DLA SMD-5962-95525 REV A-2013 MICROCIRCUIT DIGITAL CMOS QUAD ELECTRICALLY ERASABLE PROGRAMMABLE POTENTIOMETER MONOLITHIC SILICON.pdf

《DLA SMD-5962-95525 REV A-2013 MICROCIRCUIT DIGITAL CMOS QUAD ELECTRICALLY ERASABLE PROGRAMMABLE POTENTIOMETER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-95525 REV A-2013 MICROCIRCUIT DIGITAL CMOS QUAD ELECTRICALLY ERASABLE PROGRAMMABLE POTENTIOMETER MONOLITHIC SILICON.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect current MIL-PRF-38535 requirements. glg 13-02-21 Charles Saffle REV SHEET REV A A A A A A SHEET 15 16 17 18 19 20 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPA

2、RED BY Gary L. Gross DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Jeff Bowling COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William J. Johnson MICROCIRCUIT, DIGITAL, CMOS, QUAD ELECTRICALLY ERASABLE PRO

3、GRAMMABLE POTENTIOMETER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 95-02-10 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-95525 SHEET 1 OF 20 DSCC FORM 2233 APR 97 5962-E268-13 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

4、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95525 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M)

5、 and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following

6、example: 5962 - 95525 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38

7、535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) i

8、dentify the circuit function as follows: Potentiometer Organization (ohms) Endurance (writes Device type Generic number 1/ Circuit function Pot 0 Pot 1 Pot 2 Pot 3 per register 01 9241Y Quad EEPOT 2.0 K 2.0 K 2.0 K 2.0 K 100,000 02 9241W Quad EEPOT 10 K 10 K 10 K 10 K 100,000 03 9241U Quad EEPOT 50

9、K 50 K 50 K 50 K 100,000 04 9241M Quad EEPOT 2.0 K 10 K 10 K 50 K 100,000 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements f

10、or MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Termin

11、als Package style R GDIP1-T20 20 dual in-line package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1/ Generic numbers are also listed in the Standard Microcircuit Drawing Source Approval Bulletin and i

12、n MIL-HDBK-103 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95525 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 2/ Supply volt

13、age range with respect to ground (VCC) . -1.0 V dc to +7.0 V dc Voltage SCL, SDA, or A0 A3 with respect to ground . -1.0 V dc to +7.0 V dc Voltage on any VHor VLpin referenced to ground +8.0 V dc Differential voltage (V = VH- VL) . 16 V dc Storage temperature range (TSTG) -65C to +150C Maximum power

14、 dissipation (PD) 225 mW Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +175C 3/ Thermal resistance, junction-to-case (JC): See MIL-STD-1835 Data retention . 100 years minimum Endurance (all device types) . 100,000 writes per register (minimum) 1.4 Recommended operating

15、 conditions. Supply voltage range (VCC) . 4.5 V dc to 5.5 V dc Case operating temperature range (TC) -55C to +125C Low level input voltage range (VIL) -0.1 V dc to 0.8 V dc High level input voltage range (VIH) . 2.0 V dc to VCC+ 1.0 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standard

16、s, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrate

17、d Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDB

18、K-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form

19、a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation. _ 2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum level

20、s may degrade performance and affect reliability. 3/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

21、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95525 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 JEDEC INTERNATIONAL (JEDEC) JESD 78 - IC Latch-Up Test. (Applications for copies should be addressed to the Electronics Industries Alliance, 25

22、00 Wilson Boulevard, Arlington, VA 22201; http:/www.jedec.org.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3

23、 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3

24、.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as

25、described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as spec

26、ified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Tr

27、uth table. The truth table shall be as specified on figure 2. 3.2.4 Switching test circuit and waveforms. The radiation exposure circuit shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electric

28、al performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for

29、each subgroup are defined in table IA. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of

30、not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/comp

31、liance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance

32、shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 her

33、ein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requireme

34、nts of MIL-PRF-38535, appendix A and herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95525 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.7 Certificat

35、e of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, not

36、ification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and th

37、e acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawi

38、ng shall be in microcircuit group number 42 (see MIL-PRF-38535, appendix A). 3.11 Processing of EEPOTs: All testing requirements and quality assurance provisions herein shall be satisfied by the manufacturer prior to delivery. 3.11.1 Conditions of the supplied devices: Devices will be supplied in un

39、programmed or cleared state. No provision will be made for supplying written devices. 3.11.2 Erasure of EEPOTs: When specified, devices shall be cleared in accordance with the procedures and characteristics specified in 4.5.1. 3.11.3 Programming of EEPOTs: When specified, devices shall be written in

40、 accordance with the procedures and characteristics specified in 4.5.2. 3.11.4 Verification of state of EEPOTs: When specified, devices shall be verified as either written to the specified pattern or cleared. As a minimum, verification shall consist of performing a read of the entire array to verify

41、 that all bits are in the proper state. Any bit that does not verify to be in the proper state shall constitute a device failure and the device shall be removed from the lot or sample. 3.12 Data retention. A data retention stress test shall be completed as part of the vendors reliability monitors. T

42、his test shall be done for initial characterization and after any design or process changes which may affect data retention. The methods and procedures may be vendor specific but shall guarantee data retention listed in section 1.3 herein over the full military temperature range. The vendors procedu

43、re shall be kept under document control and shall be made available upon request of the acquiring or preparing activity, along with test data. 3.13 Endurance. A reprogrammability test shall be completed as part of the vendors reliability monitors. This reprogrammability test shall be done for initia

44、l characterization and after any design or process changes which may affect the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of program/erase endurance cycles listed in section 1.3 herein over the full military temperature range.

45、The vendors procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity, along with test data. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596

46、2-95525 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Qual

47、ity Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in ac

48、cordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Delete the sequence specified as initial (preburn-in) electrical parameters through interim (postburn-in) electrical parameters of method 5004 and substitute lines 1 through 6 of table IIA herein. b. Prior to burn-in, the devices shall be program