DOD A-A-51832-1987 BANDAGE ADHESIVE《带粘性的绷带》.pdf

《DOD A-A-51832-1987 BANDAGE ADHESIVE《带粘性的绷带》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-51832-1987 BANDAGE ADHESIVE《带粘性的绷带》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-51832 65 m 7777774 0028530 7 m COMM ERCI AL J. TEM DESCRI PTION a c $6s=/a A-A-5183 2 13 May 1YS7 Inches -by 3 1 by 3 BANDAGE, ADHESIVE The General Services Administration has authorized the use of this Commercial Item Descriptj.on in preference to (Size 3/4 by 3 inches) and (Size 1 by 3 inches)

2、 Bandage of Interim Federal Specification DUD-B-0035C (GSA-FSS) dated 30 December 1971 This Commercial Item Description covers a. sterile adhesive bandage, suitable for use on minor abrasions, cuts or wounds. Salient Characteristics: The bandage shall be a sterile individual bandage, sujtable Cor us

3、e on minor abrasions, cuts or wounds. The adhesive strip shall be a plastic film, noniinally 3 inches Jong, flesh colored or clear. The a.dhecive strip ska3.1 be perforated where the compress is attached, with perforations of the same size, frequency and spacing pattern; the remainder of tire adhesi

4、ve strip may be similarly perforated. The corners or ends of the adhesive strip shall be rounded. The adhesive strip shall have a minimum breaking strength of 3.5 pounds per inch after perforating, when teated in accordance with Federal Test Method Standard No. 19J., Method 5102, except the specimen

5、 shall be the adhesive bandage full length with the facing material peeled off. The adhesive strip when applied to the skin shall adhere firmly. The size of each bandage and its compress shall be as specified in Table I, with the additional requirements that the conpress shall be centrally affixed t

6、o the bandage adhesive strip arid shall not. overhang the edges of the strip. Table I Bandage Bandage Compress. Nominal Size Minimum Dimensions-Inches Minimum Dimension-Inches Width 15/16 L1J16 Lenqth Size 7/t3 1 2-27/32 13/16 7/8 2 FSC 6510 DISTRIBUTION STATEMENT A. Approved for public release, dis

7、tribution is unlimited. THIS DOCUMENT CONTAINS 5 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-51 83 2 Mien used with a clear aheeive &trip, the strip side layer of the campress ahaJ1 be flesh colored, The compress shaJ.1 be appasximatel

8、y equivalent ta, but not less than, the absorbency and wejyh of a compram of the came size made of four layers OE Absorbent Gauze, USP, Type I, shall be free from loose threads OK savelings, shall be nontoxic and shall be inso3uble in the wound. The top layer of each compwess shall be either Type 1

9、Abscsrbent: Gauze, UCP, 01: shall be absorbent gauze wjth 40 warp and 32 fill, i/- 3 threads per inch, which meets a19 of the tequirementa of Absorbent Gauze, USP, except for: weight onil thread eaunt, or shal3 be a suitable film cover which is enooth and non-adherent to the wound and which shall pe

10、rmlt the wound exudates to be readily transmitted to and absorbed Th adhetshe bandage shall be covered with two-piece facing material in euch a manner as to completely cover the compress and avetlap each other by a minimum of 1/8 inch (0.32 crn) at the approximate center of the compress. The facing

11、material shall be capable of being easily removed without contaminating the compress, OK breaking, or cracking, and shall be chemically inert to the adhesive mass. lay the COMKSS Ehen testing or sterility, shall be in accordance with the nterility testing method specfied in the U.S.P, Korkmanship. T

12、he bandage shall be free from defects which detract: rom its appearance or impair its serviceability. - Unit. Box (BX). Each adhesive bandage shall be individually packaged in an envelope capable of maintaining sterility o contents unlem package is damaged or opened. The envelope shall permit easy r

13、emoval o the sterile adhesive bandage. One box containing 100 individually packaged adhesive bandagesr as specified, constitutes one unit. Contractor certification. The contractor shall certify that the product offered meets the salient characteristics o thi& description and conforms to the producer

14、s own drawings, specifications, standards, and c-uality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract, 2 Provided by IHSNot for ResaleNo reproduc

15、tion or networking permitted without license from IHS-,-,-A-A-51832 65 m 777777L1 0028532 2 m A-A-51 832 Quality Assurance Provisions. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requ

16、irements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own OL any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to per

17、form any of the inspections set forth in the specification where such inspections are deensecl necessary to assure supplies and services conform to prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and nade av

18、ailable to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as used herein, is defined as both examination (such

19、as visual or auditory investigation w thout the use of special laboratory appliances or procedures) and testing (deteiminatian by technical means of physical and chemica properties) of the item. Testing and examination shall be conducted to determine compliance with all specif icatj.or-i requirement

20、s. Test methods shall be suitable, accurate, and reproducible. Samplinq for examination. Sampling for examination shall be conducted in accordance with MIL-STD-105 and as specified herein. The unit of product for examination shall beone adhesive bandage. Unless otherwise specified, sampling for exam

21、ination shall be conducted at inspection level II, AQL 2.5 maximum percent defective. will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerances specified using conversion tables contained in the latest revision of Federal Standard

22、No. 376, and all other requirements of this document are met. Metric Products - Products manufactured to metric dimensions If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting offic

23、er to determine if the product is acceptable. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-SZB32 65 D qqq974 0028533 Y A-A-FI 832 The contracting officer has the option of accepting or rejecting the pLaduct , RequJ awry reqiui rements , Fede

24、ral Food, Druq and Cosmetic Act, If the product: Covered by this dor:unimt has been deterniined by the U.S. Food and Drus - Aaminietratien CJ be under its jurisdiction, the oferor/contrnctsr shall comply, and be responsible for compliance by its subcontracors/suppliers, with the requirement& of the

25、Federal Food, Drug and Cosmetic Act, as amended, and regulations peomugated thereunder , In addition, the offeror/csntrnctor shall comply, and be responsib3e for compliance by its subcontracars/suppliers, with the requirements a% all other applicable Federal, State, and local statutes, ordinances, a

26、nd rgulations, Recovered materials. The offeror/contractor i8 encouraged to uee teesvere6 material in accordance with Public Law 94-580, as trmsned, and as implemented by Fedeilal Acquisition Regulation Subpart 23,4 to the maximum extent practical, meervation , packaging, p acking, labeling, and mak

27、ing. Unless otherwise specified, preservation, packaging, and packing shall be to a degree o protection to pceclude damage to containers and/or contents thereof under norma shipping conditions, kandllfny, etc., involving shipment from the supply source to the receiving activity, plus reshjpment from

28、 receiving activity, and chail conform to applicable carriers rules and regulations. Intermediate and exterioc package quantities and 1-abeling and maPking sha1.I be as specified in the contract and/or order, NOTE: The following National Stock Numbers are covered by this document : - MSN ITEM IDENTI

29、FICATION 6510-60-597-7469 BANDAGE, ADHESIVE, 3/4 by 3 inches, 100s BANDAGE ADHESIVE i inch by 3 inches, 100s 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b. A-A-5L32 65 m 9977774 0026534 b m A-A-51 fi32 Ordering data. (The inspecti.on/tect datin

30、g period, intermediate/exterior quantities, labeling, and marking must be as specified in the contract and/or order). MILITARY 1NTERESTS:Freparing Activity: Custodians: DoD-MB Army - MD Agent: Navy- MS Air Force - 03 DLA-DM CIVIL AGENCY COORDINATING ACTIVITY: VA-OSS PHS FDA-MPQAS PGC 05203 Project No. 6510-0727 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-