DLA SMD-5962-94708 REV B-2008 MICROCIRCUIT LINEAR DUAL WIDEBAND LOW NOISE VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER MONOLITHIC SILICON《微电路 线性电压反馈宽带宽低噪单片二运算放大器》.pdf

《DLA SMD-5962-94708 REV B-2008 MICROCIRCUIT LINEAR DUAL WIDEBAND LOW NOISE VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER MONOLITHIC SILICON《微电路 线性电压反馈宽带宽低噪单片二运算放大器》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-94708 REV B-2008 MICROCIRCUIT LINEAR DUAL WIDEBAND LOW NOISE VOLTAGE FEEDBACK OPERATIONAL AMPLIFIER MONOLITHIC SILICON《微电路 线性电压反馈宽带宽低噪单片二运算放大器》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 02-02-25 R. MONNIN B Five year review requirement. - ro 08-03-19 R. HEBER REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED

2、BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL FRYE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-12

3、-07 MICROCIRCUIT, LINEAR, DUAL, WIDEBAND, LOW NOISE, VOLTAGE FEEDBACK, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-94708 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E171-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without l

4、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q a

5、nd M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the follow

6、ing example: 5962 - 94708 01 M P A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-

7、38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s)

8、 identify the circuit function as follows: Device type Generic number Circuit function 01 CLC428 Dual, wideband, low noise, voltage feedback, operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device

9、 class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are

10、as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided b

11、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 7 V d

12、c Output current (IOUT) 96 mA Differential input voltage 10 V Common mode input voltage VSShort circuit current . 2/ Power dissipation (PD) 1.5 W Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +200C Storage temperature range . -65C to +150C Thermal resistance, junction-to

13、-case (JC) . MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 115C/W 1.4 Recommended operating conditions. Supply voltage (VS) . 5 V dc Gain range (AV) +1 V/V and up Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and

14、 handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circ

15、uits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780

16、- Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the eve

17、nt of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating m

18、ay cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Output is short circuit protected to ground, however maximum reliability is obtained if output current does not exceed 96 mA. Provided by IHSNot for ResaleNo reproduct

19、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes

20、Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shal

21、l be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38

22、535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unles

23、s otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups speci

24、fied in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limita

25、tions, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-3

26、8535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device cla

27、sses Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved sourc

28、e of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for devi

29、ce class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to

30、this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device c

31、lass M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device clas

32、s M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHI

33、O 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Static and dc tests. Input bias current IB1 01 -25 +25 A 2 -30 +30 3 -8

34、0 +80 Input offset current ISO3/ 1 01 -3 +3 A 2 -5 +5 3 -10 +10 Input offset voltage VIO1 01 -2 +2 mV 2,3 -5 +5 TC(IIN) TA= +125C, -55C 3/ 2 01 -400 +400 nA/C Average input bias current drift 3 -800 +800 Average input offset voltage drift TC(VIO) TA= +125C, -55C 3/ 2,3 01 -30 +30 V/C TC(IIO) TA= +12

35、5C, -55C 3/ 2 01 -50 +50 nA/C Average input offset current drift 3 -80 +80 Supply current ICCPer channel, RL= 1,2 01 12 mA 3 15 PSRR +VS= +4.0 V to +5.0 V, 1 01 60 dB Power supply rejection ratio -VS= -4.0 V to 5.0 V 2,3 55 CMRR VCM= 1 V 4 01 57 dB Common mode 3/ rejection ratio 5,6 52 See footnotes

36、 at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance

37、characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Frequency domain tests. Small signal bandwidth SSBW -3 dB bandwidth, 4,6 01 50 MHz VOUT 0.5 VPP5 35 Large signal bandwidth LSBW -3 dB bandwidth, 3/ 4,6 0

38、1 25 MHz VOUT 5.0 VPP5 15 Gain bandwidth product GBWP VOUT 0.5 VPP3/ 4,6 01 100 MHz 5 60 Gain flatness peaking GFP 0.1 MHz to 200 MHz, 4,5 01 0.6 dB VOUT 0.5 VPP6 1.0 Gain flatness rolloff GFR 0.1 MHz to 20 MHz, 4,6 01 0.5 dB VOUT 0.5 VPP5 1.0 Open loop gain AOL4 01 56 dB 5 48 6 53 Linear phase devi

39、ation LPD 0.1 MHz to 20 MHz, 3/ 4,6 01 1.0 Degrees VOUT 0.5 VPP5 1.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-39

40、90 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Distortion and noise tests. HD2 1 VPPat 10 MHz 4,6 01 50 dBc Second har

41、monic distortion 5 42 HD3 1 VPPat 10 MHz 4,6 01 60 dBc Third harmonic distortion 5 48 Crosstalk CT Input referred, 10 MHz 3/ 4,5,6 01 -58 dB Input noise voltage VN At 1 MHz to 100 MHz 3/ 4 01 2.5 nV / 5,6 3.0 Hz Input noise current ICN At 1 MHz to 100 MHz 3/ 4,5 01 3.0 pA / 6 5.2 Hz Timing tests. Ri

42、se and fall time tS1 V step 3/ 9,11 01 7.5 ns 10 12 Slew rate SR Measured 1 V with 3/ 2.5 V step, AV= +2 4,6 01 300 V/s 5 200 Settling time tS2 V step at 0.1 % of 3/ the final value 9,11 01 20 ns 10 30 Overshoot OS 1 V step 3/ 9 01 5 % 10,11 10 See footnotes at end of table. Provided by IHSNot for R

43、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Con

44、ditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Performance tests. RINC3/ 4,5 01 250 k Common mode input resistance 6 100 RIND3/ 4,5 01 50 k Differential mode input resistance 6 20 Common mode input capacitance CINC3/ 4,5,6 01 3.0 pFDifferenti

45、al mode input capacitance CIND3/ 4,5,6 01 3.0 pFOutput resistance ROUTClosed loop 3/ 4 01 0.1 5,6 0.3 Output voltage range VOUTRL= 3/ 1,2 01 -3.5 +3.5 V 3 -3.2 +3.2 VOUTLRL= 100 3/ 1,2 -3.2 +3.2 3 -1.2 +1.2 CMIR 3/ 1,2 01 -3.5 +3.5 V Common mode input voltage range 3 -3.2 +3.2 Output current IOUT3/

46、1,2 01 50 mA 3 18 1/ Unless otherwise specified, VS= 5 V dc, AV= +2, load resistance (RL) = 100 , and feedback resistance (RF) = 100 . 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be define

47、d as conventional current flow out of a device terminal. 3/ If not tested, shall be guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94708 DEFENSE SUPPLY C

48、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 Device type 01 Case outline P Terminal number Terminal symbol 1 OUTPUT 1 2 -INPUT 1 3 +INPUT 1 4 -VS5 +INPUT 2 6 -INPUT 2 7 OUTPUT 2 8 +VSFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D