DLA SMD-5962-90962 REV C-2013 MICROCIRCUIT LINEAR RESOLVER-TODIGITAL CONVERTER MONOLITHIC SILICON.pdf

《DLA SMD-5962-90962 REV C-2013 MICROCIRCUIT LINEAR RESOLVER-TODIGITAL CONVERTER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90962 REV C-2013 MICROCIRCUIT LINEAR RESOLVER-TODIGITAL CONVERTER MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 01-11-15 R. MONNIN B Drawing updated as part of 5 year review. -rrp 07-02-05 J. RODENBECK C Update drawing to current MIL-PRF-38535 requirements. -rrp 13-09-23 C. SAFFLE THE ORIGINAL FIRST SHE

2、ET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS D

3、RAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RESOLVER-TO-DIGITAL CONVERTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-12-02 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 59

4、62-90962 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E564-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1

5、. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When availab

6、le, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90962 01 M Q A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead fini

7、sh (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and

8、are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AD2S80A Resolver-to-digital converter, 4 arc minute accuracy and 10 to 16 bits reso

9、lution 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in ac

10、cordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Q GDIP1-T40 or CDIP2-T40 40 Dual-in-line X CQCC1-

11、N44 44 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

12、DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Positive power supply (+VS) to GND . +14.0 V dc 2/ 3/ Negative power supply (-VS) to GND -14.0 V dc 2/ 3/ Logic power supply (VL) +VS2/ Digital in

13、put voltage to GND -0.4 V to VLVoltage controlled oscillator (VCO) input . +14.0 V to -VS2/ 3/ Demodulator (DEMOD) INPUT +14.0 V to -VSINTEGRATOR INPUT . +14.0 V to -VSVREFto GND . +14.0 V to -VS4/ Analog input voltage (SIN, COS) to GND +14.0 V to -VS4/ Power dissipation (PD) 860 mW Storage temperat

14、ure range -65C to +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-case (JA) : Case Q . 11C/W Case X . 10C/W 1.4 Recommended operating conditions. Power supply voltage (+VSto -VS) 12 V dc 10 % Power supply voltage (VL) . +5 V 10 % ANALOG GND = DIGITA

15、L GND 0 V 5/ Analog input voltage (SIN, COS) . 2 VRMS10 % Analog input voltage (REF) 1 V to 8 V peak Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a p

16、art of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STAN

17、DARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available

18、 online at http:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade perform

19、ance and affect reliability. 2/ GND refers to ANALOG GND. 3/ SIGNAL GND is internally connected to ANALOG GND. 4/ SIN, COS, REF input voltage may be present without +VS, -VS, VL. 5/ ANALOG GND must be externally connected to DIGITAL GND. Provided by IHSNot for ResaleNo reproduction or networking per

20、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the

21、 text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-

22、38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix

23、 A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.

24、3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The block diagram shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradi

25、ation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements

26、 shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not

27、 feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be

28、 in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate

29、of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to b

30、e listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requir

31、ements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provide

32、d with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawin

33、g. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore

34、at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 81 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

35、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits

36、 2/ Unit Min Max Angular accuracy 3/ +VS= +10.8 V dc, -VS= -10.8 V dc, VL= 5.0 V dc, SC1 = SC2 = high, 16 bit resolution 1,2,3 01 4 arc mins +VS= +13.2 V dc, -VS= -13.2 V dc, VL= 5.0 V dc, SC1 = SC2 = high, 16 bit resolution 4 Missing codes 3/ +VS= +10.8 V dc, -VS= -10.8 V dc, VL= 5.0 V dc, SC1 = SC

37、2 = high, 16 bit resolution 1,2,3 01 4 codes +VS= +13.2 V dc, -VS= -13.2 V dc, VL= 5.0 V dc, SC1 = SC2 = high, 16 bit resolution 4 Total effective angular offset Output data nulled by application of offset current to integrator input 1,2,3 01 800 nA DEMOD OUTPUT 3/ scaling 1,2,3 01 90 110 nA/bit VCO

38、 total effective offset Measured with 68 k input resistance 1,2 01 380 nA 3 400 INTEGRATOR OUTPUT range VS= 12 V dc, VL= 5.0 V dc, 1 mA load 1,2,3 01 8 V VS= 10.8 V dc, VL= 5.0 V dc, 1 mA load 7 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

39、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A

40、 subgroups Device type Limits 2/ Unit Min Max Digital inputs high voltage VIHDB1 DB16, INHIBIT , ENABLE , BYTE SELECT, VS= 10.8 V dc, VL= 5.0 V dc 1,2,3 01 2.0 V Digital inputs low voltage VILDB1 DB16, INHIBIT , ENABLE , BYTE SELECT, VS= 13.2 V dc, VL= 5.0 V dc 1,2,3 01 0.8 V Digital inputs high cur

41、rent IIHDB1 DB16, INHIBIT , ENABLE , BYTE SELECT, VS= 13.2 V dc, VL= 5.5 V dc, VIH= 5.5 V dc 1,2,3 01 100 A Digital inputs low current IILDB1 DB16, INHIBIT , ENABLE , BYTE SELECT, VS= 13.2 V dc, VL= 5.5 V dc, VIL= 0.0 V dc 1,2,3 01 100 A Digital inputs low 4/ voltage VILSC1, SC2, DATA LOAD, VS= 12.0

42、 V dc, VL= 5.0 V dc, ENABLE = high 1,2,3 01 1.0 V Digital inputs low 4/ current IILSC1, SC2, DATA LOAD, VS= 12.0 V dc, VL= 5.0 V dc, ENABLE = high 1,2,3 01 -400 A Digital outputs high voltage VOHDB1 DB16, RIPPLE CLOCK, DIRECTION, VS= 12.0 V dc, VL= 4.5 V dc, IOH= 100 A 1,2,3 01 2.4 V See footnotes a

43、t end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteris

44、tics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Digital outputs low voltage VOLDB1 DB16, RIPPLE CLOCK, DIRECTION, VS= 12.0 V dc, VL= 5.5 V dc, IOL= 1.2 mA 1,2,3 01 0.4 V Floating state leakage current ILKGDB1 DB1

45、6 only, VS= 12.0 V dc, VL= 5.5 V dc, VOL= 0.0 V 1,2,3 01 100 A DB1 DB16 only, VS= 12.0 V dc, VL= 5.5 V dc, VOH= 5.0 V 100 Power supply current from +VS+IS+VS= +13.2 V dc 1,2,3 01 30 mA Power supply current from -VS-IS-VS= -13.2 V dc 1,2,3 01 -30 mA Power supply current from +VL+ILVL= 5.5 V dc 1,2,3

46、01 1.5 mA VCO maximum rate 4,5,6 01 1.1 MHz VCO gain scaling Measured with VCO input current of 10 A 4,5,6 01 7110 8690 Hz/A VCO linearity 5/ VCO measured at 10 points over the frequency range 0.0 MHz to 1.0 MHz 4,5,6 01 3 percent Busy pulse width 3/ tBUSY9,10,11 01 200 600 ns 1/ +VS= +12.0 V dc, -V

47、S= -12.0 V dc, VL= +5.0 V dc. 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ VSIN, VCOS= 2 VRMSmaximum at 5 kHz. VREF= 2 V

48、RMSat 5 kHz. 4/ Digital inputs SC1, SC2, DATA LOAD are internally pulled up to +VS. 5/ VCO linearity is expressed as percentage of reading. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90962 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines Q X Terminal number Terminal symbol 1