DLA SMD-5962-91523 REV C-2013 MICROCIRCUIT LINEAR VOLTAGE REGULATOR POSITIVE 20 V FIXED MONOLITHIC SILICON.pdf

《DLA SMD-5962-91523 REV C-2013 MICROCIRCUIT LINEAR VOLTAGE REGULATOR POSITIVE 20 V FIXED MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-91523 REV C-2013 MICROCIRCUIT LINEAR VOLTAGE REGULATOR POSITIVE 20 V FIXED MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 00-09-08 R. MONNIN B Add a footnote to the case outline U, TO-257 package as specified under 1.2.3 and figure 1. - ro 04-05-03 R. MONNIN C Update drawing to current MIL-PRF-38535 requirements.

2、 -rrp 13-05-13 C. SAFFLE REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY MARCIA B. KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS

3、AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY SANDRA B. ROONEY APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, POSITIVE, 20 V FIXED, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-03-16 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 596

4、2-91523 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E380-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1.

5、 SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When availabl

6、e, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91523 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finis

7、h (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and a

8、re marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 SG7820A Voltage regulator, fixed 20 V 1.2.3 Device class designator. The device clas

9、s designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certif

10、ication and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U 1/ See figure 1 3 TO-257 single row flange mounted with isolated tab and glass sealed X See figure 1

11、 3 TO-39 can Y See figure 1 2 TO-3 flange mount Z MBFM4-P2 2 TO-66 flange mount 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. _ 1/ For outline letter U, CAGE 34333 manufacturers the TO-257 package with

12、ceramic seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 2/ Input voltag

13、e: Operating or output shorted to ground 35 V dc Transient . 50 V dc 3/ Output current (IO): Case X 0.5 A Cases U, Y, and Z . 1.5 A Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Power dissipation (PD): TC= +25C: Case X .

14、2 W Case Y . 20 W Cases U and Z . 15 W TA= +25C: Case X . 1.0 W Case Y . 4.3 W Cases U and Z . 3.0 W Thermal resistance, junction-to-case (JC): Case U 4.2C/W Case X 15C/W Case Y 3C/W Case Z 6C/W Thermal resistance, junction-to-ambient (JA): Case X 120C/W Case Y 35C/W Cases U and Z 42C/W 1.4 Recommen

15、ded operating conditions. Input voltage range (VIN) +16.5 V dc to +50 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the e

16、xtent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. _ 2/ Stresses above the absolute maximum rating may ca

17、use permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 3/ The 50-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage. Since the regulators maximum current capabili

18、ty is reduced, the output may fall out of regulation at high voltages under nominal loading. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVE

19、L C SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Mic

20、rocircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and th

21、e references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall

22、be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordanc

23、e with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A a

24、nd herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless

25、otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specifi

26、ed in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitati

27、ons, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-385

28、35, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device class

29、es Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source

30、of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and her

31、ein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuit

32、s delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc

33、e characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTTA= +25C 1 01 19.7 20.3 V Ripple rejection 2/ VIN/ VOUTf = 120 Hz, VIN= 10 V, TA= +25C 4 01 58 dB Line regulation 2/ VRLINEVIN= 27 V to 35 V, TA=

34、 +25C 1 01 100 mV VIN= 26 V to 32 V, TA= +25C 50 Load regulation 2/ VRLOADIO= 5.0 mA to 1.5 A, 3/ TA= +25C 1 01 140 mV IO= 250 mA to 750 mA, 3/ TA= +25C 70 IO= 5 mA to 500 mA, 4/ TA= +25C 70 Dropout voltage VDOVOUT= 100 mV, 3/ IO= 1.0 A, TA= +25C 1 01 2.5 V VOUT= 100 mV, 4/ IO= 500 mA, TA= +25C 2.5

35、Peak output current IO(PK) TA= +25C 3/ 1 01 1.5 3.3 A TA= +25C 4/ 0.5 1.7 Short circuit current 5/ IOSVIN= 35 V, TA= +25C 3/ 1 01 1.2 A VIN= 35 V, TA= +25C 4/ 0.7 Output noise voltage NOf = 10 Hz to 100 kHz 6/ TA= +25C 7 01 40 V/V Long term stability VOUT/ t t = 1,000 hours 6/ TA= +125C 8A 01 96 mV

36、Thermal shutdown T / t IO= 5.0 mA 1,2,3 01 175 C See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 D

37、SCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Total output voltage tolerance VOTIO= 5.0 mA to 1 A, 3/ VIN= 24 V to 35 V, P 20 W 1,2,3 01 19.4 20.6 V

38、IO= 5.0 mA to 500 mA, 4/ VIN= 24 V to 35 V, P 2 W 19.4 20.6 Quiescent current change with line ISCD(line) VIN= 24 V to 35 V 1,2,3 01 0.8 mA Quiescent current change with load ISCDIO= 5.0 mA to1 A 3/ 1,2,3 01 0.5 mA (load) IO= 5.0 mA to 500 mA 4/ 0.5 Quiescent current ISCD1 01 6.0 mA 2,3 7.0 1/ Unles

39、s otherwise specified, for device type 01, VIN= 29 V, and IO= 500 mA for cases Y and Z, VIN= 29 V and IO= 100 mA for case X. CIN= 0.33 F and COUT= 0.1 F. 2/ All measurements except output noise voltage and ripple rejection are made at constant junction temperature and with low duty cycle. 3/ For cas

40、es Y and Z only. 4/ For case X only. 5/ Short circuit protection is only assured up to VIN= 35 V. 6/ Guaranteed, if not tested, to the limits specified in table I herein. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product

41、(see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufa

42、cturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 76 (see MIL-PRF-38

43、535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline U Inches Millimeters .005 0.

44、13 .010 0.25 .020 0.51 Symbol Inches Millimeter Min Max Min Max A .190 .200 4.83 5.08 A1.035 .045 0.89 1.14 A2.120 BSC 3.05 BSC b .025 .035 0.64 0.89 D .645 .665 16.38 16.89 D1.410 .430 10.41 10.92 D3.000 .065 0.00 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.71 L .500 .750 12.70 19.05 O .527 .537

45、13.39 16.64 P .140 .150 3.56 3.81 NOTE: 1. The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall

46、 take precedence. 2. For case outline U only, CAGE code 34333, the ceramic seal that protrudes from the seating plane is not to be considered in overall package dimensions. The ceramic seal protrusion is considered uncontrolled within an area 30 mils from the seating plane. FIGURE 1. Case outline. P

47、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91523 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline X Symbol Inches Millimeter Notes Min Max Min Ma

48、x A .165 .185 4.19 4.70 b .016 .019 0.41 0.48 2 b1.016 .021 0.41 0.53 2 D .335 .370 8.51 9.40 D1.305 .335 7.75 8.51 e .200 T.P. 5.08 T.P. 4 e1.100 T.P. 2.54 T.P. 4 F - .050 - 1.27 k .028 .034 0.71 0.86 k1.029 .045 0.74 1.14 3 k2.009 .041 0.23 1.04 L .500 - 12.70 - L1- .050 - 1.27 L2.250 6.35 - 45 T.P. 45 T.P. 4 NOTES: 1. The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement,