DLA SMD-5962-88564 REV C-2011 MICROCIRCUIT LINEAR QUAD 2-INPUT OR DRIVER HIGH-OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON.pdf

《DLA SMD-5962-88564 REV C-2011 MICROCIRCUIT LINEAR QUAD 2-INPUT OR DRIVER HIGH-OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-88564 REV C-2011 MICROCIRCUIT LINEAR QUAD 2-INPUT OR DRIVER HIGH-OUTPUT VOLTAGE AND CURRENT MONOLITHIC SILICON.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change conditions for VIN(1)and VIN(0). Change pinout for case D. Add input pulse characteristics to waveforms and switching circuit. Add description of Icc(1)and ICC(0). 89-02-22 M. A. Frye B Drawing updated to reflect current requirements. Edit

2、orial changes throughout. drw 01-01-30 Raymond Monnin C Redraw. Update paragraphs to current boilerplate requirements. - drw 11-10-25 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/

3、A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Ray Monnin APPROVED BY Michael A. Frye MICROCIRCUIT,

4、 LINEAR, QUAD 2-INPUT OR DRIVER, HIGH-OUTPUT VOLTAGE AND CURRENT, MONOLITHIC SILICON DRAWING APPROVAL DATE 88-10-07 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-88564 SHEET 1 OF 8 DSCC FORM 2233 APR 97 5962-E474-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without

5、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88564 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accord

6、ance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88564 01 C A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identifies the circuit function

7、as follows: Device type Generic number Circuit function 01 UH502 Quad 2-input OR driver, high-output voltage and current 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14

8、Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat package 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) 7.0 V dc Input voltage 5.5 V dc Output off-state voltage . 100 V dc Output on-state sink current 500 mA Storage te

9、mperature range -65C to +150C Lead temperature (soldering 10 seconds) . +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC): Case C and D. See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case outline C 90C/W Case outline D 140C/W 1.4 Recommended operating c

10、onditions. Positive supply voltage range (VCC) . 4.5 V to 5.5 V Current into any output (on-state) 250 mA maximum Ambient operating temperature range (TA) -55C to +125C Minimum high level input voltage (VIH) . 2.0 V Maximum low level input voltage (VIL) . 0.8 V Provided by IHSNot for ResaleNo reprod

11、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88564 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following spe

12、cification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General

13、Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawi

14、ngs. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the

15、 references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PR

16、F-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be proce

17、ssed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect fo

18、rm, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, constructi

19、on, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Waveforms, switching circuit and i

20、nput pulse characteristics. The waveforms, switching circuit and input pulse characteristics shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over t

21、he full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without

22、license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88564 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C Group A subgroups Device type Limits Unit unless o

23、therwise specified Min Max Input current, high IIN(1) VCC= 5.5 V, driven input = 2.4 V, other input = 0 V 1, 2, 3 01 40 A VCC= 5.5 V, driven input = 5.5 V, other input = 0 V 1000 Input current, low IIN(0) VCC= 5.5 V, driven input = 0.4 V, other input = 4.5 V 1, 2, 3 01 -800 A Output reverse current

24、IOFFOther input = 0 V, driven input = 2.0 V, VCC= 4.5 V, VO= 100 V 1, 2, 3 01 100 A Output voltage, low VONVCC= 4.5 V, all inputs = 0.8 V 1, 3 01 0.5 V output = 150 mA 2 0.6 VCC= 4.5 V, all inputs = 0.8 V 1, 3 0.7 output = 250 mA 2 0.8 Supply current, high level (each gate) ICC(1) VCC= 5.5 V, all in

25、puts = 5.0 V TA= +25C 1 01 7.5 mA Supply current, low level (each gate) ICC(0) VCC= 5.5 V, all inputs = 0 V TA= +25C 1 01 26.5 mA Propagation delay, turn-on time tpdON VS= 100 V, CL= 15 pF 9, 10, 11 01 500 ns Propagation delay, turn-off time tpdOFF VCC= 5.0 V, RL= 670, See figure 2 750 Input voltage

26、, high VIN(1) VCC= 4.5 V 1, 2, 3 01 2.0 V Input voltage, low VIN(0) 0.8 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the ent

27、ire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The complian

28、ce indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of sup

29、ply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of

30、conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3

31、.9 Verification and review. DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by

32、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88564 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 Device type 01 Case outline C D Terminal number Terminal symbol 1 1Y 1A

33、 2 1A 1B 3 1B 1Y 4 2Y VCC5 2A 2Y 6 2B 2A 7 GND 2B 8 3A 3Y 9 3B 3A 10 3Y 3B 11 4A GND 12 4B 4A 13 4Y 4B 14 VCC4Y FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88564 DLA LAND A

34、ND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 FIGURE 2. Waveforms, switching circuit and input pulse characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-885

35、64 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of

36、 MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

37、level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim a

38、nd final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883

39、, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 9, (10, 11)* Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. * Subgr

40、oups 10 and 11, If not tested, shall be guaranteed to the specified limits in table I. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.

41、 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A

42、 5962-88564 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test conditi

43、on A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accor

44、dance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6.

45、NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by

46、a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of us

47、ers. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the d

48、rawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime -VA. Provided