DLA SMD-5962-90640 REV D-2010 MICROCIRCUIT DIGITAL CMOS QUAD BILATERAL SWITCH MONOLITHIC SILICON.pdf

《DLA SMD-5962-90640 REV D-2010 MICROCIRCUIT DIGITAL CMOS QUAD BILATERAL SWITCH MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90640 REV D-2010 MICROCIRCUIT DIGITAL CMOS QUAD BILATERAL SWITCH MONOLITHIC SILICON.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 + REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R270-92 92-08-07 Monica L. Poelking B Redrawn with changes. Add device type 02. Editorial changes throughout. 94-02-22 Monica L. Poelking C Update boilerplate to MIL-PRF-38535 requirements. Editorial changes

2、throughout. LTG 03-08-22 Thomas M. Hess D Correct the condition IOfor VOHand VOLtest in table I. Update boilerplate paragraphs to the latest MIL-PRF-38535 requirements. jak 10-04-26 Thomas M. Hess CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1

3、2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Marcia B. Kelleher DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIR

4、CUIT, DIGITAL, CMOS, QUAD BILATERAL SWITCH, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-10-15 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 14933 5962-90640 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E228-10 Provided by IHSNot for ResaleNo reproduction or network

5、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class l

6、evel B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-90640 01 C A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type

7、(s) identify the circuit function as follows: Device type Generic number Circuit function 01 4016B Quad bilateral switch 02 14016B Quad bilateral switch 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Packag

8、e style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line package 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range, device type 01 -0.5 V dc to +20 V dc Supply voltage range, device type 02 -0.5 V dc to +18 V dc Input voltage

9、range (VIN) -0.5 V dc to VDD+ 0.5 V dc DC input current . 10 mA Storage temperature range -65C to +150C Maximum power dissipation (PD) . 500 mW 1/ Lead temperature (soldering, 10 seconds) . +300C- Thermal resistance, junction-to-case (JC): See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recom

10、mended operating conditions. Supply voltage range (VDD), device type 01 . +3.0 V dc to +18 V dc Supply voltage range (VDD), device type 02 . +3.0 V dc to +15 V dc Case operating temperature range (TC) . -55C to +125C 1/ For TC= +100C to +125C, derate linearly at 12 mW/C to 200 mW. Provided by IHSNot

11、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and

12、 handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circ

13、uits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780

14、- Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the

15、 text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall

16、 be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification

17、to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modi

18、fications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimen

19、sions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 T

20、ruth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figures 4 and 5. 3.3 Electrical performance character

21、istics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DR

22、AWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in tab

23、le I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For packages where marking of the entire SMD PIN number is n

24、ot feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall

25、be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (se

26、e 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance

27、 as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535, appendix A. 3.9 Verification and review. DSCC, DSCCs agent, and the

28、acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STA

29、NDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C unless otherwise specified Device type Group A subgroups Limits Un

30、it Min Max Quiescent supply current IDDVDD= 5.0 V VIN= 0.0 V or VDD1/ All 1, 3 0.25 A 2 7.5VDD= 10 V VIN= 0.0 V or VDD1/ All 1, 3 0.5 2 15VDD= 15 V VIN= 0.0 V or VDD1/ All 1, 3 1 2 30 VDD= 20 V VIN= 0.0 V or VDD2/ 01 1, 3 5 2 150 Low level output voltage VOLVIN= 0.0 V or VDDIOL 1 A VDD= 5 V 1/ 02 1,

31、 2, 3 0.05 V VDD= 10 V 1/ 02 1, 2, 3 0.05 VDD= 15 V 02 1, 2, 3 0.05 High level output voltage VOHVIN= 0.0 V or VDDIOH 1 A VDD= 5 V 1/ 02 1, 2, 3 4.95 VDD= 10 V 1/ 02 1, 2, 3 9.95 VDD= 15 V 02 1, 2, 3 14.95 Low level input voltage, control inputs VILVDD= 5.0 V IIL 10 A VIN= GND VOUT= VDDand VIN= VDDV

32、OUT= GND 01 1 0.7 V 2 0.4 3 0.902 1, 2, 3 0.9 VDD= 10 V IIL 10 A 1/ VIN= GND VOUT= VDDand VIN= VDDVOUT= GND 01 1 0.7 2 0.4 3 0.902 1, 2, 3 0.9 VDD= 15 V IIL 10 A VIN= GND VOUT= VDDand VIN= VDDVOUT= GND 01 1 0.72 0.4 3 0.902 1, 2, 3 0.9 High level input voltage, control VIHVDD= 5.0 V 01 1, 2, 3 3.5 V

33、 02 3.0VDD= 10 V 1/ 01 1, 2, 3 7.0 02 8.0VDD= 15 V 01 1, 2, 3 11.0 02 13.0See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 432

34、18-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C unless otherwise specified Device type Group A subgroups Limits Unit Min Max Low level output current IOLVDD= 5.0 V 3/ VOUT= 0.4 V VIN= 0.0 V or VDD

35、 02 1 0.51 mA 2 0.36 3 0.64 VDD= 10 V 1/ VOUT= 0.5 V VIN= 0.0 V or VDD 02 1 1.3 2 0.9 3 1.6 VDD= 15 V 1/ VOUT= 1.5 V VIN= 0.0 V or VDD 02 1 3.4 2 2.4 3 4.2 High level output current IOHVDD= 5.0 V 3/ VOUT= 4.6 V VIN= 0.0 V or VDD02 1 -0.51 mA 2 -0.36 3 -0.64 VDD= 5.0 V 3/ VOUT= 2.5 V VIN= 0.0 V or VD

36、D02 1 -1.6 mA 2 -1.15 3 -2.0 VDD= 10 V 1/ VOUT= 9.5 V VIN= 0.0 V or VDD 02 1 -1.3 mA 2 -0.9 3 -1.60 VDD= 15 V 1/ VOUT= 13.5 V VIN= 0.0 V or VDD02 1 -3.4 mA 2 -2.4 3 -4.2 Input current IINVDD= 20 V 2/ VIN= 0.0 V or VDD01 1, 3 0.1 A 2 1.0 VDD= 15 V VIN= 0.0 V or VDD02 1, 3 0.1 2 1.0 See footnotes at e

37、nd of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance chara

38、cteristics - Continued. Test Symbol Conditions -55C TC+125C unless otherwise specified Device type Group A subgroups Limits Unit Min Max Input/output leakage current (Switch off) IISVCONTROL= 0 V VIN= 18 V VOUT= 0.0 V All 1, 3 0.1 A 2 1.0 VCONTROL= 0 V VIN= 0.0 V VOUT= 18 V All 1, 3 0.1 A 2 1.0 On-s

39、tate resistance RONVCONTROL= VDDRL= 10 k returned to VDD GND/2 VDD= 10 V VIN= VDDor GND All 1 660 2 960 3 600 VDD= 10 V VIN= 4.75 V to 5.75 V 1 2000 2 2600 3 1870 VDD= 15 V VIN= VDDor GND 1 400 2 600 3 360 VDD= 15 V VIN= 7.25 V to 7.75 V 1 850 2 1230 3 775 Delta on-state resistance between any two s

40、witches RONVCONTROL = VDD RL= 10 k 1/ VSS= 0.0 V VDD= 5 V 01 1 15 VDD= 10 V 01 1 15 02 1 15 VDD= 15 V 01 1 10 02 1 10 Input capacitance CINVDD= GND See 4.3.1c All 4 7.5 pF Functional test See 4.3.1d All 7, 8 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking pe

41、rmitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C unless otherwi

42、se specified Device type Group A subgroups Limits Unit Min Max Propagation delay time, input to output tPHL, tPLHRL= 200 k device 01 RL= 10 k device 02 CL= 50 pF tr, tf= 20 ns VCONTROL= VDDVIN= VDD(square wave centered on VDD/2) See figure 4 VDD= 5 V All 9 1.5 4/ 100 ns 10, 11 1.5 4/ 160 VDD= 10 V 1

43、/ 9 1.5 4/ 40 10, 11 1.5 4/ 64 VDD= 15 V 1/ 9 1.5 4/ 30 10, 11 1.5 4/ 48 Propagation delay time, control input to switch output (turn on) tPHZ, tPLZ, tPZH, tPZLRL= 1 k CL= 50 pF tr, tf= 20 ns See figure 5 VDD= 5 V All 9 1.5 4/ 70 ns 10, 11 1.5 4/ 112 VDD= 10 V 1/ 9 1.5 4/ 40 10, 11 1.5 4/ 64 VDD= 15

44、 V 1/ 9 1.5 4/ 30 10, 11 1.5 4/ 48 1/ For device type 01, this parameter is guaranteed, if not tested, to the limits specified in table I. 2/ At -55C, this test is performed with VDD= 18 V dc. 3/ The IOLand IOHtests are tested 100 percent at TC= +25C, and are guaranteed, if not tested, for TC= -55C

45、and TC= +125C. 4/ The minimum limit for device type 01 only = 1.5 ns. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DS

46、CC FORM 2234 APR 97 Device types 01 and 02 Case outline C Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 INPUT/OUPUT SIG A OUTPUT/INPUT SIG A OUTPUT/INPUT SIG B INPUT/OUTPUT SIG B CONTROL B CONTROL C GND INPUT/OUTPUT SIG C OUTPUT/INPUT SIG C OUTPUT/INPUT SIG D INPUT/OUTPUT SIG D CO

47、NTROL D CONTROL A VDDFIGURE 1. Terminal connections. Each switch Inputs Output VCONTROL VINVOUTH H L L L H L H L H OPEN OPEN H = High voltage level (steady-state) L = Low voltage level (steady-state) Positive logic: Switch on VCONTROL= High Switch off VCONTROL= Low FIGURE 2. Truth table. Provided by

48、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90640 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT