2. 4.1.2.2 Dip the bristle portion of the brush in the solution until wetted, then remove the specimen from the solution and immediately brush the specimen with normal hand pressure (approximately 0.56 Newton to 0.83 Newton (2 ounces-force to 3 ounces-force ) applied normal

27、to the surface) for five strokes in both the forward and reverse direction on the portion of the specimen where marking has been applied. 4.1.2.3 Immediately after brushing, the procedure shall be repeated two more times, for a total of three immersions, followed by brushing. 4.1.2.4 After completio

28、n of the third immersion and brushing, the specimens shall be rinsed in approximately 25 C water and all surfaces air blown dry. 4.1.2.5 The specimens shall be inspected in accordance with 4.2 to determine the extent, if any, of deterioration that has occurred. 4.1.3 Class 3 solvent 4.1.3.1 The solu

29、tion shall be maintained at a temperature of 63 C to 70 C. The specimens shall be placed in a wire basket and completely immersed for 3 minutes + 0.5, - 0 minute in the solution specified in 2.2.3. 4.1.3.2 Dip the bristle portion of the brush in the solution until wetted, then remove the specimen fr

30、om the solution and immediately brush the specimen with normal hand pressure (approximately 0.56 Newton to 0.83 Newton (2 ounces-force to 3 ounces-force ) applied normal to the surface) for five strokes in both the forward and reverse direction on the portion of the specimen where marking has been a

31、pplied. 4.1.3.3 Immediately after brushing, the procedure shall be repeated two more times, for a total of three immersions, followed by brushing. 4.1.3.4 After completion of the third immersion and brushing, the specimens shall be rinsed in approximately 25 C water and all surfaces air blown dry. 4

32、.1.3.5 The specimens shall be inspected in accordance with 4.2 to determine the extent, if any, of deterioration that has occurred. EIA-364-100A Page 5 4.2 Examination After subjection to the test, any specified markings that are missing in whole or in part, faded, smeared, blurred, or shifted (disl

33、odged) to the extent that they cannot be readily identified from a distance of at least 152 millimeters (6 inches) with normal room lighting without the aid of magnification or with a viewer having a magnification no greater than 3X shall constitute failure. 5 Details to be specified The following d

34、etails shall be specified in the referencing document: 5.1 Solvent class(es) 5.2 Number of specimens to be tested for each class 5.3 The extent of deterioration of the marking or color code 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and t

35、he following: 6.1 Title of test 6.2 Specimen description and specimen size 6.3 Results including defects and location 6.4 Name of operator and start/finish date(s) of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, heal

36、th or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 170 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone

37、No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forward

38、ed to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions A SP-5226.10 Revised paragraphs 4.1, 5 and 6.4 Electronic Components Industry Association 2214 Rock Hill Road, Suite 170 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.eciaonline.org