DLA SMD-5962-96517 REV F-2012 MICROCIRCUIT DIGITAL ADVANCED CMOS RADIATION HARDENED HEX INVERTER TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf

《DLA SMD-5962-96517 REV F-2012 MICROCIRCUIT DIGITAL ADVANCED CMOS RADIATION HARDENED HEX INVERTER TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-96517 REV F-2012 MICROCIRCUIT DIGITAL ADVANCED CMOS RADIATION HARDENED HEX INVERTER TTL COMPATIBLE INPUTS MONOLITHIC SILICON.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R074-97. - jak 96-11-25 Monica L. Poelking B Incorporate NOR and update boilerplate to latest MIL-PRF-38535 requirements. - CFS 01-06-11 Thomas M. Hess C Correct outputs in figure 2. Update boilerplate to lates

2、t MIL-PRF-38535 requirements. - CFS 05-06-24 Thomas M. Hess D Add ASTM guideline in 2.2. Correct voltage level testing in switching waveforms and test circuit, figure 4. Updated RHA testing paragraphs in 4.4.4.1 - 4.4.4.4. Add appendix A. - PHN 07-07-24 Thomas M. Hess E Add device types 02 and 03. U

3、pdate radiation hardness assurance paragraphs. Add table IB. - jak 10-11-16 Muhammad A. Akbar F Add equivalent test circuit and footnote 5 in figure 4. - MAA 12-04-19 Thomas M. Hess REV SHEET REV F F F F F F F F F F SHEET 15 16 17 18 19 20 21 22 23 24 REV STATUS REV F F F F F F F F F F F F F F OF SH

4、EETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelk

5、ing MICROCIRCUIT, DIGITAL, ADVANCED CMOS, RADIATION HARDENED, HEX INVERTER, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-04-19 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-96517 SHEET 1 OF 24 DSCC FORM 2233 APR 97 5962-E288-12

6、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96517 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assu

7、rance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) level

8、s is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 H 96517 01 V X C Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA

9、designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (

10、-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACTS04 Radiation hardened, hex inverter, TTL compatible inputs 02 54ACTS04E Enhanced, radiation hardened, hex inverter, TTL compatible in

11、puts 03 54ACTS04E Enhanced, radiation hardened, hex inverter, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requ

12、irements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designa

13、tor Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line X CDFP3-F14 14 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking per

14、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96517 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VDD) -0.3 V dc to +7.0 V dc DC input voltage range, any pin

15、(VIN) . -0.3 V dc to VDD+ 0.3 V dc DC output voltage range, any pin (VOUT) -0.3 V dc to VDD+ 0.3 V dc DC input current, any one input (IIN) . 10 mA Latch-up immunity current (ILU) 150 mA Storage temperature range (TSTG) -65C to +150C Lead temperature (soldering, 5 seconds) . +300C Thermal resistance

16、, junction-to-case (JC): Case outline C and X, device type 01 See MIL-STD-1835 Case outline X, device types 02 and 03 . 15.5C/W Junction temperature (TJ) . +175C Maximum package power dissipation (PD): Device type 01 . 1.0 W Device types 02 and 03 3.2 W 4/ 1.4 Recommended operating conditions. 2/ 3/

17、 Supply voltage range (VDD): Device type 01 . +4.5 V dc to +5.5 V dc Device types 02 and 03 +3.0 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VDDOutput voltage range (VOUT) . +0.0 V dc to VDDCase operating temperature range (TC) . -55C to +125C Maximum input rise and fall time at VDD= 4.

18、5 V (tr, tf) 1 ns/V 5/ 1.5 Radiation features. 6/ Maximum total dose available: Device type 01 (dose rate = 50 300 rads (Si)/s) . 1 x 106rads (Si) 7/ Device type 02 (effective dose rate = 1 rad (Si)/s) 1 x 106rads (Si) 8/ Device type 03 (dose rate = 50 300 rads (Si)/s) . 5 x 105rads (Si) 7/ Single e

19、vent phenomenon (SEP): Device type 01: Effective LET, no SEU (see 4.4.4.4) 80 MeV-cm2/mg 9/ Effective LET, no SEL (see 4.4.4.4) . 120 MeV-cm2/mg 9/ Device types 02 and 03: Effective LET, no SEU (see 4.4.4.4) 108 MeV-cm2/mg 9/ Effective LET, no SEL (see 4.4.4.4) . 120 MeV-cm2/mg 9/ Dose rate upset (2

20、0 ns pulse) . 1 x 109 rads (Si)/s 9/ 10/ Dose rate induced latch-up None 9/ Dose rate survivability 1 x 1012 rads (Si)/s 9/ _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliabilit

21、y. 2/ Unless otherwise specified, all voltages are referenced to VSS.3/ The limits for the parameters specified herein shall apply over the full specified VDDrange and case temperature range of -55C to +125C unless otherwise specified. 4/ Per MIL-STD-883 method 1012.1 section 3.4.1, PD(Package) = (T

22、J (max) - TC(max). JC5/ Derate system propagation delays by difference in rise time to switch point for tror tf 1 ns/V. 6/ Radiation testing is performed on the standard evaluation circuit (SEC). 7/ Device types 01 and 03 are tested in accordance with MIL-STD-883,method 1019, condition A. 8/ Device

23、type 02 is irradiated at dose rate = 50 - 300 rads (Si)/s in accordance with MIL-STD-883, method 1019, condition A, and is guaranteed to a maximum total dose specified. The effective dose rate after extended room temperature anneal = 1 rad (Si)/s per MIL-STD-883, method 1019, condition A, section 3.

24、11.2. The total dose specification for these devices only applies to a low dose rate environment. 9/ Limits are guaranteed by design or process, but not production tested unless specified by the customer through the purchase order or contract. 10/ This limit is applicable for device type 01, 02, and

25、 03 with VDD 4.5 V. Device types 02 and 03 do not meet this limit at VDD 4.5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96517 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 D

26、SCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the soli

27、citation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT

28、OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Phila

29、delphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation or contract. ASTM INTERNATIONAL (ASTM) AS

30、TM F1192 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion Irradiation of Semiconductor Devices. (Copies of these documents are available online at http:/www.astm.org or from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA, 1942

31、8-2959). 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. RE

32、QUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or

33、function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shal

34、l be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1

35、. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. Provided by IHSNot for ResaleNo re

36、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96517 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 3.2.6 Irradiation test connections. The irradiation test connections shall be maintained by t

37、he manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and p

38、ostirradiation parameter limits are as specified in table IA and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I

39、A. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the devic

40、e. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark

41、for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 l

42、isted manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance

43、submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and

44、 herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M.

45、For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, and DLA Land

46、 and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M

47、devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96517 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990

48、REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics. Test Symbol Test conditions 1/ 2/ -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Limits 3/ Unit Min Max Low level input voltage VIL02, 03 3.0 V and 3.6 V 1, 2, 3 0.8 V All 4.5 V and 5.5 V 1, 2, 3 0.8 V High level input voltage VIH02, 03 3.0 V and 3.6 V 1, 2, 3 2.0 V All 4.5 V and 5.5 V 1, 2, 3 0.5VDDV High level output voltage VOH For all inputs affecting output under test VIN= VDDor VSSIOH= -6.0 mA 02, 03 3.0 V and 3.6 V 1, 2, 3 2.4 V For all inputs affecting output