DLA SMD-5962-90707 REV G-2006 MICROCIRCUIT HYBRID LINEAR SYNCHRO-TO-DIGITAL CONVERTER《同步到数字转换器 直线式混合微型电路》.pdf

《DLA SMD-5962-90707 REV G-2006 MICROCIRCUIT HYBRID LINEAR SYNCHRO-TO-DIGITAL CONVERTER《同步到数字转换器 直线式混合微型电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90707 REV G-2006 MICROCIRCUIT HYBRID LINEAR SYNCHRO-TO-DIGITAL CONVERTER《同步到数字转换器 直线式混合微型电路》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 05 through 08. Add vendor CAGE 09059. Editorial changes throughout. 91-11-12 Gregory Lude B Add case outline Y. Rewrite entire document. 93-06-11 K. A. Cottongim C Made changes to table I for tests Drive capability (IX), AC error

2、, DC velocity voltage, and Filtered dc error. Changed terminal symbol for terminal number 23 in figure 2. 93-11-09 K. A. Cottongim D Changes in accordance with NOR 5962-R162-95. 95-06-16 K. A. Cottongim E Changes in accordance with NOR 5962-R316-96. 96-02-13 K. A. Cottongim F Changes in accordance w

3、ith NOR 5962-R158-97. 96-12-20 K. A. Cottongim G Update drawing to current requirements of MIL-PRF-38534. 06-02-14 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV G SHEET 15 REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12

4、13 14 PMIC N/A PREPARED BY Steve L. Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber POST OFFICE BOX 3990 COLUMBUS, OHIO 43218-3390 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, H

5、YBRID, LINEAR, SYNCHRO-TO-DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-10-19 AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 67268 5962-90707 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E268-06Provided by IHSNot for ResaleNo reproduction or networking permitted withou

6、t license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90707 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A

7、choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90707 01 H X X Federa

8、l RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA level

9、s and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic number Circuit function Accuracy (1.0 LSB) 01 SDC14500-635 400 Hz, 11.8 V, Synchro-to-digital

10、 converter 2.6 arc minutes 01 HSDC-8917II-1-A 400 Hz, 11.8 V, Synchro-to-digital converter 2.6 arc minutes 02 SDC14500-636 400 Hz, 11.8 V, Synchro-to-digital converter 4.0 arc minutes 02 HSDC-8917II-1 400 Hz, 11.8 V, Synchro-to-digital converter 4.0 arc minutes 03 SDC14502-605 60 Hz, 90 V, Synchro-t

11、o-digital converter 2.6 arc minutes 03 HSDC-8919II-1-A 60 Hz, 90 V, Synchro-to-digital converter 2.6 arc minutes 04 SDC14502-606 60 Hz, 90 V, Synchro-to-digital converter 4.0 arc minutes 04 HSDC-8919II-1 60 Hz, 90 V, Synchro-to-digital converter 4.0 arc minutes 05 HSD1024-C672H/2 400 Hz, 11.8 V, Syn

12、chro-to-digital converter 2.6 arc minutes 06 HSD1024-C673S/2 400 Hz, 11.8 V, Synchro-to-digital converter 4.0 arc minutes 07 HSD1024-C674H/2 60 Hz, 90 V, Synchro-to-digital converter 2.6 arc minutes 08 HSD1024-C675S/2 60 Hz, 90 V, Synchro-to-digital converter 4.0 arc minutes 1.2.3 Device class desig

13、nator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels ar

14、e as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Re

15、duced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Gro

16、up A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that

17、 the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking perm

18、itted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90707 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter

19、Descriptive designator Terminals Package style X See figure 1 36 Dual-in-line Y See figure 1 36 Dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) +18 V dc Logic input voltage (VL) +15 V dc Reference input 130

20、V rms Digital inputs range -0.3 V dc to VL Power dissipation (PD): Device types 01-04. 270 mW 2/ Device types 05-08. 380 mW 2/ Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . 8.0C/W Thermal resistance, junction-to-am

21、bient (JA) 28C/W Junction temperature (TJ) 150C 1.4 Recommended operating conditions. Supply voltage range (VS) +11 V dc to +16.5 V dc Logic input voltage range (VL) +4.5 V dc to +15 V supply Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification,

22、 standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 -

23、Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK

24、-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In th

25、e event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratin

26、gs may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Power dissipation applies up to TA= +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

27、DRAWING SIZE A 5962-90707 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compli

28、ance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the perform

29、ance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construct

30、ion, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram(s). The blo

31、ck diagram(s) shall be as specified on figure 3. 3.2.4 Digital angle output(s). The digital angle output(s) shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and sha

32、ll apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in acc

33、ordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall mainta

34、in the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained

35、 under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (origi

36、nal copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this draw

37、ing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2

38、 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be m

39、ade available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of meth

40、od 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

41、t license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90707 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Gr

42、oup A subgroups Device types Min Max Unit Resolution control 14 bits fail/pass 7,8 All Output accuracy Measured at angles of 0, 15, 30, 45, 60, 75, 90, 105, 120, 135, 150, 165, 180, 225, 270, and 315 degrees 7,8 All 2/ Reference input Input voltage range 3/ VIN 4,5,6 All 4.0 130 V rms 01,02 360 1000

43、 05,06 360 800 03,04 47 1000 Carrier frequency 3/ 4,5,6 07,08 47 800 Hz Single ended 250 Input impedance 3/ ZINREFDifferential 4,5,6 All 500 k Common mode voltage range 3/ VCMREF4,5,6 All -210 +210 V (pk) Signal input 01,02,05,06 -60 +60 Common mode range 3/ VCMSIG4,5,6 03,04,07,08 -182 +182 V(pk) 0

44、1,02,05,06 17.5 Line to line 4,5,6 03,04,07,08 130 k 01,02,05,06 11.5 Input impedance 3/ ZINSIGEach line to ground 4,5,6 03,04,07,08 8.5 k See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SI

45、ZE A 5962-90707 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device types Min Max Unit S

46、ignal input - Continued. 01,02,05,06 10.62 12.98 Line to line input voltage 3/ VINL-L Line-to-line 4,5,6 03,04,07,08 81 99 V rms Digital outputs (bits 1 through 14 and converter busy) VOLLogic 0, 1 TTL load at -1.6 mA 1,2,3 All 0.4 V dc VOHLogic 1, 10 TTL loads at 0.4 mA 1,2,3 All 2.8 V dc Drive cap

47、ability IXHigh impedance load, bits 1 through 14 only 1,2,3 All -10 +10 A Converter busy CB Positive pulse 9,10,11 All 0.5 2.5 s Analog output 01,02,03,04 12.8 19.2 Ac error 3/ e For 1.0 LSB change, near null to ground 4,5,6 05,06,07,08 11.0 21.0 mV rms/ LSB At 2.1 rps 4,5,6 01,02,05,06 0.8 1.2 DC v

48、elocity voltage 3/ At 0.54 rps 4,5,6 03,04,07,08 0.8 1.2 V dc 01,02,03,04 -1.2 -0.8 Filtered dc error 3/ E Per + LSB of error 4,5,6 05,06,07,08 -1.3 -0.7 V dc Full scale max., positive direction 4,5,6 All 3.72 5.70 V dc Velocity 4/ v Full scale max., negative direction 4,5,6 All -3.73 -5.70 V dc See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5