DLA SMD-5962-91748 REV B-2010 MICROCIRCUIT LINEAR HIGH SPEED VIDEO 8-BIT DIGITAL-TO-ANALOG CONVERTER MONOLITHIC SILICON.pdf

《DLA SMD-5962-91748 REV B-2010 MICROCIRCUIT LINEAR HIGH SPEED VIDEO 8-BIT DIGITAL-TO-ANALOG CONVERTER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-91748 REV B-2010 MICROCIRCUIT LINEAR HIGH SPEED VIDEO 8-BIT DIGITAL-TO-ANALOG CONVERTER MONOLITHIC SILICON.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change generic number for device types 01 and 02. Changes to table I. Editorial changes throughout. 95-11-01 M. A. Frye B Redraw. Update drawing to current requirements. drw 10-01-08 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS

2、BEEN REPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Dan Wonnell DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS

3、 AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Sandra Rooney APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, HIGH SPEED, VIDEO, 8-BIT, DIGITAL-TO-ANALOG CONVERTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-10-19 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-91748 SHEET 1 OF 10 DSC

4、C FORM 2233 APR 97 5962-E134-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope

5、. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of

6、 Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91748 01 M J A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) /

7、(see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with t

8、he appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 1018A Digital-to-Analog converter, 275 MWPS, 8-bit, video 02 1018B Digital-to-Analog converter, 165 MWPS

9、, 8-bit, video 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircui

10、ts in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline. The case outline is as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style J GDIP1-T24 or CDIP2-T24 24 Dual-in-line 1.2.5 L

11、ead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91748 DEFENSE SUPPLY CE

12、NTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ VEED(measured to VCCD) -7.0 V dc to +0.5 V dc VEEA(measured to VCCA) -7.0 V dc to +0.5 V dc VCCA(measured to VCCD) -0.5 V dc to +0.5 V dc CONV, Data, and controls (measured to VCCD

13、) VEEDto + 0.5 V dc REF+ (measured to VCCA) VEEAto + 0.5 V dc REF- (measured to VCCA) . VEEAto + 0.5 V dc Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +175C Storage temperature -60C to +150C Power dissipation (PD) . 1.2 W Thermal resistance, junction-to-ambient (JA) 7

14、5.2C/W Thermal resistance, junction-to-case (JC) . 25C/W 1.4 Recommended operating conditions. Negative supply (VEE) . -5.5 V dc to -4.9 V dc Ambient operating temperature range (TA) -55C to +125C Reference current (ISET) . 1.105 mA Input capacitance, REF+ and REF- (CIN) . 5 pF (typical) Input capac

15、itance, data and controls (CINDC) 3 pF (typical) Output capacitance (COUT) . 12 pF (typical) Current settling time, clocked mode, (tS): 2/ To 0.2% 7 ns (typical) To 0.8% 5.5 ns (typical) To 0.2%, RL= 25 . 4.5 ns (typical) Rise time, RL= 25 . 1 ns (typical) Gain error tempco (AET) . 150 ppm/C Glitch

16、energy, area = 1/2 VT (GE) 2/ 4 pV-s (typical) Reference bandwidth, -3 dB (BW) 2/ 1 MHz (typical) 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless o

17、therwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-

18、STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from t

19、he Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwis

20、e specified, RL= 37.5 and CL= 5 pF. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of p

21、recedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item req

22、uirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described h

23、erein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MI

24、L-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performa

25、nce characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements

26、. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking o

27、f the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. M

28、arking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-3

29、8535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required

30、 from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q

31、and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A

32、 shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawin

33、g. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.1

34、0 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 56 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

35、SIZE A 5962-91748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C VEEA= VEED= -5.2 V 0.3 V, VCCA= 0 V, VCCD= 0 V, ISET= 1.105 mA Group A subgroups Device type

36、Limits 1/ Unit unless otherwise specified Min Max Integral linearity error IL1.0 mA ISET 1.3 mA 1, 2, 3 All -0.95 +0.95 LSB Differential linearity error DL1.0 mA ISET 1.3 mA 1, 2, 3 All -0.50 +0.50 LSB Gain error AE1, 2, 3 All -6.5 +6.5 % FSR Compliance voltage, + output +VOC1, 2, 3 All -1.2 +1.5 V

37、Compliance voltage, - output -VOC1, 2, 3 All -1.2 +1.5 V Equivalent output resistance RO1, 2, 3 All 20 k Output offset current IOSESYNC = Blank = 0, FH = BRT = 1 1, 2, 3 All 0.5 LSB Input voltage, logic high VIH1, 2, 3 All -1.0 V Input voltage, logic low VIL1, 2, 3 All -1.5 V Convert voltage, common

38、 mode range 2/ VCMR1, 2, 3 All -0.5 -2.5 V Convert voltage, differential 2/ VDIFF1, 2, 3 All 0.4 1.2 V Input I, logic LOW, data and controls IILVIL= -1.5 V max 1, 2, 3 All 120 A Input I, logic HIGH, data and controls IIHVIH= 1.0 V min 1, 2, 3 All 120 A Input I, convert IICVIL= -1.5 V max 1, 2, 3 All

39、 60 A Power supply sensitivity PSS -5.5 V to -4.9 V 1, 2, 3 All -120 +120 A/V Supply current IEEA+IEEDVEEA= VEED= 5.5 V 1, 2, 3 All 220 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SI

40、ZE A 5962-91748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions -55C TA+125C VEEA= VEED= -5.2 V 0.3 V, VCCA= 0 V, VCCD= 0 V, ISET= 1.105 mA Group A subgroups De

41、vice type Limits 1/ Unit unless otherwise specified Min Max Maximum conversion rate FSTA= 25C 3/ 9 01 275 MWPS 02 165 Rise time 4/ tR10% to 90% of gray scale 3/ 9, 10, 11 All 2.0 ns Clock to output delay clocked mode 4/ tCODFT = 0 3/ 9, 10, 11 All 4.5 ns Clock to output delay transparent mode 4/ tDO

42、DFT = 1 3/ 9, 10, 11 All 6.0 ns Convert pulse width, low or high tCPTA= 25C 9 01 1.8 ns 02 3.0 Set-up time, data and controls 4/ tSU3/ 9, 10, 11 All 1.0 ns Hold time, data and controls 4/ tH3/ 9, 10, 11 All 0.5 ns Slew rate 4/ SR 20% to 80% of gray scale 3/ 9, 10, 11 All 325 V/s Clock feedthrough 4/

43、 FTC3/ 9, 10, 11 All -48 dB 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 2/ Parameter guaranteed by design and characterizatio

44、n data, but not tested. 3/ RL= 37.5 and CL= 5 pF. 4/ For subgroups 10 and 11, the parameter is guaranteed by design and characterization data, but not tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9

45、1748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 and 02 Case outline J Terminal number Terminal symbol and function 1 D3 Data bit 3 2 D2 Data bit 2 3 D1 Data bit 1 4 D0 Data bit 0 (LSB) 5 VEEDDigital negative supply 6 CONV Co

46、nvert clock input 7 CONV Convert clock input complement 8 FT Register feedthrough control 9 VCCDDigital positive supply 10 FH Data force high control 11 BLANK Video blank input 12 BRT Video bright input 13 SYNC Video SYNC input 14 REF- Reference current - input 15 REF+ Reference current + input 16 C

47、OMP Compensation input 17 VCCAAnalog positive supply 18 OUT- Output current negative 19 OUT+ Output current positive 20 VEEAAnalog negative supply 21 D7 Data bit 7 (MSB) 22 D6 Data bit 6 23 D5 Data bit 5 24 D4 Data bit 4 FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or

48、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91748 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit,