DLA SMD-5962-90665 REV B-2012 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED LOW POWER SCHOTTKY TTL 3 LINE TO 8 LINE DECODER MULTIPLEXERS WITH ADDRESS LATCHES MONOLITHIC SILICON.pdf

《DLA SMD-5962-90665 REV B-2012 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED LOW POWER SCHOTTKY TTL 3 LINE TO 8 LINE DECODER MULTIPLEXERS WITH ADDRESS LATCHES MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90665 REV B-2012 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED LOW POWER SCHOTTKY TTL 3 LINE TO 8 LINE DECODER MULTIPLEXERS WITH ADDRESS LATCHES MONOLITHIC SILICON.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 05-05-26 Raymond Monnin B Update drawing as part of 5 year review. - -jt 12-08-01 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.

2、 REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Larry T. Gauder DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS

3、AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Tim H. Noh APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, 3 LINE TO 8 LINE DECODER/MULTIPLEXERS WITH ADDRESS LATCHES, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-03-06 AMSC N/A REVISION LEVEL B SIZE

4、 A CAGE CODE 67268 5962-90665 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E341-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DS

5、CC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Numbe

6、r (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90665 01 M E X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline

7、(see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A spec

8、ified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function 01 54ALS137 3-line to 8-line decoders/multiplexers with address latch

9、es 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accord

10、ance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 dual-in-line F GDFP2-F16 or C

11、DFP3-F16 16 flat 2 CQCC1-N20 20 square chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDA

12、RD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range VCC-0.5 V dc to +7.0 V dc DC input voltage -1.52 V dc at -18 mA to +7.0 V dc Storage temperature range -65C t

13、o +150C Maximum power dissipation (PD) 2/ . 60.5 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Minimum high level

14、 input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL): TC= +125C . 0.7 V dc TC= -55C 0.8 V dc TC= +25C . 0.8 V dc Maximum high level output current (IOH) -0.4 mA Maximum low level output current (IOL) +4 mA Case operating temperature range (TC) -55C to +125C Minimum setup time at A,

15、B, and C before GL rising (ts) . 15 ns Maximum hold time at A, B, and C after GL rising (th) . 5 ns Minimum pulse duration, GL low (tw) . 15 ns 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this dr

16、awing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-

17、883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at htt

18、ps:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precede

19、nce. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reli

20、ability. 2/ Maximum power dissipation is defined as VCCX ICC, and must withstand the added PDdue to short circuit test e.g., IO. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COL

21、UMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) p

22、lan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and phy

23、sical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal

24、 connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 3. 3.3 Electrical performance character

25、istics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical

26、 test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD

27、 PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for devic

28、e class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A

29、. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufact

30、urer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q

31、 and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix

32、A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that a

33、ffects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made

34、available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 10 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted withou

35、t license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups

36、Device type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, 2/ VIH= 2.0 V, VILat: +125C = 0.7 V -55C = 0.8 V +25C = 0.8 V IOH= -0.4 mA 1, 2, 3 All 2.5 V Low level output voltage VOL VCC= 4.5 V, VIH= 2.0 V, IOL= 4 mA 2/ VILat: +125C = 0.7 V -55C = 0.8 V +25C = 0.8 V 1, 2, 3 All 0.4 V Inp

37、ut clamp voltage VI C VCC= 4.5 V IIN= -18 mA 1, 2, 3 All -1.5 V High level input current, IIH1 VCC= 5.5 V, VIN= 7.0 V 1, 2, 3 All 100 A IIH2 VIN= 2.7 V 1, 2, 3 All 20 Low level input current IIL VCC= 5.5 V VIN= 0.4 V 1, 2, 3 All -0.1 mA Output current IOVCC= 5.5 V VOUT= 2.25 V 3/ 1, 2, 3 All -20 -11

38、2 mA Supply current ICC VCC= 5.5 V 1, 2, 3 All 11 mA Functional tests See 4.4.1b, VCC= 4.5 V and 5.5 V 7, 8 All Propagation delay time, from A, B, C to Y tPLH1VCC= 4.5 V and 5.5 V, CL= 50 pF RL= 500 2/ 9, 10, 11 All 5 25 ns tPHL1 9, 10, 11 All 6 25 ns Propagation delay time, G 2 to Y tPLH29, 10, 11

39、All 4 15 ns tPHL2 9, 10, 11 All 5 18 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM

40、2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TC +125C 1/ unless otherwise specified Group A subgroups Device type Limits Unit Min Max Propagation delay time, G1 to Y tPLH3 VCC= 4.5 V and 5.5 V, CL= 50 pF, RL= 500, see figure 3 4/ 9, 10, 11 All 5

41、21 ns tPHL3 9, 10, 11 All 5 19 ns Propagation delay time, GL to Y tPLH4 9, 10, 11 All 7 27 ns tPHL4 9, 10, 11 All 7 25 ns 1/ Unused inputs that do not directly control the pin under test must be put at 2.5 V or 0.4 V. No unused inputs shall exceed 5.5 V or go less than 0.0 V. No inputs shall be floa

42、ted. 2/ All outputs must be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper state, the test must be performed with each input being selected as the VILmaximum or VIHminimum input. 3/ The output conditions have been chosen to produce a current that closely app

43、roximates one half of the true short circuit output current, IOS. Not more than one output will be tested at one time and duration of the test condition shall not exceed 1 second. 4/ Propagation delay limits are based on single output switching. Unused inputs = 3.5 V or 0.3 V. Provided by IHSNot for

44、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines E, F 2 Terminal number Terminal symbol 1 A NC 2 B A

45、3 C B 4 GL C 5 G 2 GL 6 G1 NC 7 Y7 G 2 8 GND G1 9 Y6 Y7 10 Y5 GND 11 Y4 NC 12 Y3 Y6 13 Y2 Y5 14 Y1 Y4 15 Y0 Y3 16 VCCNC 17 - - - Y2 18 - - - Y1 19 - - - Y0 20 - - - VCCFIGURE 1. Terminal connections. Inputs Outputs Enable Select GL G1 G 2 C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 X X H X X X H H H H H H H H X L

46、 X X X X H H H H H H H H L H L L L L L H H H H H H H L H L L L H H L H H H H H H L H L L H L H H L H H H H H L H L L H H H H H L H H H H L H L H L L H H H H L H H H L H L H L H H H H H H L H H L H L H H L H H H H H H L H L H L H H H H H H H H H H L H H L X X X Output corresponding to stored address,

47、 L; all others, H H = High voltage level L = Low voltage level x = Irrelevant FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVIS

48、ION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 NOTES: 1. CL includes probe and jig capacitance. 2. All inputs have the following characteristics: PRR = 10 MHz, tr= tf= 3 ns, duty cycle = 50 percent. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 3. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90665 DLA LAND AND