DLA SMD-5962-99569 REV C-2007 MICROCIRCUIT MEMORY DIGITAL CMOS FIELD PROGRAMMABLE GATE ARRAY 16 000 GATES MONOLITHIC SILICON《微型电路 带记忆力 数字型 CMOS 现场可编程门阵列 16000门 单块硅》.pdf

《DLA SMD-5962-99569 REV C-2007 MICROCIRCUIT MEMORY DIGITAL CMOS FIELD PROGRAMMABLE GATE ARRAY 16 000 GATES MONOLITHIC SILICON《微型电路 带记忆力 数字型 CMOS 现场可编程门阵列 16000门 单块硅》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-99569 REV C-2007 MICROCIRCUIT MEMORY DIGITAL CMOS FIELD PROGRAMMABLE GATE ARRAY 16 000 GATES MONOLITHIC SILICON《微型电路 带记忆力 数字型 CMOS 现场可编程门阵列 16000门 单块硅》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added devices 03 and 04, editorial changes to table I and the appropriate paragraphs throughout the document. Added figures for bond pad locations for device 03. ksr 99-11-10 Raymond Monnin B Update input leakage current in Table I for device 01

2、and 02. Updated boilerplate references. Updated notes on Case X and Y ksr 01-03-12 Raymond Monnin C Boilerplate update, part of 5 year review. ksr 07-07-24 Robert M. Heber REV SHET REV C C C C C C C C C C C C C C SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 REV STATUS REV C C C C C C C C C C C C

3、C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Kenneth Rice DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Jeff Bowling COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin

4、 AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99 - 07 -01 MICROCIRCUIT, MEMORY, DIGITAL, CMOS, FIELD PROGRAMMABLE GATE ARRAY, 16,000 GATES, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-99569 SHEET 1 OF 28 DSCC FORM 2233 APR 97 5962-E502-07 Provided by I

5、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99569 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assuranc

6、e class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels ar

7、e reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 99569 01 Q X C | | | | | | | | | | | | Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Draw

8、ing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA

9、 designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Bin Speed 01 RT54SX16 16,000 gate field programmable gate array 86 ns 02 RT54SX16-1 16,000 gate field programmable gate a

10、rray 73 ns 03 A54SX16 16,000 gate field programmable gate array 40 ns 04 A54SX16-1 16,000 gate field programmable gate array 34 ns 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements docume

11、ntation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and

12、 as follows: Outline letter Descriptive designator Terminals Package style X See Figure 1 256 Ceramic Quad Flat Pack Y See Figure 1 208 Ceramic Quad Flat Pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class

13、M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99569 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 3.3 V DC suppl

14、y voltage range (VCCA, and VCCI).-0.3 V dc to +4.0 V dc 5.0 V DC supply voltage range (VCCR) .-0.3 V dc to +6.0 V dc Input voltage range (VI) .-0.5 V dc to +5.5 V dc Output voltage range (VO) .-0.5 V dc to +3.6 V dc I/O source sink current (IIO) .-30 to +5.0 mA Storage temperature range (TSTG).-40C

15、to +125C Lead temperature (soldering, 10 seconds) 300C Thermal resistance, junction-to-case (JC): Case X.8C/W 2/ Case Y.9C/W 2/ Maximum junction temperature (TJ).+150C 1.4 Recommended operating conditions. 3.3V Power supply (VCCA, and VCCI) +3.0 V dc to +3.6 V dc (10% VCC) 5.0V Power supply (VCCR)+4

16、.5 V dc to +5.5 V dc (10% VCC) Case operating temperature range (TC) -55C to +125C 1.5 Digital logic testing for device classes Q and V. Fault coverage measurement of manufacturing logic tests (MIL-STD-883, test method 5012) 100 percent 3/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standa

17、rds, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integra

18、ted Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-H

19、DBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil from the Standardization Document Order Desk, 700 Robins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications

20、. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM Standard F1192-00 - Standard Guide for the Measurement of Sin

21、gle Event Phenomena from Heavy Ion Irradiation of Semiconductor Devices. (Applications for copies of ASTM publications should be addressed to: ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; http:/www.astm.org.) 1/ Stresses above the absolute maximum rating

22、may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ When the thermal resistance for this case is specified in MIL-STD-1835, that value shall supersede the value indicated herein. 3/ 100 percent test coverage of blank p

23、rogrammable logic devices. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99569 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 ELECTRONICS INDUSTRIES

24、ASSOCIATION (EIA) JEDEC Standard EIA/JESD78 - IC Latch-Up Test. (Applications for copies should be addressed to the Electronics Industries Association, 2500 Wilson Boulevard, Arlington, VA 22201; http:/www.jedec.org.) (Non-Government standards and other publications are normally available from the o

25、rganizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes

26、precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herei

27、n or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class leve

28、l B devices and as specified herein. 3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device cl

29、asses Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). 3.2.3.1 Unprogramm

30、ed devices. The truth table or test vectors for unprogrammed devices for contracts involving no altered item drawing is not part of this drawing. When required in screening (see 4.2 herein) or quality conformance inspection group A, B, C, D, or E (see 4.4 herein), the devices shall be programmed by

31、the manufacturer prior to test. A minimum of 50 percent of the total number of logic modules shall be utilized or at least 25 percent of the total logic modules shall be utilized for any altered item drawing pattern. 3.2.3.2 Programmed devices. The truth table or test vectors for programmed devices

32、shall be as specified by an attached altered item drawing. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply o

33、ver the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In

34、addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked.

35、 Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535

36、. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see

37、6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this

38、drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

39、om IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99569 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class

40、M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any c

41、hange that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at t

42、he option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 42 (see MIL-PRF-38535, appendix A). 3.11 Processing options. Since the device is capable of being programmed by either the manufactur

43、er or the user to result in a wide variety of configurations, two processing options are provided for selection in the contract. 3.11.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.3.1 and table IIA. It is recommended that users p

44、erform subgroups 7 and 9 after programming to verify the specific program configuration. 3.11.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions herein, including the requirements of the altered item drawing, shall be satisfied by the ma

45、nufacturer prior to delivery. 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affec

46、t the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior

47、to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Delete the sequence specified

48、as initial (pre-burn-in) electrical parameters through interim (post-burn-in) electrical parameters of method 5004 and substitute lines 1 through 6 of table IIA herein. b. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. For device class M the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015. (1) D