DLA SMD-5962-89490 REV D-2012 MICROCIRCUIT HYBRID LINEAR DUAL POSITIVE AND NEGATIVE 15-VOLT 12-VOLT AND 5-VOLT REGULATOR.pdf

《DLA SMD-5962-89490 REV D-2012 MICROCIRCUIT HYBRID LINEAR DUAL POSITIVE AND NEGATIVE 15-VOLT 12-VOLT AND 5-VOLT REGULATOR.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89490 REV D-2012 MICROCIRCUIT HYBRID LINEAR DUAL POSITIVE AND NEGATIVE 15-VOLT 12-VOLT AND 5-VOLT REGULATOR.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device type 02 through 09. Editorial changes throughout. 92-06-02 G. A. Lude B Updated drawing to the latest MIL-PRF-38534 requirements. 05-01-21 Raymond Monnin C Table I, Standby current drain change with line, add note 3 to the test descr

2、iption block, for all device types (6 places). Table I, Ripple rejection, conditions column, add VINcondition for all device types. Table I, note 1, correct VINfor -12 V output to VIN= -19 V. 06-04-19 Raymond Monnin D Updated drawing paragraphs. -sld 12-02-02 Charles F. Saffle THE ORIGINAL FIRST PAG

3、E OF THIS DRAWING HAS BEEN REPLACED REV SHEET REV D D SHEET 15 16 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Donald R. Osborne DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUI

4、T DRAWING CHECKED BY Robert M. Heber THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY D. M. Cool MICROCIRCUIT, HYBRID, LINEAR, DUAL POSITIVE AND NEGATIVE 15-VOLT, 12-VOLT, AND 5-VOLT REGULATOR DRAWING APPROVAL DATE 90-07-19 AMSC N/A REVISION

5、LEVEL D SIZE A CAGE CODE 67268 5962-89490 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E155-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D

6、 SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2

7、 PIN. The PIN shall be as shown in the following example: 5962- 89490 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 OM390

8、9, SD11089 Dual, fixed, voltage regulator, +15 V output and -15 V output 02 OM3901, SD11081 Dual, fixed, voltage regulator, +5 V output and -5 V output 03 OM3902, SD11082 Dual, fixed, voltage regulator, +5 V output and -12 V output 04 OM3903, SD11083 Dual, fixed, voltage regulator, +5 V output and -

9、15 V output 05 OM3904, SD11084 Dual, fixed, voltage regulator, +12 V output and -5 V output 06 OM3905, SD11085 Dual, fixed, voltage regulator, +12 V output and -12 V output 07 OM3906, SD11086 Dual, fixed, voltage regulator, +12 V output and -15 V output 08 OM3907, SD11087 Dual, fixed, voltage regula

10、tor, +15 V output and -5 V output 09 OM3908, SD11088 Dual, fixed, voltage regulator, +15 V output and -12 V output 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 5 Flange mount

11、1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ 2/ Input voltage (positive output) . +35 V dc Input voltage (negative output) . -35 V dc Thermal shutdown (IO= 5.0 mA at rated VOUT) . +175 C Power dissipation (PD): TA= +25 C 3.0 W TC= +25 C

12、17.5 W Storage temperature range . -65 C to +150 C Lead temperature (soldering, 10 seconds) . +300 C Thermal resistance, junction-to-case (qJC) 3.0 C/W Thermal resistance, junction-to-ambient (qJA) . 42 C/W Junction temperature (TJ) . +150 C 1.4 Recommended operating conditions. Ambient operating te

13、mperature range (TA) -55 C to +125 C _ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Absolute maximum ratings apply to each regulator.Provided by IHSNot for ResaleNo

14、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow

15、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specif

16、ication for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawing

17、s. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the r

18、eferences cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements shall be in accordance w

19、ith MIL-PRF-38534. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The

20、 terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requ

21、irements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 here

22、in. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance in

23、spection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to th

24、e preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that t

25、he manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D

26、SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max +15 V output Output voltage VOUTVIN= 18.5 V to 30 V, IO= 5.0 mA to 1.0 A, P 15 W 1 1,8,9 14.8 15.2

27、 V 2,3 14.6 15.4 Line regulation 3/ VRLINEVIN= 17.5 V to 30 V 1 75 mV 2,3 150 VIN= 20 V to 25 V 1 40 2,3 80 Load regulation VRLOADIO= 5.0 mA to 1.5 A 1 100 2,3 200 IO= 250 mA to 750 mA 1 50 2,3 100 Standby current drain ISCD1 6.0 mA 2,3 7.0 Standby current drain 3/ change with line ISCD (line) VIN=

28、18.5 V to 30 V 1,2,3 0.8 Standby current drain change with load ISCD (load) IO= 5.0 mA to 1000 mA 1,2,3 0.5 Dropout voltage VDOIO= 1.0 A, VOUT= 100 mV 1,2,3 2.5 V Peak output current IO(pk)TC= +25 C 1 1.5 3.3 A Short circuit current 4/ IOSVIN= 35 V 1 1.2 2,3 2.8 See footnotes at end of table. Provid

29、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test

30、 Symbol Conditions 1/ 2/ -55 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max +15 V output - Continued. Ripple rejection VIN/VOUTTC= +25 C, f = 120 Hz, VIN= 10 V, VIN= 23 V 4 1,8,9 54 dB 5,6 5/ 51 Output noise voltage 5/ NOTC= +25 C 7 40 mA/V rms Long term st

31、ability 5/ VOUT/t TC= +25 C, t = 1000 hours 7 150 mV -15 V output Output voltage VOUTVIN= -17.5 V to -30 V, IO= 5.0 mA to 1.0 A, P 15 W 1 1,4,7 -14.85 -15.45 V 2,3 -14.55 -15.45 Line regulation 3/ VRLINEVIN= -17.5 V to -30 V 1 20 mV 2,3 50 VIN= -20 V to -26 V 1 15 2,3 25 Load regulation VRLOADIO= 5.

32、0 mA to 1.5 A 1 35 2,3 75 IO= 250 mA to 750 mA 1 21 2,3 45 Standby current drain ISCD1 6.0 mA 2,3 6.5 Standby current drain change with line 3/ ISCD (line) VIN= -17.5 V to -30 V 1,2,3 0.8 Standby current drain change with load ISCD (load) IO= 5.0 mA to 1000 mA 1,2,3 0.5 See footnotes at end of table

33、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continu

34、ed. Test Symbol Conditions 1/ 2/ -55 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max -15 V output - Continued. Dropout voltage VDOIO= 1.0 A, VOUT= 100 mV 1,2,3 1,4,7 2.5 V Peak output current IO(pk)TC= +25 C 1 1.5 3.3 A Short circuit current 4/ IOSVIN= -35 V

35、 1 1.2 2,3 2.8 Ripple rejection VIN/VOUTTC= +25 C, f = 120 Hz, VIN= -10 V, VIN= -23 V 4 53 dB 5,6 5/ 50 Output noise voltage 5/ NOTC= +25 C, f = 10 Hz to 100 kHz 7 40 mA/V rms Long term stability 5/ VOUT/t TC= +25 C, t = 1000 hours 7 150 mV +12 V output Output voltage VOUTVIN= 14.5 V to 27 V, IO= 5.

36、0 mA to 1.0 A, P 15 W 1 5,6,7 11.88 12.12 V 2,3 11.64 12.36 Line regulation 3/ VRLINEVIN=14.5 V to 27 V 1 18 mV 2,3 50 VIN= 16 V to 22 V 1 9 2,3 30 Load regulation VRLOADIO= 5.0 mA to 1.5 A 1 32 2,3 60 IO= 250 mA to 750 mA 1 20 2,3 40 See footnotes at end of table. Provided by IHSNot for ResaleNo re

37、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55

38、 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max +12 V output - Continued. Standby current drain ISCD1 5,6,7 6.0 mA 2,3 6.5 Standby current drain 3/ change with line ISCD (line) VIN= 14.5 V to 27 V 1,2,3 0.8 Standby current drain change with load ISCD (load)

39、 IO= 5.0 mA to 1000 mA 1,2,3 0.5 Dropout voltage VDOIO= 1.0 A, VOUT= 100 mV 1,2,3 2.5 V Peak output current IO(pk)TC= +25 C 1 1.5 3.3 A Short circuit current 4/ IOSVIN= 35 V 1 1.2 2,3 2.8 Ripple rejection VIN/VOUTTC= +25 C, f = 120 Hz, VIN= 10 V, VIN= 20 V 4 59 dB 5,6 5/ 54 Output noise voltage 5/ N

40、OTC= +25 C 7 40 mA/V rms Long term stability 5/ VOUT/t TC= +25 C, t = 1000 hours 7 120 mV -12 V output Output voltage VOUTVIN= -14.5 V to -27 V, IO= 5.0 mA to 1.0 A, P 15 W 1 3,6,9 -11.8 -12.2 V 2,3 -11.6 -12.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking

41、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55 C TC +125 C unless othe

42、rwise specified Group A subgroups Device types Limits Unit Min Max -12 V output - Continued. Line regulation 3/ VRLINEVIN= -14.5 V to -27 V 1 3,6,9 20 mV 2,3 50 VIN= -16 V to -22 V 1 10 2,3 30 Load regulation VRLOADIO= 5.0 mA to 1.5 A 1 32 2,3 60 IO= 250 mA to 750 mA 1 16 2,3 30 Standby current drai

43、n ISCD1 3.5 mA 2,3 4.0 Standby current drain 3/ change with line ISCD (line) VIN= -14.5 V to -27 V 1,2,3 0.8 Standby current drain change with load ISCD (load) IO= 5.0 mA to 1000 mA 1,2,3 0.5 Dropout voltage VDOIO= 1.0 A, VOUT= 100 mV 1,2,3 2.5 V Peak output current IO(pk)TC= +25 C 1 1.5 3.3 A See f

44、ootnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance c

45、haracteristics - Continued. Test Symbol Conditions 1/ 2/ -55 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max -12 V output - Continued. Short circuit current 4/ IOSVIN= -35 V 1 3,6,9 1.2 A 2,3 2.8 Ripple rejection VIN/VOUTTC= +25 C, f = 120 Hz, VIN= -10 V, VI

46、N= -20 V 4 56 dB 5,6 5/ 53 Output noise voltage 5/ NOTC= +25 C 7 40 mA/V rms Long term stability 5/ VOUT/t TC= +25 C, t = 1000 hours 7 120 mV +5 V output Output voltage VOUTVIN= 7.5 V to 20 V, IO= 5.0 mA to 1.0 A, P 15 W 1 2,3,4 4.92 5.08 V 2,3 4.85 5.15 Line regulation 3/ VRLINEVIN= 7.5 V to 20 V 1

47、 5 mV 2,3 12 VIN= 8 V to 12 V 1 4 2,3 10 Load regulation VRLOADIO= 5.0 mA to 1.5 A 1 12 2,3 25 IO= 250 mA to 750 mA 1 15 2,3 30 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-8

48、9490 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55 C TC +125 C unless otherwise specified Group A subgroups Device types Limits Unit Min Max +5 V output - Continued. Standby current drain ISCD1 2,3,4 6.0 mA 2,3 6.5 Standby current drain 3/ change with line ISCD (line) VIN= 7.5 V to 20 V 1,2,3 0.8 Standby current drain chang