DLA SMD-5962-96852 REV B-2007 MICROCIRCUIT HYBRID LINEAR SINGLE CHANNEL OPTICALLY COUPLED POWER TRANSISTOR INTERFACE《单通道功率耦联晶体管接口混合线型微电路》.pdf

《DLA SMD-5962-96852 REV B-2007 MICROCIRCUIT HYBRID LINEAR SINGLE CHANNEL OPTICALLY COUPLED POWER TRANSISTOR INTERFACE《单通道功率耦联晶体管接口混合线型微电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-96852 REV B-2007 MICROCIRCUIT HYBRID LINEAR SINGLE CHANNEL OPTICALLY COUPLED POWER TRANSISTOR INTERFACE《单通道功率耦联晶体管接口混合线型微电路》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing boilerplate. 02-09-06 Raymond Monnin B Update drawing. -gz 07-02-05 Joseph Rodenbeck REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve L. Duncan DEFENSE SUPPLY CE

2、NTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael Jones POST OFFICE BOX 3990 COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, SINGLE CHANNEL, OPTICALLY COUPLED POWER TRANS

3、ISTOR INTERFACE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-12-16 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-96852 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E232-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN

4、DARD MICROCIRCUIT DRAWING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and

5、 lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 96852 01 H P X Federal RHA Device Device Case Le

6、ad stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels an

7、d shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function 01 HCPL-5301 Power transistor interface, single channel 1.2.3 Device clas

8、s designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance le

9、vels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are require

10、d. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspectio

11、ns (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensu

12、re that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) shall be as d

13、esignated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P CDIP2-T8 8 Dual-in-line X See figure 1 8 Dual-in-line Y See figure 1 8 Dual-in-line Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC

14、ROCIRCUIT DRAWING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Storage temperature range -65C to +150C Junction tem

15、perature (TJ) +175C Average input current (IF(AVG) +25 mA Peak input current (50% duty cycle, 1 ms pulse width (IF(PEAK) +50 mA Peak transient input current ( 3.0 V, VCM= 1000 VP-P, TA= +25C 9 01 10 kV/s Output low level common mode transient immunity 11/ 12/ CML VCC= 15.0 V, IF= 10 mA, CL= 100 pF,

16、VO3.0 V). 11/ Parameters are tested as part of device initial characterization and after design and process changes. Parameters shall be guaranteed to the limits specified in table I for all lots not specifically tested. 12/ Common mode transient immunity in a logic low level is the maximum tolerabl

17、e dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a logic low state (i.e., VO 1.0 V). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUM

18、BUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbol Min Max Min Max A 4.57 .180 A1 1.40 1.65 .055 .065 b 0.41 0.51 .016 .020 c 0.18 0.33 .007 .013 D 9.40 9.91 .370 .390 e 2.29 2.79 .090 .110 E 9.65 9.91 .380 .390 E1 8.13 .320 L 1.07 1.32 .042

19、 .052 S 0.89 1.27 .035 .050 Case outline Y. Millimeters Inches Symbol Min Max Min Max A 4.32 .170 A1 1.14 1.40 .045 .055 b 0.41 0.51 .016 .020 c 0.18 0.33 .007 .013 D 9.40 9.91 .370 .390 e 2.29 2.79 .090 .110 E 8.13 .320 eA 7.37 7.87 .290 .310 Q 0.51 .020 S 0.89 1.27 .035 .050 NOTES: 1. The U.S. gov

20、ernment preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is indicated by the ESD triangle. FIGURE 1. Case outline(

21、s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines P, X, and Y Termi

22、nal number Terminal symbol 1 2 3 4 5 6 7 8 NC +VF1(anode) -VF1(cathode) NC GND VO1RINTVCCFIGURE 2. Terminal connections. 12348765FIGURE 3. Switching test circuit and waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA

23、WING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1 Fina

24、l electrical parameters 1*,2,3,9,10,11 Group A test requirements 1,2,3,9,10,11 Group C end-point electrical parameters 1,2,3 End-point electrical parameters for radiation hardness assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.3 Conformance and periodic inspections. Conformanc

25、e inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, an

26、d 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein.

27、b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall s

28、pecify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-

29、883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

30、 IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96852 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended u

31、se. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepare

32、d specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated as specified in MIL-PRF-38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configurati

33、on control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on t

34、his drawing should be directed to DSCC-VA, Post Office Box 3990, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see

35、 3.7 herein) to DSCC-VA and have agreed to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 07-02-05 Approved sources of supply for SMD 5962-96852 are listed below for immediate acquisition in

36、formation only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepte

37、d by DSCC-VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DSCC maintains an online database of all current sources of supply at http:/www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/

38、5962-9685201HPC 5962-9685201HPA 50434 50434 HCPL-5301 HCPL-5301#200 5962-9685201HXA 50434 HCPL-5301#300 5962-9685201HYC 5962-9685201HYA 50434 50434 HCPL-5301#100 HCPL-5301#100 5962-9685201KPC 5962-9685201KPA 50434 50434 HCPL-530K HCPL-530K#200 1/ The lead finish shown for each PIN representing a her

39、metic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance re

40、quirements of this drawing. Vendor CAGE Vendor name number and address 50434 Avago Technologies 350 West Trimble Road San Jose, CA 95131 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-