DLA SMD-5962-92041 REV C-2012 MICROCIRCUIT LINEAR ANALOG SWITCH SPST 4-CHANNEL MONOLITHIC SILICON.pdf

《DLA SMD-5962-92041 REV C-2012 MICROCIRCUIT LINEAR ANALOG SWITCH SPST 4-CHANNEL MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-92041 REV C-2012 MICROCIRCUIT LINEAR ANALOG SWITCH SPST 4-CHANNEL MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R121-94. 94-02-17 M. A. Frye B Make change to paragraphs 4.2.1a.(1) and 4.4.3.1.a. - ro 01-07-06 R. Monnin C Redrawn. Update drawing to current requirements. - drw 12-06-18 Charles F. Saffle REV SHEET REV SH

2、EET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Dan Wonnell DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIE

3、S OF THE DEPARTMENT OF DEFENSE CHECKED BY Sandra Rooney APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, ANALOG SWITCH, SPST, 4-CHANNEL, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-03-04 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-92041 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E391-12 Pro

4、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assuran

5、ce class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels i

6、s reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92041 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA des

7、ignator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-)

8、indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 DG441A Quad, SPST analog switch 02 DG442A Quad, SPST analog switch 1.2.3 Device class designator. The device class designator is a single letter i

9、dentifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-

10、PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-

11、PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHE

12、ET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ +V to V 44 V dc GND to -V . 25 V dc Digital inputs to -V . (GND - 0.3 V dc) to 44 V dc 2/ VS, VDto -V (-V) -2 V dc to (+V) +2 V dc or 30 mA, 2/ whichever occurs first Current (any terminal), continuous 30 mA Current, S or D, pulsed, 1 ms, 1

13、0 percent duty cycle 40 mA Power dissipation (PD): Case outline E at +75C 900 mW 3/ Case outline 2 at +75C . 750 mW 3/ Junction temperature (TJ) . +175C Lead temperature (soldering, 10 seconds maximum) . +300C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) . See

14、MIL-STD-1835 1.4 Recommended operating conditions. +V . +15 V dc -V -15 V dc GND 0 V dc Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this d

15、rawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD

16、-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at ht

17、tps:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes preced

18、ence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect rel

19、iability. 2/ Signals on SX, DX, or INXexceeding +V or -V will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 3/ For case outline E, derate above +75C linearly at 12 mW/C. For case outline 2, derate above +75C linearly at 10 mW/C. Provided by IHSNot for ResaleN

20、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classe

21、s Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall

22、 be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-385

23、35, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Block dia

24、gram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply o

25、ver the full ambient case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 here

26、in. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be

27、marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PR

28、F-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawin

29、g (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved so

30、urce of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as

31、 required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change

32、of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review

33、 the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 82 (see

34、 MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc

35、e characteristics. Test Symbol Conditions -55C TA +125C +V = +15 V, -V = -15 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Drain-source “ON” resistance rDS(ON) VIN= 0.8 V, IS= -10 mA, VD= 8.5 V, 1, 3 01 85 +V = +13.5 V, -V = -13.5 V 2 100 VIN= 2.4 V, IS= -10 mA, VD=

36、8.5 V, 1, 3 02 85 +V = +13.5 V, -V = -13.5 V 2 100 VIN= 0.8 V, IS= -10 mA, VD= 3.0 V, 1, 3 01 160 +V = +10.8 V, -V = 0 V 2 200 VIN= 0.8 V, IS= -10 mA, VD= 8.0 V, 1, 3 160 +V = +10.8 V, -V = 0 V 2 200 VIN= 2.4 V, IS= -10 mA, VD= 3.0 V, 1, 3 02 160 +V = +10.8 V, -V = 0 V 2 200 VIN= 2.4 V, IS= -10 mA,

37、VD= 8.0 V, 1, 3 160 +V = +10.8 V, -V = 0 V 2 200 Source “OFF” leakage current IS(OFF) VIN= 2.4 V, VD= 15.5 V, VS= 15.5 V, 1 01 -0.5 +0.5 nA +V = +16.5 V, -V = -16.5 V 2, 3 -20 +20 VIN= 0.8 V, VD= 15.5 V, VS= 15.5 V, 1 02 -0.5 +0.5 +V = +16.5 V, -V = -16.5 V 2, 3 -20 +20 Drain “OFF” leakage current I

38、D(OFF) VIN= 2.4 V, VD= 15.5 V, VS= 15.5 V, 1 01 -0.5 +0.5 nA +V = +16.5 V, -V = -16.5 V 2, 3 -20 +20 VIN= 0.8 V, VD= 15.5 V, VS= 15.5 V, 1 02 -0.5 +0.5 +V = +16.5 V, -V = -16.5 V 2, 3 -20 +20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M

39、ICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics continued. Test Symbol Conditions -55C TA +125C +V = +15 V, -V = -15 V Group A subgroups Device type Limits Unit unless

40、 otherwise specified Min Max Channel “ON” leakage current ID(ON) + VIN= 0.8 V, VS= VD= 15.5 V, 1 01 -0.5 +0.5 nA IS(ON) +V = +16.5 V, -V = -16.5 V 2, 3 -40 +40 VIN= 2.4 V, VS= VD= 15.5 V, 1 02 -0.5 +0.5 +V = +16.5 V, -V = -16.5 V 2, 3 -40 +40 Input current with VINlow IILVINunder test = 0.8 V, all o

41、ther = 2.4 V 1, 2, 3 All -0.5 +0.5 A Input current with VINhigh IIHVINunder test = 2.4 V, all other = 0.8 V 1, 2, 3 All -0.5 +0.5 A Positive supply current +I +V = +16.5 V, -V = -16.5 V, VIN= 0 V 1, 2, 3 All 0.1 mA +V = +16.5 V, -V = -16.5 V, VIN= 5 V 0.1 +V = +13.2 V, -V = 0 V, VIN= 0 V 0.1 +V = +1

42、3.2 V, -V = 0 V, VIN= 5 V 0.1 Negative supply current -I +V = +16.5 V, -V = -16.5 V, VIN= 0 V 1, 3 All -1.0 A 2 -100 +V = +16.5 V, -V = -16.5 V, VIN= 5 V 1, 3 -1.0 2 -100 +V = +13.2 V, -V = 0 V, VIN= 0 V 1, 3 -1.0 2 -100 +V = +13.2 V, -V = 0 V, VIN= 5 V 1, 3 -1.0 2 -100 Provided by IHSNot for Resale

43、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics continued. Test Symbol Conditions -55C T

44、A +125C +V = +15 V, -V = -15 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Ground current IGND+V = +16.5 V, -V = -16.5 V, VIN= 0 V 1, 2, 3 All -100 A +V = +16.5 V, -V = -16.5 V, VIN= 5 V -100 +V = +13.2 V, -V = 0 V, VIN= 0 V -100 +V = +13.2 V, -V = 0 V, VIN= 5 V -100

45、 Turn-on time tONVS= 10 V, RL= 1 k, CL= 35 pF, see figure 4 9 01 250 ns 02 315 10, 11 01 300 02 400 Turn-on time tONVS= 8.0 V, RL= 1 k, +V = +12 V, -V = 0 V, 9 01 400 ns CL= 35 pF, see figure 4 02 450 10, 11 01 600 02 675 Turn-off time tOFFVS= 10 V, RL= 1 k, CL= 35 pF, see figure 4 9 01 120 ns 02 21

46、0 10, 11 01 150 02 250 VS= 8.0 V, RL= 1 k, +V = +12 V, -V = 0 V, CL= 35 pF, see figure 4 9, 10, 11 All 200 Functional test FT See 4.4.1c 7, 8 All Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND

47、 AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outlines E 2 Terminal number Terminal symbol 1 IN1NC 2 D1IN13 S1D14 -V S15 GND -V 6 S4NC 7 D4GND 8 IN4S49 IN3D410 D3IN411 S3NC 12 NC IN313 +V D314 S2S315 D2NC 16 IN2NC 17 - +V 18 - S219

48、 - D220 - IN2NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92041 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device types Logic Switch 01 0 ON 1 OFF 02 0 OFF 1 ON FIGURE 2. Truth table