DLA SMD-5962-91508 REV D-2013 MICROCIRCUIT MEMORY DIGITAL CMOS 16K X 8 DUAL PORT STATIC RANDOM ACCESS MEMORY (SRAM) MONOLITHIC SILICON.pdf

《DLA SMD-5962-91508 REV D-2013 MICROCIRCUIT MEMORY DIGITAL CMOS 16K X 8 DUAL PORT STATIC RANDOM ACCESS MEMORY (SRAM) MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-91508 REV D-2013 MICROCIRCUIT MEMORY DIGITAL CMOS 16K X 8 DUAL PORT STATIC RANDOM ACCESS MEMORY (SRAM) MONOLITHIC SILICON.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 07 and 08. Add SEM condition to VDRand ICC6in table I. Add footnote 2/ to semaphore truth table on sheet 15. Add footnote 2/ to interrupt flag truth table on sheet 16. Add note 2/ to sheet 17. Add SEM and note 9 on sheet 20. Upda

2、te boilerplate. Editorial changes throughout. 96-10-10 Ray Monnin B Add device types 09-12 and added CAGE 61772 as a source for those devices. 97-01-17 Ray Monnin C Boilerplate update and part of five year review. tcr 07-01-31 Joseph Rodenbeck D Updated drawing to meet current MIL-PRF-38535 requirem

3、ents. glg 13-07-25 Charles Saffle REV SHEET REV D D D D D D D D D D D D D D D D D SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Jeff Bowling DLA LAND AND MARITIME STANDARD MICR

4、OCIRCUIT DRAWING CHECKED BY Jeff Bowling COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, MEMORY, DIGITAL, CMOS, 16K X 8 DUAL PORT STATIC RANDOM ACCESS MEMORY (SRAM), MONOLITHIC SILICON AND AGEN

5、CIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-04-15 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-91508 SHEET 1 OF 31 DSCC FORM 2233 APR 97 5962-E509-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN

6、G SIZE A 5962-91508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of

7、 case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91508 01 M X A Federal stock class d

8、esignator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the app

9、ropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type

10、 Generic number Circuit function Data retention Access time 01 7006 16k X 8 Dual Port Static RAM No 70ns 02 7006 16k X 8 Dual Port Static RAM Yes 70ns 03 7006 16k X 8 Dual Port Static RAM No 55ns 04 7006 16k X 8 Dual Port Static RAM Yes 55ns 05 7006 16k X 8 Dual Port Static RAM No 45ns 06 7006 16k X

11、 8 Dual Port Static RAM Yes 45ns 07 7006 16k X 8 Dual Port Static RAM No 35ns 08 7006 16k X 8 Dual Port Static RAM Yes 35ns 09 7006 16k X 8 Dual Port Static RAM No 25ns 10 7006 16k X 8 Dual Port Static RAM Yes 25ns 11 7006 16k X 8 Dual Port Static RAM No 20ns 12 7006 16k X 8 Dual Port Static RAM Yes

12、 20ns 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in acc

13、ordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CMGA3-PN 68 pin grid array Y See figure 1 68 fla

14、t pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91508 DLA

15、 LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc Storage temperature range . -65C to +150C DC output current 50 mA Maximum power dissipation (PD) 2.2 W Lead temperature

16、(soldering, 10 seconds) 260C Thermal resistance, junction-to-case (JC): Case X See MIL-STD-1835 Case Y . 20C/W Maximum junction temperature (TJ) +150C 3/ DC input voltage range . -0.5 V dc to VCC+ 0.5 V dc 4/ DC output voltage range . -0.5 V dc to VCC+ 0.5 V dc 4/ Output voltage applied in high Z st

17、ate . -0.5 V dc to VCC+ 0.5 V dc 1.4 Recommended operating conditions. Supply voltage (VCC) +4.5 V dc to +5.5 V dc High level input voltage (VIH) +2.2 V dc to +6.0 V dc Low level input voltage (VIL) 2/ -0.5 V dc to +0.8 V dc Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMEN

18、TS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENS

19、E SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List o

20、f Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolu

21、te maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltages referenced to GND unless otherwise specified. 3/ Maximum junction temperature shall not be exceeded except for allowable short duration

22、 burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 4/ Negative undershoots to a minimum of -3.0 V are allowed with a maximum of 20 ns pulse width. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING

23、 SIZE A 5962-91508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are the issu

24、es of the documents cited in the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM Standard F1192-00 - Standard Guide for the Measurement of Single Event Phenomena (SEP) induced by Heavy Ion Irradiation of Semiconductor Devices. (Applications for copies of ASTM publications should

25、 be addressed to: ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; http:/www.astm.org.) ELECTRONICS INDUSTRIES ASSOCIATION (EIA) JEDEC INTERNATIONAL (JEDEC) JESD 78 - IC Latch-Up Test. (Applications for copies should be addressed to JEDEC Solid State Technolo

26、gy Association, 3103 North 10thStreet, Suite 240-S, Arlington, VA 22201-2107; http:/www.jedec.org.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries o

27、r other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption

28、has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not a

29、ffect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and

30、physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connec

31、tions shall be as specified on figure 2. 3.2.3 Truth table. The truth table shall be as specified on figure 3. 3.2.4 Functional tests. Various functional tests used to test this device are contained in the appendix. If the test patterns cannot be implemented due to test equipment limitations, altern

32、ate test patterns to accomplish the same results shall be allowed. For device class M, alternate test patterns shall be maintained under document revision level control by the manufacturer and shall be made available to the preparing or acquiring activity upon request. For device classes Q and V alt

33、ernate test patterns shall be under the control of the device manufacturers Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the preparing or acquiring activity upon request. 3.2.5 Die overcoat. Polyimide and silicone coatings are allowable as an overcoat

34、 on the die for alpha particle protection only. Each coated microcircuit inspection lot (see inspection lot as defined in MIL-PRF-38535) shall be subjected to and pass the internal moisture content test at 5000 ppm (see method 1018 of MIL-STD-883). The frequency of the internal water vapor testing s

35、hall not be decreased unless approved by the preparing activity for class M. The TRB will ascertain the requirements as provided by MIL-PRF-38535 for classes Q and V. Samples may be pulled any time after seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

36、IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91508 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance charac

37、teristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defi

38、ned in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“

39、 on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certif

40、ication mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from

41、a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate o

42、f compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, a

43、ppendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for dev

44、ice class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime,

45、DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device c

46、lass M devices covered by this drawing shall be in microcircuit group number 41 (see MIL-PRF-38535, appendix A). 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufact

47、urers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices p